Effect of handpiece tip design on the cutting efficiency of an air abrasion system

Purpose : the aim of this study was to evaluate the effect of nozzle angle and tip diameter on the cutting efficiency of an air abrasion system. Materials and Methods: Thirty-six extracted human third molars were air-abraded with the PrepStar microabrasion machine using a handpiece with either 80degrees or 45degrees nozzle angles with 0.38 or 0.48 nun tip orifice diameters. The following parameters were held constant: abrasive particle size (27 mum), air pressure (80 psi), distance (2 mm.) and duration (15 seconds). The cutting efficiency was compared using enamel, dentin and cementum substrates. Width and depth of the cutting patterns were analyzed and measured using scanning electron micrographs. Results: Statistical analysis using three-way ANOVA and Duncan's Multiple Range test revealed that the width of the cuts was significantly greater when the cavities were prepared using the 45degrees nozzle angle. Significantly deeper cavities were produced with the 80degrees nozzle angle. The tip orifice of the nozzle influenced the cutting efficiency in softer substrates, dentin and cementum. Precise removal of hard tissue is best accomplished using the 80degrees angle nozzle tips for all types of tooth surfaces, enamel, dentin and cementum.

Comparison of direct digital and conventional imaging with Ekta Speed Plus and INSIGHT films for the detection of approximal caries

Purpose: To evaluate the accuracy of approximal caries detection comparing enhanced and unenhanced Sidexis CCD-based digital image with Ektaspeed Plus and INSIGHT films. Methods: Fifty-two extracted premolars were imaged under identical standardized geometric and exposure conditions. Four observers, using five points confidence scale, rated 104 approximal surfaces for the presence or absence of carious lesions by means of four image modalities: (1) observer enhanced; (2) unenhanced Sidexis displays; (3) E speed films and (4) F speed film. Histologic sections served as validating criterion for the presence and depth of carious lesions. Diagnostic accuracy was measured as the area beneath the ROC curve. Results: Mean ROC (receiver operating characteristic) curve areas for approximal surfaces were 0.865 (E speed), 0.856 (F speed), 0.816 (unenhanced Sidexis) and 0.776 (observer enhanced). There were no significant differences between unenhanced digital Sidexis and films. Observer enhanced Sidexis images exhibited a statistically significant lower diagnostic accuracy than the film images for two of the observers.

DECOMPOSITION RATES OF SPENT FUNGAL REFUSE OF ATTA-SEXDENS (HYMENOPTERA, FORMICIDAE) AND IMPLICATIONS FOR ESTIMATING FORAGE INTAKE BY LEAF-CUTTING ANTS

Using simulated ceramic refuse chambers, field decomposition studies were performed on the spent fungal refuse of the lead-cutting ant Atta sexdens rubropilosa. Refuse half life was estimated at 40 days, with complete decomposition at 100 days. These results suggest that the conversion-factor method used to estimate forage input into leaf-cutting ant colonies must be corrected for decomposition, or serious estimation errors will occur.

Effects of milling condition on the surface integrity of hot forged steel

This paper presents a study on the influence of milling condition on workpiece surface integrity focusing on hardness and roughness. The experimental work was carried out on a CNC machining center considering roughing and finishing operations. A 25 mm diameter endmill with two cemented carbide inserts coated with TiN layer were used for end milling operation. Low carbon alloyed steel Cr-Mo forged at 1200 degrees C was used as workpiece on the tests. Two kinds of workpiece conditions were considered, i.e. cur cooled after hot forging and normalized at 950 degrees C for 2 h. The results showed that finishing operation was able to significantly decrease the roughness by at least 46% without changing the hardness. on the other hand, roughing operation caused an increase in hardness statistically significant by about 6%. The machined surface presented deformed regions within feed marks, which directly affected the roughness. Surface finish behavior seems to correlate to the chip ratio given the decrease of 25% for roughing condition, which damaged the chip formation. The material removal rate for finishing operation 41% greater than roughing condition demonstrated to be favorable to the heat dissipation and minimized the effect on material hardness.

An evolutionary algorithm for the one-dimensional cutting stock problem

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Ventilation of the giant nests of Atta leaf-cutting ants: does underground circulating air enter the fungus chambers?

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Lagrangian relaxation approach to a coupled lot-sizing and cutting stock problem

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Trajectory of Water- and Fat-Soluble Dyes in the Grass-Cutting ant Atta capiguara (Hymenoptera, Formicidae): Evaluation of Infrabuccal Cavity, Post-Pharyngeal Glands and Gaster

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Experimental and theoretical study of workpiece temperature when end milling hardened steels using (TiAl)N-coated and PcBN-tipped tools

The present work shows an experimental and theoretical study on heat flow when end milling, at high-speed, hardened steels applied to moulds and dies. AISI H13 and AISI D2 steels were machined with two types of ball nose end mills: coated with (TiAl)N and tipped with PcBN. The workpiece geometry was designed to simulate tool-workpiece interaction in real situations found in mould industries, in which complex surfaces and thin walls are commonly machined. The compressed and cold air cooling systems were compared to dry machining Results indicated a relatively small temperature variation, with higher range when machining AISI D2 with PcBN-tipped end mill. All cooling systems used demonstrated good capacity to remove heat from the machined surface, especially the cold air. Compressed air was the most indicated to keep workpiece at relatively stable temperature. A theoretical model was also proposed to estimate the energy transferred to the workpiece (Q) and the average convection coefficient ((h) over bar) for the cooling systems used. The model used a FEM simulation and a steepest decent method to find the best values for both variables. (c) 2007 Elsevier B.V. All rights reserved.

Relationship Between Speed and Time in Running

The purpose of this study was to evaluate the effect of using different mathematical models to describe the relationship between treadmill running speed and time to exhaustion. All models generated a value for an aerobic parameter (critical speed; S(critical)). 35 university students performed 5-7 constant-speed 0%-slope treadmill tests at speeds that elicited exhaustion in similar to 3 min to similar to 10 min. Speed and time data were fitted using 3 models: (1) a 2-parameter hyperbolic model; (2) a 3-parameter hyperbolic model; and (3) a hybrid 3-parameter hyperbolic + exponential model. The 2-parameter model generated values for S(critical) (mean (+/- SD): 186 +/- 33 m.min(-1)) and anaerobic distance capacity (ADC; 251 +/- 122 m) with a high level of statistical certainty (i.e., with small SEEs). The 3-parameter models generated parameter estimates that were unrealistic in magnitude and/or associated with large SEEs and little statistical certainty. Therefore, it was concluded that, for the range of exercise durations used in the present study, the 2-parameter model is preferred because it provides a parsimonious description of the relationship between velocity and time to fatigue, and it produces parameters of known physiological significance, with excellent confidence.

Effect of juvenility on cutting propagation of red pitaya

Introduction. Pitaya (Hylocereus undatus) is an exotic fruit species little known in Brazil and which needs basic studies about plant nutrition, propagation and physiology. Emphasizing the co-existence of juvenile and adult stages in the pitaya canopy, the plant is generally propagated by cuttings. Materials and methods. A completely randomized design with four treatments and five replications was adopted. Each treatment was represented by the part of the canopy from which the cutting was taken ( upper, middle and lower cutting and cuttings from young plants). The following variables were registered: % cuttings with roots, % of live cuttings, root density, root diameter, root area, root length and root dry mass. Results were submitted to variance analyses, Tukey's test at 0.01 probability error and simple correlation analysis. Results and discussion. The results indicated that the position from which the cutting is taken had a quantitative effect on rooting formation of pitaya cuttings. Juvenile cuttings presented 35% more cuttings with roots than adult cuttings. Root density, root area, root length and root dry mass depended on juvenility, the highest results being registered for juvenile cuttings, independently of the variable. Conclusion. Juvenile and adult stages co-exist in the pitaya canopy. Juvenility is an important rooting factor for red pitaya cuttings.

High-speed video observations of positive ground flashes produced by intracloud lightning

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Expressed sequence tags from Atta laevigata and identification of candidate genes for the control of pest leaf-cutting ants.

Leafcutters are the highest evolved within Neotropical ants in the tribe Attini and model systems for studying caste formation, labor division and symbiosis with microorganisms. Some species of leafcutters are agricultural pests controlled by chemicals which affect other animals and accumulate in the environment. Aiming to provide genetic basis for the study of leafcutters and for the development of more specific and environmentally friendly methods for the control of pest leafcutters, we generated expressed sequence tag data from Atta laevigata, one of the pest ants with broad geographic distribution in South America. Results: The analysis of the expressed sequence tags allowed us to characterize 2,006 unique sequences in Atta laevigata. Sixteen of these genes had a high number of transcripts and are likely positively selected for high level of gene expression, being responsible for three basic biological functions: energy conservation through redox reactions in mitochondria; cytoskeleton and muscle structuring; regulation of gene expression and metabolism. Based on leafcutters lifestyle and reports of genes involved in key processes of other social insects, we identified 146 sequences potential targets for controlling pest leafcutters. The targets are responsible for antixenobiosis, development and longevity, immunity, resistance to pathogens, pheromone function, cell signaling, behavior, polysaccharide metabolism and arginine kynase activity. Conclusion: The generation and analysis of expressed sequence tags from Atta laevigata have provided important genetic basis for future studies on the biology of leaf-cutting ants and may contribute to the development of a more specific and environmentally friendly method for the control of agricultural pest leafcutters.

A pest is a pest is a pest? The dilemma of neotropical leaf-cutting ants: Keystone taxa of natural ecosystems

Leaf-cutting ants of the genera Acromyrmex and Atta are considered the principal polyphagous pests of the Neotropics. Although some members of these genera are of economic importance, have a broad geographic distribution, and are extremely good colonizers, others are endemic and closely interact with native ecosystems. Control is generally practiced against any colony, irrespective of its taxonomic status. Indiscriminate control coupled with habitat destruction threatens endemic species with extinction, and, through habitat simplification, favors other pest species. As nests of Atta are large, having several square meters of nest surface, the endemic taxa can be easily used as environmental indicators for natural ecosystems. Likewise, the pest species can be used to detect environmental disturbance. As these ants are keystone species and easily identified by nonspecialists, efforts should be made to integrate these into viable conservation programs.