Crystal structure of BaBi2Ta2O9

The crystal structure of the Aurivillius compound Bi2BaTa2O9 prepared via the chemical route was determined by direct methods using EXPO97, and refined using the Rietveld method with conventional X-ray diffraction data. The structure was found to be tetragonal (space group I4/mmm, number 139) and Z = 2, isomorphic of the Bi2BaNb2O9 reported by Blake and co-workers in the literature (1997). Two refinements were performed using the two asymmetry functions of DBWS-9807 (release 20/May/99). The unit cell for each case are: a = 3.932 22(6) Å, c = 25.5053(6) Å (RA) and a = 3.93250(7) Å, c = 25.5069(6) Å (RCF). The differences for atom positions, interatomic distances and angles are in the range of one standard deviation. Final agreements factors are: Rwp = 7.97%, S = 1.84, RBragg = 4.28%(RA), Rwp = 7.98%, S = 1.84, RBragg = 4.30% (RCF). The occupancies of Ba and Bi in site 2b were refined but constrained to have their summation equal to 1.00. The same constraints were applied to the Ba and Bi of the 4e site. The results show that on site 2b there are 70% of Ba and 30% of Bi and on the site 4e there are 82% of Bi and 18% of Ba. The charge equilibrium is maintained for one standard deviation of the site occupancies. © 2000 International Centre for Diffraction Data.

Influencia del tratamiento térmico en la cristalización y rugosidad de películas delgadas de LiNbO3 depositadas por el método Spin Coating

Lithium niobate (LiNbO3) thin films with 1/1 stoichiometry were prepared by a spin-coating from polymeric precursor method. The films deposited on silicon (100) substrates, were thermally treated from 400° to 600°C for 3 hours in order to study the influence of thermal treatment on the crystallinity, microstructure, grain size and roughness. X-ray diffraction (XRD) results showed that LiNbO3 phase crystallizes at low temperature (400°C). It was observed by scanning electron microscopy (SEM) that it is possible to obtain dense thin films at temperatures around 500°C. The atomic force microscopy (AFM) results showed that the grain size and roughness are strongly influenced by the annealing temperature.

Modal Analysis of a Beam with a Tip Rotor by Using a Fundamental Response

The shape modes of a damped-free beam model with a tip rotor are determined by using a dynamical basis that is generated by a fundamental spatial free response. This is a non-classical distributed model for the displacements in the transverse directions of the beam which turns out to be coupled through boundary conditions due to rotation. Numerical calculations are performed by using the Ritz-Rayleigh method with several approximating basis.

Variance heterogeneity for milk yield in Brazilian and Colombian Holstein herds

Heterogeneity of variances for milk yield (MY) was determined for Brazilian and Colombian herds. The herds were grouped as high or low variability within each country, using as criterion the phenotypic standard deviation (PSD) of MY in the contemporary groups of cows, from the first to the sixth calving. Brazilian and Colombian herds with PSD greater than 1,168 kg or 1,012 kg, respectively, were classified as high variability while the herd groups with values lower than those were classified as low variability. The genetic parameters for MY within each herd group were estimated using bivariate analysis in an animal model and the restricted maximum likelihood method with a derivative free algorithm, using 72,280 first lactations of cows, daughters of 1,880 sires. Heterogeneous variances were found, and Brazilian herds with high PSD had the greatest additive and residual genetic variances and heritability coefficients for MY. MY genetic correlation coefficients between herds of high and low variability within each country were 0.96 and 0.93 while between countries they varied from 0.72 to 0.81, suggesting that there was a reclassification of animals in the two countries and also heterogeneity of variances. This phenomenon leads to the questioning of the strategy of imported semen usage and the need to do genetic evaluations to identify sires with greater genetic potential for (sub) tropical environmental conditions.

Avaliação da eficiência dos métodos Direto, COPROTEST e Rugai no diagnóstico da estrongiloidíase

Strongyloidiasis, a relatively common parasitism in tropical and sub-tropical areas, is the result of the infection by the smaller nematode, the Strongyloides stercoralis. Humans can be infected by this parasite, which has in its vital cycle free-life forms of male and female individuals able to live in the ground, and with another step necessary parasitism in the intestinal wall. The diagnostic of the infection is routinely done by the microscopic observation of the larva in stool samples and the high sensibility of urn method over another one allows an trustable and efficient diagnostic. The efficiency of three methods (Direct, COPROTEST and Rugai) used in the Parasitology Sector of the NAC-LACAL in Araraquara (SP) to diagnosis the strongiloidiasis were evaluated. A number of 2346 samples of stool of patients from NAC-LACAL and Nestor Goulart Reis Hospital were analyzed in the period between August and December of 2002. The Rugai Method with an positivity index of 65 % was elected as the most efficient of thee ones.

Articaine and mepivacaine efficacy in postoperative analgesia for lower third molar removal: a double-blind, randomized, crossover study

Objective: Comparison of the clinical efficacy of 4% articaine in relation to 2% mepivacaine, both with 1:100,000 epinephrine, in the prevention of postoperative pain after lower third molar removal. Study design: Twenty patients underwent removal of bilateral lower third molars under local anesthesia (articaine or mepivacaine) in 2 separate appointments, in a double-blind, randomized, and crossed manner. Objective and subjective parameters were recorded for paired comparison of postoperative courses. Results: Duration of analgesia provided by articaine and mepivacaine was 198.00 ± 25.86, and 125.40 ± 13.96 min, respectively (P = .02), whereas the duration of anesthesia was 273.80 ± 15.94 and 216.85 ± 20.15 min, respectively (P = .06). Both solutions exerted no important effects upon arterial pressure, heart rate, or oxygen saturation (P > .05). Conclusions: Articaine provides a longer period of analgesic effect and a tendency for a longer period of anesthesia as compared to mepivacaine. The presence of a vasoconstrictor agent in local anesthetic solutions does not seem to influence hemodynamic parameters during lower third molar removal in healthy subjects. © 2006 Mosby, Inc. All rights reserved.

The electronic detail of a digital pH-meter

This paperwork presents the complete circuitry used to build a microcontroller-based pH-meter. Key control software is also discussed. An industry-standard glass combination electrode has been employed for pH detection. Electrode parameter extraction procedure is presented. Good measurement results, with 1 % error, have been attained. Copyright© (2006) by the International Measurement Federation (IMEKO).

Production and heat treatment of cast graphitic steels with additions of niobium

The optimal combination of the mechanical characteristics of austempered spheroidal graphitic cast steel together with modern casting techniques yielded an economically promising product. The maximum potential of the usage of these steels is related to fabrication and characterization techniques, among which, one of the most important is the cooling diagram (TTT curve). In this work, 3 heats of graphitic steels with the following nominal compositions were cast: 1.0 % C, 2.3 % Si, 0.4 % Mn, and with niobium contents of. 0.0 %, 0.5 % and 1.0 %. TTT curves were determined by dilatometric testing and test specimens of these steels were austempered. The samples were then characterized by hardness testing and optical and SEM microscopy. Tensile, impact (no notch) and wear testing were also performed. The addition of niobium produced significant alterations in the TTT diagrams. Increasing niobium content moves the pearlite transformation nose to the right and the bainitic transformation nose to the left. Tensile strength of these alloys was high, in the range of 1700 MPa and impact values were around of 45 Joules for alloy with 1 % Nb, 49 Joules for alloy with 0.5 % Nb and fracture did not occur for the alloy without the addition of Nb.

Enraizamento in vitro e aclimatização de mudas micropropagadas de Aloe vera L.

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The surface geometry of exotic nuclei

We analyze the surface geometry of the spherical even-even Ca, Ni, Sn and Pb nuclei using two approaches: The relativistic Dirac-Hartree-Bogoliubov one with several parameter sets and the non-relativistic Hartree-Fock-Bogoliubov one with the Gogny force. The proton and neutron density distributions are fitted to two-parameter Fermi density distributions to obtain the half-density radii and diffuseness parameters. Those parameters allow us to determine the nature of the neutron skins predicted by the models. The calculations are compared with existing experimental data. © 2007 American Institute of Physics.

Effects of basic fibroblast growth factor on density and morphology of fibroblasts grown on root surfaces with or without conditioning with tetracycline or EDTA.

A study was conducted to evaluate in vitro the effect of root surface conditioning with basic fibroblast growth factor (b-FGF) on morphology and proliferation of fibroblasts. Three experimental groups were used: non-treated, and treated with 50 microg or 125 microg b-FGF/ml. The dentin samples in each group were divided into subgroups according to the chemical treatment received before application of b-FGF: none, or conditioned with tetracycline-HCl or EDTA. After contact with b-FGF for 5 min, the samples were incubated for 24 h with 1 ml of culture medium containing 1 x 10(5) cells/ml plus 1 ml of culture medium alone. The samples were then subjected to routine preparation for SEM, and random fields were photographed. Three calibrated and blind examiners performed the assessment of morphology and density according to two index systems. Classification and regression trees indicated that the root surfaces treated with 125 microg b-FGF and previously conditioned with tetracycline-HCl or EDTA presented a morphology more suggestive of cellular adhesion and viability (P = 0.004). The density of fibroblasts on samples previously conditioned with EDTA, regardless of treatment with b-FGF, was significantly higher than in the other groups (P < 0.001). The present findings suggest that topical application of b-FGF has a positive influence on both the density and morphology of fibroblasts.

The effect of endodontic materials on the optical density of dyes used in marginal leakage studies

The aim of this study was to determine the effect of the exposure of different endodontic materials to different dye solutions by evaluating the optical density of the dye solutions. Seventy-five plastic tubes were filled with one of the following materials: AH Plus, Sealapex, Portland cement, MTA (Angelus and Pro Root) and fifteen control plastic tubes were not. Each specimen of material and control was immersed in a container with 1 ml of each dye solution. A 0.1 ml-dye solution aliquote was removed before immersion and after 12, 24, 48 and 72 hours of each specimen immersion to record its optical density (OD) in a spectrophotometer. Statistical analysis was performed with ANOVA and Tukey tests (5%). No significant difference was found among any of the solution OD values for AH Plus cement. Portland cement promoted different OD values after 12 hours of immersion. MTA-Angelus cement presented different OD values only for 2% rhodamine B and the MTA-Pro Root cement presented different OD values in all 2% rhodamine B samples. Sealapex cement promoted a reduction in the India Ink OD values. Dye evaluation through OD seems to be an interesting method to select the best dye solution to use in a given marginal leakage study.

Production and heat treatment of cast graphitic steels with additions of niobium

The optimal combination of the mechanical characteristics of austempered spheroidal graphitic cast steel together with modern casting techniques yielded an economically promising product. The maximum potentiality of the usage of these steels is related to fabrication and characterization techniques, among which, one of the most important is the cooling diagram (TTT curve). In this work, 3 heats of graphitic steels with the following nominal compositions were cast: 1.0%C, 2.3%Si, 0.4% Mn, and with niobium contents of 0.0%, 0.5% and 1.0%. TTT curves were determined by dilatometric testing and test specimens of these steels were austempered. The samples were then characterized by hardness testing and optical and SEM microscopy. Tensile, impact (no notch) and wear testing were also performed. The addition of niobium produced significant alterations in the TTT diagrams. Increasing niobium content moves the pearlite transformation nose to the right and the bainitic transformation nose to the left. Tensile strength of these alloys was high, in the range of 1700 MPa and impact values were around of 45 Joules for alloy with 1% Nb, 49 Joules for alloy with 0.5% Nb and fracture did not occur for the alloy without the addition of Nb.

Search for scalar neutrino superpartners in e+mu final states in p(p)over-bar collisions at root s=1.96 TeV

We report a search for R-parity-violating production and decay of sneutrino particles in the eμ final state with 1.04±0.06fb-1 of data collected with the D0 detector at the Fermilab Tevatron Collider in 2002-2006. Good agreement between the data and the standard model prediction is observed. With no evidence for new physics, we set limits on the R-parity-violating couplings λ311′ and λ312 as a function of the sneutrino mass. © 2008 The American Physical Society.

Effects of heat treatments on the electrocatalytic activity of Pt-Ru/C for methanol oxidation

The Pt-Ru/C materials of this study were prepared by a microemulsion method with fixed water to surfactant molar ratio and heat treated at low temperatures, to avoid changes in the average particle size, in different atmospheres. All samples were characterized by X-ray diffraction (XRD) and the mean crystallite size was estimated by using Scherrer's equation. Catalysts morphology was characterized by transmission electron microscopy (TEM). Average composition was obtained by energydispersive X-ray analysis (EDX). The general electrochemical behavior was evaluated by cyclic voltammetry in 0.5 M sulfuric acid and the electrocatalytic activity towards the oxidation of methanol was studied in 0.5 M methanol acid solutions by potential sweeps and chronoamperometry. Oxidation of adsorbed CO was used to estimate the electrochemical active area and to infer the surface properties. ©The Electrochemical Society.