Caracterização físico-mecânica de elementos estruturais roliços perfilados de Amaru

The study of physical and mechanical properties of wood is essential for its structural use and it is of great importance to the construction industry. Thus, this study aimed to determine the physical and mechanical properties of the wood Amaru - a hybrid of Eucalyptus, developed by Plantar Projects and Forest Products Ltda. In order to determine the properties of Amaru, round samples were used, which were provided to the Laboratory of Wood and Wooden Structures of the School of Engineering of São Carlos, University of São Paulo - LaMEM / EESC / USP. For the characterization of the physical properties, the apparent specific gravity and moisture content of the samples were determined. To the mechanical characterization, the following properties were evaluated: strength and stiffness in compression, strength and stiffness in bending, shear and tension. The procedures of the tests performed in this study were done according to the recommendations of the Brazilian Wood Standard ABNT NBR 7190:1997. The specimen used were confectioned in actual dimensions, according to as those used in the construction system proposed by Plantar. The results obtained from the tests performed showed that the mechanical properties approached the values proposed by the Wood Standard NBR 7190. The visual grading was important to provide a primary idea about the failure modes to be obtained from the tests performed. The bending test showed the modulus of elasticity (MOE) and Modulus of Rupture (MOR), which resulted in 15822 MPa and 101,7 MPa, respectively. The compression test resulted in values Ec0,m and fc0, 15698 MPa and 50,7 MPa. The tensile strength (ft0) of this hybrid was calculated and its value obtained was 60,8 MPa. The shear strength (fv0) was 8,2 MPa. The results obtained from the tests are the basis for engineers and architects to design structures using wood species Amaru

Análise dos fatores de desempenho do ENADE: estudo parao curso de engenharia de produção mecânica

This work has the propose to discuss the National Examination Performance of students for the course in Production Engineering , from 2005 up to 2011, subsidies are shown how this came about assessment and how the course has been evaluated in recent years . Compares higher education from public and private universities in Brazil and is also discussed how important a good performance in the exam. Qualitative and quantitative surveys were conducted at different times that the work that enables a critical analysis of the examination , the institution and also the students themselves , so the list is the main motivators for the exam and also what should be done to obtaining good results in academic performance. Motivators for the exam has highlighted its importance is paramount and the consent of all involved from the beginning of the course to ensure that the examination is compulsory for all graduates of undergraduate manufacturing engineering in Brazil

Viabilidade técnica e econômica na utilização de um sistema fotovoltaico para alimentação de luminárias LED na Faculdade de Engenharia do Campus de Guaratinguetá SP

Solar energy can be considered the largest source of energy available on earth and has attracted in recent decades, attention and interest for its rational use. The use of energy sources in a sustainable way is essential to the survival of future generations, due to the scarcity of natural resources and their exploitation in a disorderly way. This academic work aims to bring a possible alternative to reduce the consumption of eletrical energy, at the University of Engineering – Campus of Guaratinguetá, through the use of a photovoltaic system interconnected to the LED bulbs. For this, the necessary data for the design of the photovoltaic system componentes and their acquisition costs were obtained and three differents configurations were developed to choose the one that bests fits the studied case, considering the return time of the initial investment (payback)

Flexão e análise dinâmico-mecânica de compósitos 5HS e NCF com resina epóxi monocomponente produzidos por RTM

In order to study resin distribution and homogeneity of composite laminates manufactured by RTM, it was used CYCOM 890 monolithic toughened epoxy as a matrix with two different configurations of intermediated modulus (IM) carbon fibers: Satin Weave (5HS) and non crimp fabric (NCF). The injection parameters were defined based on Thermo Gravimetric Analysis (TG), Differential Scanning Calorimetry (DSC) and rheological analysis. After processing the material, the resin/fiber impregnation was studied using ultrasonic test, Thermo Gravimetric Analysis, Differential Scanning Calorimetry, Dynamic Mechanical Analysis (DMA) and flexural tests. Therefore, it was able to observe an internal residual stress during the cooling process in both laminates, higher in the composite using NCF fabric due to the lack of symmetry, although a good proportion of fiber/matrix has been verified by the lower values of flexural modulus deviation. The DMA enabled the visualization of glass transition and its association with the inter and intra molecular interaction and movement, in which the NCF composite presented better permeability due to the lowest temperature of glass transition, when compared to the Satin Weave composite

Estudo dos fatores de virulência e resistência à oxacilina em Staphylococcus spp. isolados de aspirado traqueal de pacientes em ventilação mecânica internados em UTI

Patients that are mechanically ventilated in ICUs are constantly exposed to different pathogens, which present multiantibiotic resistance. Among these microorganisms, is MRSA (Meticillin-Resistant Staphylococcus aureus) considered to be a therapeutic challenge due to its resistance to β-lactam antibiotics. Therefore, this study proposed to identify species of Staphylococcus spp. isolated from mechanically ventilated patients in ICU, the gene mecA detection and the genes of the enterotoxins A (sea), B (seb), C (sec-1) and D (sed) in samples of S. aureus, as well as the phenotypic resistance determination to oxacillin using the disc-diffusion method with discs of oxacillin and cefoxitin. The samples collection occurred during in a period of 19 months, obtaining samples from 232 patients. A percentage of 39% (70) of Gram-positive cocci were found; which 82,8% (58) were identified as Staphylococcus spp,. among these, 75,8% (44) corresponded to S. aureus species and 47,7% were identified as MRSA. It was found resistance to both drugs in 31,8% of the S. aureus samples, 16 (36,3%) had the gene sea and 11 (25%) had the sec-1 gene. Among the coagulase-negative staphylococci obtained, the species most found was S. epidermidis, corresponding to 43% (6). The results revealed that one of the most important etiologic agents of VAP amid the Gram-positive cocci is the species S. aureus, with special attention to MRSA. The presence of enterotoxins genes in S. aureus did not showed determinant role in VAP, but the presence of these superantigens can contribute worsening the patient’s prognosis, since they are associated with intense inflammatory response

Efeito do tratamento alcalino da fibra na resistência mecânica do compósito epóxi/capim-sapê

Due to growing concerns for reducing environmental damage caused by the use of non-renewable raw materials, there is a growing demand for research related to aggregate technology with environmental preservation. Thus, the use of non-renewable materials and less aggressive materials has been gaining attention. About composite materials, the exchange of synthetic fibers by natural fibers, especially vegetable fiber as reinforcement, has been increasing, due to its physical-chemical properties such as mechanical strength, nontoxic, low cost, low density, processing flexibility, non-abrasive to the process equipment, requiring simple surface treatments, etc. This objective was to process composites reinforced with long fibers of sapegrass in epoxy matrix and characterize the composites through mechanical tests. Three groups of composites were prepared according to the treatment received by the reinforcement: without treatment, alkali treatment at concentration of 5% w/v and alkali treatment at 10% w/v concentration. The materials were analyzed by tensile and flexural, and tests also optical microscopy and scanning electron microscopy (SEM). The results were statistically analyzed. As the main result, the alkali treatment of 5% in the sapegrass fibers increases the tensile and flexural strength, as a consequence of the improve adhesion between matrix and reinforcement

Decisão making or buying: uma aplicação em células de manufatura de uma indústria de produção mecânica

In order to maintain the competitiveness the companies seek for cost reduction and resource optimization. A product or service price is calculated considering direct and indirect costs involved in its fabrication, which means that if an intern indirect process is optimized, the final price of the product is also reduced and becomes more interesting to the final costumer. Considering this reasoning, the companies must evaluate each of their processes and optimize them. It is common to outsource intern products manufacturing as a cost reduction strategy, nevertheless when there are already resources and capability to produce the own goods, it becomes necessary to evaluate the economic gain that each strategy - make or buy - generates. This paper aims to evaluate the necessary support to take a decision regarding making or buying in a production cell of hoses based in the value of economic cost, system cost and decision process

Transformada de Fourier: teoria como base para aplicações em mecânica celeste

Pós-graduação em Matemática Universitária - IGCE

Sistema de avaliação e tratamento da coluna lombar com o uso de tração mecânica

Pós-graduação em Engenharia Mecânica - FEG

Identificação de patógenos da cavidade bucal no lavado broncoalveolar de pacientes sob ventilação mecânica

Pós-graduação em Odontologia Restauradora - ICT

Resistência à flexão em porcelana feldspática: efeito da ciclagem mecânica e limite de fadiga pelo método escada

This study evaluated the fatigue limit (FL) by the staircase method and the effect of mechanical cycling on the flexural strength (FS) of Duceragold feldspathic porcelain. Specimens (25 x 5 x 2 mm) were made according to manufacturer’s directions and submitted to three-point flexural strength test (n = 10). To determine FL (n = 30; 10,000 cycles; 2 Hz), an initial loading of 60% of the FS and an incremental loading (step) of 3% of the FS were used. Data were analyzed by Anova and Tukey´s test (p < 0.05). Although the proposed cycles have not reduced FS significantly, fractography analysis showed striation, characteristic signs of mechanical fatigue.

Comportamento biomecânico do sistema prótese/implante em região anterior de maxila: análise pelo método de ciclagem mecânica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Energia mecânica, energia térmica e moagem na extrusão de alimentos para cães e gatos

Pós-graduação em Medicina Veterinária - FCAV