EVALUATION OF EUCALYPTUS KRAFT PULP LIGNIN THROUGH THE NITROBENZENE OXIDATION, COPPER OXIDE REDUCTION AND ACIDOLYSIS TECHNIQUES

This study aimed to evaluate the sensitiveness of the information obtained for the residual lignin from Eucalyptus grandis kraft pulps analyzed through the nitrobenzene oxidation, copper oxide (CuO) reduction and acidolysis techniques. The chips were cooked, resulting pulps of kappa number 14,5 and 16,9, respectively. Both lignins' pulps were evaluated through three methods (nitrobenzene oxidation, copper oxide oxidation and acidolysis). Then, they were subjected to an oxygen delignification stage. The 16,9 kappa number pulp resulted in higher levels of non-condensed lignin structures by the acidolysis method, higher syringyl/vanillin ratios (S/V) by the nitrobenzene and copper oxide methods and better performance in the oxygen delignification stage. The different methods allowed to differ the residual lignin pulps with kappa number 14,5 and 16,9, and the nitrobenzene oxidation method showed the highest sensitiveness in this study results.

Primate Pulpal Healing after Exposure and TheraCal Application

Aim: The purpose of this in vivo study was to compare the effectiveness of a new light cured resin based dicalcium/tricalcium silicate pulp capping material (TheraCal LC, Bisco), pure Portland cement, resin based calcium hydroxide or glass ionomer in the healing of bacterially contaminated primate pulps. Study design: The experiment required four primates each having 12 teeth prepared with buccal penetrations into the pulpal tissues with an exposure of approximately 1.0 mm. The exposed pulps of the primate teeth were covered with cotton pellets soaked in a bacterial mixture consisting of microorganisms normally found in human pulpal abscesses. After removal of the pellet, hemostasis was obtained and the pulp capping agents applied. The light cured resin based pulp capping material (TheraCal LC) was applied to the pulpal tissue of twelve teeth with a needle tip syringe and light cured for 15 seconds. Pure Portland cement mixed with a 2% Chlorhexidine solution was placed on the exposed pulpal tissues of another twelve teeth. Twelve additional teeth had a base of GIC applied (Triage, Fuji VII GC America) and another twelve had a pulp cap with VLC DYCAL (Dentsply), a light cured calcium hydroxide resin based material. The pulp capping bases were then covered with a RMGI (Fuji II LC GC America). The tissue samples were collected at 4 weeks. The samples were deminerilized, sectioned, stained and histologically graded. Results: There were no statistically significant differences between the groups in regard to pulpal inflammation (H= 0.679, P=1.00). However, both the Portland cement and light cured TheraCal LC groups had significantly more frequent hard tissue bridge formation at 28 days than the GIC and VLC Dycal groups (H= 11.989, P=0.009). The measured thickness of the hard tissue bridges with the pure Portland and light cured TheraCal LC groups were statistically greater than that of the other two groups (H= 15.849, P=0.002). In addition, the occurrence of pulpal necrosis was greater with the GIC group than the others. Four premolars, one each treated according to the protocols were analyzed with a microCT machine. The premolar treated with the light cured TheraCal LC demonstrated a complete hard tissue bridge. The premolar treated with the GIC did not show a complete hard tissue bridge while the premolar treated with VLC Dycal had an incomplete bridge. The pure Portland with Chlorhexidine mixture created extensive hard tissue bridging.Conclusion: TheraCal LC applied to primate pulps created dentin bridges and mild inflammation acceptable for pulp capping.

Remoção de cromo de resíduos de curtumes por argilitos da formação Corumbataí - SP

The tanning wastes are characterized to be significant sources of pollution in the hydrosphere when non adjusted or disposed adequated form. That happens because this industry type uses the chromium to tan hides, and this element is present in discharges concentrations in final wastes, characterizing this waste type as dangerous, according to the Associação Brasileira de Normas Técnicas, através da Norma Brasileira 10.004 de 2004. Due to this, the research proposes a form to reduction chromium of the tanning wastes through the process of adsorption. For that were used mining-wastes of Corumbataí Formation clays, material commonly used in the production of ceramic products in Rio Claro (SP). They were accomplished laboratory essays that involved the preparation of different clays pulps and subsequent mixture of these with the tanning wastes, maintaining them under different mixing times and adsorption contacts. After the separation of the mixtures, the leached were chemically analyzed and it was seen the efficiency of chromium reduction and your relationship with the variation of different times of contact clays/wastes and different grain sizes used in the pulps preparation.

Produção de polpa solúvel a partir de Eucalyptus urograndis

The wood of the gender Eucalyptus occupies a prominence place in relation to other cellulose sources, due to its chemical composition, its low cost, abundance and availability. The dissolving pulp obtaining occurs basically starting from three stages: prehydrolysis of the wood following by cooking and finally by the bleaching process. In the dissolving pulp production is necessary a pretreatment stage for the hemicelluloses removal. Among the chemical cooking processes, the Kraft process is the most used for cellulosic pulps production starting from eucalyptus, in the additive presence or not. The anthraquinone uses in the pulping process has as main purposes increasing the delignification rate as well as protecting the pulp regarding the degradation of the polysaccharide chains. The ECF bleaching process consists of the purification of the pulp through bleaching agents, being excepted the elementary chlorine. The dissolving pulp is a pulp of high a-cellulose content and purity destined to the cellulose derivatives production as carboxymethyl cellulose, nitrocellulose and microcrystalline cellulose. The production of a certain product, as well as its final application, is determined by the chemical properties of the pulp. The present work had as purpose producing cellulosic pulp with kappa number around 9 destined to the production of dissolving pulp in way to evaluate the use of the anthraquinone (AQ) in the Kraft process according to the chemical properties of the obtained pulps. It has been still intended developing an effective technology of bleaching for the high purity and quality dissolving pulp production. The prehydrolysis was accomplished in laboratory rotational autoclave for 30 minutes at 170ºC in the water:wood rate 3,5:1 (L:kg). The Kraft/AQ pulping were accomplished in laboratory rotational autoclave being initially modified the active alkali load (10, 13, 16 and 19%) at sulfidity of 25% ...

Avaliação da atividade antioxidante, fotoprotetora e antiglicação dos extratos de folhas e frutos de espécies da família Annonaceae

Pós-graduação em Biociências - FCLAS

Aproveitamento de sementes de abóboras (Cucurbita sp) como fonte alimentar

Brazil processes much of its fruit by producing natural juices, candy preserves, extracts and pulps; however, almost 60% of their total weight derives from peels, leaves and seeds. As a result, the emphasis lies most strongly on the use of waste, especially waste that is not commonly used by the food industry or by consumers. The use of seeds would increase the viable sources of raw materials, lower operating costs of industries and would promote the development of new food products, since they are our main sources of protein, fat, fiber, functional compounds, vitamins and minerals salts. This paper presents alternatives for the use of pumpkin seeds (Cucurbita sp), which are often underutilized or discarded. It also demonstrates the bioactive and anti-nutritional compounds and their health effects.

Immediate human pulp response to ethanol-wet bonding technique

To evaluate the short-term response of human pulps to ethanol-wet bonding technique. Methods Deep class V cavities were prepared on 17 sound premolars and divided into three groups. After acid-etching, the cavities from groups 1 (G1) and 2 (G2) were filled with 100% ethanol or distilled water, respectively, for 60 s before the application of Single Bond 2. In group 3 (G3, control), the cavity floor was lined with calcium hydroxide before etching and bonding. All cavities were restored with resin composite. Two teeth were used as intact control. The teeth were extracted 48 h after the clinical procedures. From each tooth serial sections were obtained and stained with haematoxylin and eosin (H/E) and Masson's trichrome. Bacteria microleakage was assessed using Brown & Brenn. All sections were blindly evaluated for five histological features. Results Mean remaining dentine thickness was 463 ± 65 μm (G1); 425 ± 184 μm (G2); and 348 ± 194 μm (G3). Similar pulp reactions followed ethanol- or water-wet bonding techniques. Slight inflammatory responses and disruption of the odontoblast layer related to the cavity floor were seen in all groups. Stained bacteria were not detected in any cavities. Normal pulp tissue was observed in G3 except for one case. Conclusions After 48 h, ethanol-wet bonding does not increase pulpal damage compared to water-wet bonding technique. Clinical significance Ethanol-wet bonding may increase resin-dentine bond durability. This study reported the in vivo response of human pulp tissue when 100% ethanol was applied previously to an etch-and-rinse simplified adhesive system.

Remodeling of cortical and corticocancellous fresh-frozen allogeneic block bone grafts - a radiographic and histomorphometric comparison to autologous bone grafts

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aditivos alternativos aos antibióticos promotores de crescimento no desempenho de frangos de corte sob desafio sanitário

Pós-graduação em Zootecnia - FCAV

Caracterização do groundnut ringspot virus (grsv) e seu vetor (Frankliniella schultzei) em melancia

Pós-graduação em Agronomia (Proteção de Plantas) - FCA

Caracterização Físico-Química de Polpas de Frutas do Bioma Amazônia

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação dos parâmetros físico-químicos e estabilidade de compostos bioativos em óleos de polpa e amêndoa de frutos amazônicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sintomas de deficiências de macronutrientes em melancia

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Surgical Treatment of Severe Frontal Bone Fracture

Craniofacial trauma can lead to several complications. The combined fractures of anterior and posterior walls of the frontal bone are almost always followed by lesions in nasofrontal orifices and disruption of nasofrontal ostia or ducts, a significant factor for the development of early and late complications after sinus fractures. This article reports a case of trauma patient, who underwent neurological evaluation and at first showed good general condition. Computed tomography noted fracture of the anterior and posterior walls of the frontal sinus and small foci of pneumocephalus in the cerebral cortex. The patient was monitored periodically and 9 days after trauma showed increased areas of pneumocephalus in prefrontal cortex, cerebrospinal fluid draining, and large dura mater lesion, with signs of necrosis and inflammation (meningitis). The necrotic tissues were removed, and dura mater was repaired through the approximation with resorbable wire polyglactin 910 5-0, oxidized cellulose application, and bonding with human fibrin sealant (fibrinogen, thrombin, and calcium chloride). Sinusectomy, frontal sinus, and nasofrontal duct obliteration with pedicled pericranium flap were performed. Tomographically, a reanatomization was noted in frontal region, and a 12-month follow-up showed no complication. The use of fibrin glue to repair dura mater lacerations, as well as the pedicle pericranium flap for frontal sinus and nasofrontal duct obliteration, is an efficient method for treating fractures of the frontal bone.

Malignant syphilis in an immunocompetent female patient

Malignant syphilis is an uncommon manifestation of secondary syphilis, in which necrotic lesions may be associated with systemic signs and symptoms. Generally it occurs in an immunosuppressed patient, mainly HIV-infected, but might be observed on those who have normal immune response. Since there is an exponential increase in the number of syphilis cases, more diagnoses of malignant syphilis must be expected. We report a case in an immunocompetent female patient.