Degradabilidade do amido de grãos secos e ensilados de híbridos de milho com textura dura e dentada em função do grau de moagem

This research evaluated corn grains with flint and dent texture (ensiled high-moisture or dried), submitted to grinding degrees, using the in situ ruminal degradation technique. Three rumen canulated adult sheeps were used in a complete randomized design, using a factorial outline 2 x 2 x 3, with two corn hybrids (flint and dent texture), two conservation methods (ensiled high-moisture and dry) and three grinding degress (whole, coarsely and finely ground, corresponding to the sieve of 12; 10 and 8 mm). Starch soluble fraction (A) of the dent hybrid ensiled corn grains was greater comparing to the dry materials and in both conservation forms this fraction was reduced in the flint texture hybrid, while the insoluble fraction potentially degradable (B) the opposite occurred. The degradation potential was higher in grains ensiled in two textures. The ensiled allowed more starch effective degradation in relation to dry grain in two textures and the grains dent texture hybrid also increased such degradation in both conservation methods. The dent texture and the ensiled high-moisture grains proved the best option considering the starch degradability. Regardless of the conservation forms, the grains of corn hybrid flint texture should be finely ground, for providing higher ruminal degradation, while for the dent texture hybrid, the coarsely and whole grinding are the most suitable for ensiled and dry grain, respectively.

Pré-hidrólise ácida de bagaço de cana-de-açúcar e sua caracterização físico-química

The biomass resulting from processing sugarcane bagasse has been considered a source of cellulose with the potential production of bio-fuels. This lignocellulose can be processed into ethanol since is hydrolyzed by chemical processes (acids) or biotechnology (enzymes) which generate sugars suit for fermentation. This study had the objective to utilize physical and chemical pre-treatment processes for prehydrolysis of sugarcane bagasse. The experimental treatment was adjusted at a factor of 4 X 2, by the combination of pre-hydrolysis timing (15, 30, 45 and 60 minutes) and sulfuric acid concentrations (7.0% and 9.0%) which was incubated at a temperature of 121° C in an autoclave. The treatment data was subjected to analysis of the variance and averages which were compared using the Tukey test with a probability of 5%. The results obtained showed that through pretreatment acid applied on the lignocellulose material, there was a significant break from the substrate fibers like cellulose, hemicellulose and lignin.

Avaliação do processo de hidrólise enzimática para obtenção de açúcares a partir de gengibre (Zingiber officinale)

Ginger is a starchy tubers prized for their chemical components. In the production of any kinds of beverages has been added to the extract of ginger. However, in view of the high starch content, a possibility of further development of the agribusiness sector this would be the hydrolysis tuberous rhizomes disqualified for export in order to obtain hydrolysates that would be used in the preparation of fermented beverages. This work aimed to evaluate the production of sugar from rhizomes of ginger. Two α-amylase enzymes were tested in the stage of liquefaction (Liquozyme Supra (T1) and Termamyl 2X (T2)), as well as the effect of time of action of amyloglucosidase (AMG 300L). The hydrolysates were analyzed in liquid chromatography (HPLC) and was also carried out the mass balance of the processes. The results showed higher hydrolysis of starch in the treatment that used Liquozyme Supra in liquefaction. The action time of 18 hours of AMG 300L hydrolyzate which gave an 98% of its chemical components was glucose.

Efeito prebiótico de xilo-oligossacarídeos produzidos a partir da hemicelulose de bagaço de cana-de-açúcar utilizando extração alcalina e hidrólise de xilanases fúngicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Pré-tratamento do bagaço de cana-de-açúcar, hidrólise e sua caracterização química e estrutural, visando a produção de etanol de segunda geração

Pós-graduação em Biotecnologia - IQ

Construção de gráficos de funções polinomiais de grau 3

Pós-graduação em Matemática em Rede Nacional - IBILCE

Produção de amilases de Rhizopus microsporus var. oligosporus e hidrólise enzimática do bagaço de mandioca visando a produção de etanol por Saccharomyces cerevisiae

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do grau de modernização e mecanização nas obras de construção civil: estudo de caso - cidade de Lorena

This paper had as emphasis the study of the mechanization and modernization of the construction job sites of the city of Lorena located in the Vale do Paraíba, São Paulo. From the literature review on this topic, it was possible to understand the main causes of the delay in the job sites relating to the new technology available. The research on the history of construction and equipment evolution, along with interviews with workers, engineers and architects, it was possible to analyze the current situation. One of the main intentions of this study was to propose guidelines for the modernization of the construction sites

Determinação comparativa do grau de deformação plástica aplicado a componentes obtidos por conformação

The manufacturing process of components of Pressure Vessels has a great importance in the efficiency during the operation and life cycle of the equipment. Taking this into account, the objective of this dissertation was to analyze the methods to determine the strain rate in formed components by measuring the components themselves, and posterior results comparison with the values found in manufacturing standards of Pressure vessels. In this study the whole manufacturing process of a component from a pressure vessel, known as Head or End, was accompanied. Using the methodology obtained from literatures it was possible to execute the relative and logarithmic deformation measurements of these components and compare with the obtained results by means of equations presented in the Standards as AD-Merkblatt and ASME (for pressure vessels). The found results were also compared with the logarithmic methodology, taking into account the deformation of the empirical mesh and the thickness of the components studied. It is possible to conclude from this study that despite the existence of empirical methods of measurement of strain rate in components plastically formed, it is recommended the adoption in all situation of the component manufacturing standard. It can be noticed and explained during the development of this study and through the results found