A Quality Assessment of Titanium Castings Produced in an Experimental Short-Heating-Cycle Investment

The aim of this study was to evaluate the quality of casting produced in an experimental short-term heating-cycle investment. Thus, reaction layer and castability of titanium casting using an experimental spinel-based investment (VR) with short heating cycle were compared with the commercial short-heating-cycle spinel-based investment Trinell (TR), the silica-phosphate-based investment Rematitan Plus ( RP), and the conventional spinel-based investment Rematitan Ultra (RU). VR has polymeric fibers added to inorganic particles. Reaction layer assessments were carried out using Vickers hardness and elemental analysis using dispersive X-ray microanalysis (EDX). Mesh patterns were used for castability test, and powder characterization was made by scanning electron microscopy (SEM). Hardness evaluation showed no difference among the investments between 100 and 200 mu m. The most important contaminant element for VR, TR, and RU was oxygen. Higher levels of mold filling were found for TR, VR, and RU compared with that obtained with RP. The quality of castings, characterized by means of the assessments of reaction layer and castability, made from the VR was similar to the commercial investments TR and RU but superior to the RP.

Delaunay Tetrahedralization of the Heart Based on Integration of Open Source Codes

The Finite Element Method (FEM) is a way of numerical solution applied in different areas, as simulations used in studies to improve cardiac ablation procedures. For this purpose, the meshes should have the same size and histological features of the focused structures. Some methods and tools used to generate tetrahedral meshes are limited mainly by the use conditions. In this paper, the integration of Open Source Softwares is presented as an alternative to solid modeling and automatic mesh generation. To demonstrate its efficiency, the cardiac structures were considered as a first application context: atriums, ventricles, valves, arteries and pericardium. The proposed method is feasible to obtain refined meshes in an acceptable time and with the required quality for simulations using FEM.

Impact of Quantity of Resin, C-factor, and Geometry on Resin Composite Polymerization Shrinkage Stress in Class V Restorations

Objective: This study evaluated the effect of quantity of resin composite, C-factor, and geometry in Class V restorations on shrinkage stress after bulk fill insertion of resin using two-dimensional finite element analysis.Methods: An image of a buccolingual longitudinal plane in the middle of an upper first premolar and supporting tissues was used for modeling 10 groups: cylindrical cavity, erosion, and abfraction lesions with the same C-factor (1.57), a second cylindrical cavity and abfraction lesion with the same quantity of resin (QR) as the erosion lesion, and then all repeated with a bevel on the occlusal cavosurface angle. The 10 groups were imported into Ansys 13.0 for two-dimensional finite element analysis. The mesh was built with 30,000 triangle and square elements of 0.1 mm in length for all the models. All materials were considered isotropic, homogeneous, elastic, and linear, and the resin composite shrinkage was simulated by thermal analogy. The maximum principal (MPS) and von Mises stresses (VMS) were analyzed for comparing the behavior of the groups.Results: Different values of angles for the cavosurface margin in enamel and dentin were obtained for all groups and the higher the angle, the lower the stress concentration. When the groups with the same C-factor and QR were compared, the erosion shape cavity showed the highest MPS and VMS values, and abfraction shape, the lowest. A cavosurface bevel decreased the stress values on the occlusal margin. The geometry factor overcame the effects of C-factor and QR in some situations.Conclusion: Within the limitations of the current methodology, it is possible to conclude that the combination of all variables studied influences the stress, but the geometry is the most important factor to be considered by the operator.

Analysis of the Stresses in Corrugated Sheets under Bending

This paper presents three different numerical models for the evaluation of the stresses in corrugated sheets under bending. Regarding the numerical simulations different approaches can be considered, i.e., a elastic linear analysis or a physical nonlinear analysis, that considers criteria to fail for the sheet material. Moreover, the construction of the finite element mesh can be used shell elements or solid elements. The choice of each finite element must be made from the consideration of their representativity before behavior to be simulated. Thus, the numerical modelling in this manuscript was performed from the three-dimensional models using the SAP2000Nonlinear software, version 7.42, which has as base the finite elements method (FEM). It was considered shell elements in the build the mesh of finite elements and an analysis of type elastic linear in this case. Five mm thick sheets were evaluated considering three different longitudinal dimensions (spans), i.e., 1100 mm, 1530 mm and 1830 mm. The applied load to the models was 2500 N/m and it was verified that the spans of support of sheets have a significant influence on the results of stresses. The sheets with larger spans present larger stresses for the same applied load. The most intense values of tension occur in the troughs (low waves) of the sheets, on the lower surface, while the most intense values of compression occur in the crests (high waves), on the upper surface of the sheet. The flanks, which are the parts among the troughs and crests of the sheets, are submitted to low levels of stresses. The numeric results of the stresses showed a good agreement with the results obtained from other researchers(3) and these results can be used to predict the behavior of corrugated sheets under bending.

Chemical Modification of Palm Fibres Surface with Zirconium Oxychloride

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aplicação de água ozonizada como agente sanitizante durante o processamento de café arábica

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Produção e qualidade do biogás gerado com os dejetos de diferentes espécies animais

Pós-graduação em Zootecnia - FCAV

Heart rate variability in children with type 1 diabetes mellitus

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito de reagentes de branqueamento na classificação e refinação de polpa de eucalipto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phosphorus reduction by sifting fish waste meal

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação espaço-temporal da distribuição de fósforo na água e nos sedimentos de fundo das sub-bacias dos rios Cuiabá e São Lourenço e em algumas baias do Pantanal Matogrossense

Pós-graduação em Química - IQ

Modeling of multiple cracks in reinforced concrete members using solid finite elements with high aspect ratio

This paper presents a new technique to model interfaces by means of degenerated solid finite elements, i.e., elements with a very high aspect ratio, with the smallest dimension corresponding to the thickness of the interfaces. It is shown that, as the aspect ratio increases, the element strains also increase, approaching the kinematics of the strong discontinuity. A tensile damage constitutive relation between strains and stresses is proposed to describe the nonlinear behavior of the interfaces associated with crack opening. To represent crack propagation, couples of triangular interface elements are introduced in between all regular (bulk) elements of the original mesh. With this technique the analyses can be performed integrally in the context of the continuum mechanics and complex crack patterns involving multiple cracks can be simulated without the need of tracking algorithms. Numerical tests are performed to show the applicability of the proposed technique, studding also aspects related to mesh objectivity.

Suplementação de vitamina A em dietas para Kinguios (Carassius auratus)

Vitamin A is important to the proper development and functioning of the body, appearing in several metabolic functions. This experiment was conducted with aim evaluate to the vitamin A supplementation in diets for Goldfish Carassius auratus. The experimental was completely randomized with six treatments (0, 2.000, 4.000, 8.000, 16.000 and 32.000 IU of vitamin A kg(-1) diet) with four repetitions into 24 experimental cages, with capacity for 150 liters useful volume, made of mesh shading, installed inside a masonry circular tank with a capacity of 25 m(3) of water. 192 fish with an average initial weight of 6.66 +/- 0.57 g and initial length of 7.30 +/- 0.33 cm, feed at 8h, 11h, 14h and 17h at satiety were used. Evaluated the effects on productive performance and intensity of yellow-red coloring of the skin of the fish were. The Linear Response Plateau analysis of weight gain and length total, feed conversion and daily growth rate versus vitamin A requirement estimate showed 2,624, 2,385 and 2,358, 4,381 and 2,866 IU of vitamin A per kg diet, respectively. The data indicated that this vitamin has little or no influence on the intensity of the skin color of the Goldfish.

Dependência espacial da estabilidade de agregados e matéria orgânica do solo em cambissolo sob cultivo de cana de açucar

The soil management system can modify the natural distribution of the soil attributes and, consequently, the variability of the soil aggregation and organic matter content. Thus, the aim of this work was to evaluate the aggregate stability and organic matter content spatial distribution on a Haplic Cambisol under sugar cane cultivation in the Southern Amazonas State, Brazil. A 70 x 70 m square mesh, with regular 10 meters intervals, was designed over the cultivation area, resulting in 64 sample points. Soil blocks with preserved structure were collected at 0.0-0.2 m depth in order to analyze the aggregate stability and organic matter content. The data were submitted to the descriptive and geostatistical analysis. The soil attributes presented a spatial dependence structure and the greater range was observed for the mean weighted diameter and aggregate class <1.00 mm. Also, there is a spatial relation among the mean geometric diameter, mean weighted diameter and aggregate classes (>2.00 and 2.00-1.00 mm).

Análise de uma câmara de combustão em escala piloto através de fluidodinâmica computacional

This work aims to examine, the behavior of a combustion chamber in pilot scale, coupled to a regenerative burner. The objective is to obtain a computational domain capable of supporting a simulation of conventional combustion and flameless combustion regimes. The objective is to obtain independence of mesh, analysis of the velocity fields of the fluid within the chamber, temperature and concentration profiles of the species emitted during the combustion process