Second Phase Precipitation in Ultrafine-grained Ferrite Steel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Application of acoustoelasticity to measure the stress generated by milling in ASTM A36 steel plates

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Sn(1-x)LaxO2 thin films deposited on AISI 304 stainless steel substrates

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Heat Treatment and Yb-Fiber Laser Welding of a Maraging Steel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

FATIGUE IN CUSTOM 465 STAINLESS STEEL FOR AERONAUTIC APPLICATION

This project was originated from the national aircraft industry requirements to reduce the use of coated materials with electroplated chromium or cadmium that produce waste, which is harmful to health or the environment. The selected material is a Custom 465 stainless steel used in the aeronautical field due to its high mechanical strength. Considering the load sustained by the wheel axis of the landing gear, the Custom 465 was tested in axial fatigue. The objective is to compare the behavior of the Custom 465 stainless steel with plated AISI 4340 steel coated with cadmium. Fractographic analysis was conducted using scanning electron microscopy. X-ray diffraction method was used to determine the residual stress field induced by shot peening.

Desenvolvimento de um computador de bordo para veículo Baja-SAE

The objective of this paper is show the development of an Eletronic Control Unit (ECU) for Baja-SAE vehicles from its requirements to final implementation. An ECU for Baja-SAE vehicles is made of electric and electronic circuits (appropriated to the hostile situations of an off-road competition) able to make important measurements for the running or stand-by vehicle performance. For this development, some concepts were studied: embedded electronics concepts (mainly microcontrollers and data acquisition circuits) and sensoring. Both the studies were made considering the off-road environment. After these initial studies, the elaboration of the basics hardware and software (under simulations) has begun, and this elaboration objectives maximum performance and low implementation cost. After the theorical studies, basic definition of the hardware and software’s architectures and simulations, the printed circuit boards (PCB) were made, as exhaustive tests in these boards for debugging and verify if the boards work well. Once the system was tested in the university, it ran into a regional Southeast competition in 2010, that definitely proved the efficiency of the whole system

Influências do Projeto Baja SAE no ensino da engenharia e no desenvolvimento do aluno

This work aims to show the importance of Baja SAE Project in engineering education, as well as the development of the student, being an outstanding tool for the engineering student has an education that meets the objectives of the pedagogical university and also the guidelines Ministry of Education curriculum for engineering courses. The Baja SAE Project provides the engineering students the chance to apply in practice the knowledge acquired in the classroom, to enhance their preparation for the labor market. The student becomes involved with a real case of project development, from concept design, detailed design and construction. The Baja SAE Project redefines the position of the student as an active element in the learning process engineering, leaving behind the simple condition of receiving information. Values procedures that provide students the opportunity to learn in contexts of professional practice, while offering the opportunity to contextualize the execution of a project. From an analysis to develop personal skills, Baja SAE Project has its own characteristics and essential for professional practice, however, not specific to the engineering course. For example, capacity for teamwork, communication skills written and oral, ethical behavior, critical, overview, entrepreneurial spirit, leadership, etc

Otimização do braço inferior da suspensão dianteira do veículo Baja utilizando o método dos elementos finitos

Mass reduction coupled with the mechanical performance in service has been the goal of many projects related to the transport area, considering the advantages that mass reduction can bring. However, make a simple material substitution without design a new geometry to corroborate for the best component performance, often makes the replacement unviable. In this study, it was investigated the advantages of replacing the prototype BAJA SAE front suspension lower arm of Equipe Piratas do Vale de BAJA SAE - Universidade Paulista, Campus Guaratinguetá, actually produced with steel, for a new component made of carbon fiber composite. The new geometry has been developed to provide the best possible performance for this component and your easy manufacturing. The study was done using the 3D modeling tools and computer simulations via finite element method. The first stage of this work consisted on calculation of the estimated maximum contact force tire / soil in a prototype landing after jump at one meter high, drop test in the laboratory with the current vehicle, current front suspension lower arm 3D modeling, finite element simulation and analysis of critical regions. After all current component analysis, a new geometry for the part in study was designed and simulated in order to reduce the component mass and provide a technological innovation using composite materials. With this work it was possible to obtain a theoretical component mass reduction of 25,15% maintaining the mechanical strength necessary for the appropriated component performance when incited

Análise dos efeitos das deformações estruturais sobre a transferência transversal de carga em um veículo do tipo fórmula SAE submetido a uma aceleração lateral constante

This paper studies the frame deformations on a formula SAE vehicle in steady-state cornering and its influence on the lateral load transfers and, consequently, on the tires normal loads due to the applied lateral load. For a vehicle with a perfect rigid frame, the vehicle mass, the position of the center of gravity and the suspensions are the only factors responsible for the load distribution between the tires. When the frame deformations are no longer negligible, the frame deformations affect the loaddistribution between the tires. The frame flexibility turns it able to behave as an additional set of springs to the suspension system, thus changing the behavior of the set. This paper describes howit happens and suggests ways to minimize this phenomenon

Análise de falhas por fadiga de alto ciclo em eixos de transmissão utilizando o método dos elementos finitos

This work presents a study that aims to validate the fatigue analyses developed on finite element commercial software, ANSYS Workbench. It was based on mechanical tests development of traction and hardness, to verify the mechanical properties of material that the shaft was manufactured (ABNT 1045 steel), it was developed bend test, with purpose to prove the confiability degree of computational analyses, obtaining the maximum stress in a work condition determined with 40 [kgf] of load applied, and at the end, was developed the fatigue test to obtain the number of cycles that the transmission shaft can support in a work condition with 8 [kgf] of load applied. The results obtained during the work present, have to be quite satisfactory with the theoretically expected

Avaliação dos mecanismos de endurecimentoda liga AISI 300M submetida a diferentes ciclos de transformações martensíticas

Pós-graduação em Engenharia Mecânica - FEG

Grinding process monitoring based on electromechanical impedance measurements

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Interaction between recrystallization and strain-induced precipitation in a high Nb- and N-bearing austenitic stainless steel: influence of the interpass time

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aplicação do método de impedância eletromecânica na detecção da queima no processo de retificação plana

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)