EVALUATION OF EUCALYPTUS KRAFT PULP LIGNIN THROUGH THE NITROBENZENE OXIDATION, COPPER OXIDE REDUCTION AND ACIDOLYSIS TECHNIQUES

This study aimed to evaluate the sensitiveness of the information obtained for the residual lignin from Eucalyptus grandis kraft pulps analyzed through the nitrobenzene oxidation, copper oxide (CuO) reduction and acidolysis techniques. The chips were cooked, resulting pulps of kappa number 14,5 and 16,9, respectively. Both lignins' pulps were evaluated through three methods (nitrobenzene oxidation, copper oxide oxidation and acidolysis). Then, they were subjected to an oxygen delignification stage. The 16,9 kappa number pulp resulted in higher levels of non-condensed lignin structures by the acidolysis method, higher syringyl/vanillin ratios (S/V) by the nitrobenzene and copper oxide methods and better performance in the oxygen delignification stage. The different methods allowed to differ the residual lignin pulps with kappa number 14,5 and 16,9, and the nitrobenzene oxidation method showed the highest sensitiveness in this study results.

Improved pretreatments applied to the sugarcane bagasse and release of lignin and hemicellulose from the cellulose-enriched fractions by sulfuric acid hydrolysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Zero-valent iron mediated degradation of ciprofloxacin - Assessment of adsorption, operational parameters and degradation products

The zero-valent iron (ZVI) mediated degradation of the antibiotic ciprofloxacin (CIP) was studied under oxic condition. Operational parameters such as ZVI concentration and initial pH value were evaluated. Increase of the ZVI concentration from 1 to 5 g L−1 resulted in a sharp increase of the observed pseudo-first order rate constant of CIP degradation, reaching a plateau at around 10 g L−1. The contribution of adsorption to the overall removal of CIP and dissolved organic carbon (DOC) was evaluated after a procedure of acidification to pH 2.5 with sulfuric acid and sonication for 2 min. Adsorption increased as pH increased, while degradation decreased, showing that adsorption is not important for degradation. Contribution of adsorption was much more important for DOC removal than for CIP. Degradation of CIP resulted in partial defluorination since the fluoride measured corresponded to 34% of the theoretical value after 120 min of reaction. Analysis by liquid chromatography coupled to mass spectrometry showed the presence of products of hydroxylation on both piperazine and quinolonic rings generating fluorinated and defluorinated compounds as well as a product of the piperazine ring cleavage.

On-line monitoring of electrochemical degradation of paracetamol through a biomimetic sensor

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Analysis of a microbial community associated with polychlorinated biphenyl degradation in anaerobic batch reactors

The degradation of polychlorinated biphenyls (PCBs) was investigated under fermentativemethanogenic conditions for up to 60 days in the presence of anaerobic biomass from a full-scale UASB reactor. The low methane yields in the PCBs-spiked batch reactors suggested that the biomass had an inhibitory effect on the methanogenic community. Reactors containing PCBs and co-substrates (ethanol/ sodium formate) exhibited substantial PCB reductions from 0.7 to 0.2 mg mL-1 . For the Bacteria domain, the PCBs-spiked reactors were grouped with the PCB-free reactors with a similarity of 55 %, which suggested the selection of a specific population in the presence of PCBs. Three genera of bacteria were found exclusively in the PCB-spiked reactors and were identified using pyrosequencing analysis, Sedimentibacter, Tissierela and Fusibacter. Interestingly, the Sedimentibacter, which was previously correlated with the reductive dechlorination of PCBs, had the highest relative abundance in the RCS-PCB (7.4 %) and RCS-PCB-PF (12.4 %) reactors. Thus, the anaerobic sludge from the UASB reactor contains bacteria from the Firmicutes phylum that are capable of degrading PCBs.

Characterization and thermal study of organic extracts of urban solid waste

The urban residues put in landfill of the city of Sa˜o Carlos-SP, Brazil, in 2004 represent 58.7 % of decomposed organic material. The aim of this research was to characterize samples of urban solid waste and its organic extracts targeting the use of this residue without damaging the environment. The curves were obtained in a nitrogen atmosphere, a heating rate of 20 C min-1 , the temperature of 30–600 C. In the original sample after humidity loss, an event occured concerning the water constitution in the TG curve with an endothermic peak in the DTA curve. There was a presence of inorganic residue in the ashes. The organic matter present in the USR sample disposed in the landfill is constituted by several polarity, organics compounds from the degradation of lignin, cellulose, lipids, and other materials which thermal stabilities are distinct. The hexane extract features in its constitution two fatty acids, stearic and triacontano´ic, which are nonpolar compounds originating from bacteria present in the residue. The acids groups in extract hexane also were evidenced by X-ray diffraction and FTIR.

In vitro comparison of the force degradation of orthodontic intraoral elastics from different compositions

The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) with internal diameter of 1/8", 3/16", 1/4" and 5/16". The elastics were randomly divided into 7 groups according to the time of the force measuring and immersed into distilled water at 37°C. To measure the force in each group, the elastics were stretched in six progressive increases of 100% of its internal diameter with the aid of a testing machine Emic and measured up to 72 hours. Data were analyzed with SPSS 16.0, using one-way analysis of variance (ANOVA). Results: Immediate force level of synthetic elastics was statistically higher than latex elastics in all strains, for the same size. However, the latex elastics mean forceslightly decreased over time, while the synthetic elastics presented an abrupt decrease. Conclusion: In view of these findings, Sudanese homemade alcoholic beverages cause oral epithelial atypical changes, which lead to oral precancerous and cancerous lesions. OEFC is a useful procedure for detection and assessment of oral ET.

In vitro comparison of the force degradation of orthodontic intramural elastic from different compositions

Introduction and Objective: The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) with internal diameter of 1/8”, 3/16”, 1/4” and 5/16”. The elastics were randomly divided into 7 groups according to the time of the force measuring and immersed into distilled water at 37°C. To measure the force in each group, the elastics were stretched in six progressive increases of 100% of its internal diameter with the aid of a testing machine Emic and measured up to 72 hours. Data were analyzed with SPSS 16.0, using one-way analysis of variance (ANOVA). Results: Immediate force level of synthetic elastics was statistically higher than latex elastics in all strains, for the same size. However, the latex elastics mean force slightly decreased over time, while the synthetic elastics presented an abrupt decrease. Conclusion: The synthetic elastic presented severe force degradation, jeopardizing the cost-benefit ratio, which indicates a higher replacement frequency. The latex elastic showed better mechanical performance in comparison to synthetic ones.

Aplicação em subdose do haloxyfop-methyl na aveia-preta

One of the major constraints to sustainable of the tillage is the rapid decomposition of dry the matter. One of the mechanisms known to facilitate this process is the interference in pathways of polymers of lignin from tests of application of low doses of herbicide based on the relation that higher the content of the lignin greater the resistance to degradation. With this purpose, the herbicide Verdict * R (haloxyfop-methyl) was used to verify the effect of low doses at the height of the plants, productivity of dry matter and in the metabolism of the lignin in plants of black oat. Preliminary tests in the greenhouse were realized for adjustments ​​to the best low doses to be applied in the definitive experiment in the production area. The results obtained were 24% of increase in productivity in the experiments conducted in greenhouse, from the application of 3.125g of the active ingredient of the haloxyfop-methyl per hectare, in this subdose no changes was observed in growth and content of lignin in plants of black oat. In the field, the concentration of 2.5g i. a. ha-1 of haloxyfop-methyl decreased in 9% the lignification rate without interfering with the height and productivity of the plants, this being favorable to the degradation rate of stubble tillage on outcome

Acúmulo de nutrientes e tempo de decomposição da palhada de espécies forrageiras em função de épocas de semeadura

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Surface degradation of lithium disilicate ceramic after immersion in acid and fluoride solutions

Purpose: To analyze whether immersion in sodium fluoride (NaF) solutions and/or common acidic beverages (test solutions) would affect the surface roughness or topography of lithium disilicate ceramic. Methods: 220 ceramic discs were divided into four groups, each of which was subdivided into five subgroups (n = 11). Control group discs were immersed in one of four test beverages for 4 hours daily or in artificial saliva for 21 days. Discs in the experimental groups were continuously immersed in 0.05% NaF, 0.2% NaF, or 1.23% acidulated phosphate fluoride (APF) gel for 12, 73, and 48 hours, respectively, followed by immersion in one of the four test beverages or artificial saliva. Vickers microhardness, surface roughness, scanning electron microscopy (SEM) associated with energy dispersive spectroscopy, and atomic force microscopy (AFM) assessments were made. Data were analyzed by nested analysis of variance (ANOVA) and Tukey's test (alpha = 0.05). Results: Immersion in the test solutions diminished the microhardness and increased the surface roughness of the discs. The test beverages promoted a significant reduction in the Vickers microhardness in the 0.05% and 0.2% NaF groups. The highest surface roughness results were observed in the 0.2% NaF and 1.23% APF groups, with similar findings by SEM and AFM. Acidic beverages affected the surface topography of lithium disilicate ceramic. Fluoride treatments may render the ceramic surface more susceptible to the chelating effect of acidic solutions.

Penetration of hydrogen peroxide and degradation rate of different bleaching products

This study's aim was to evaluate the degradation rate of hydrogen peroxide (H2O2) and to quantify its penetration in tooth structure, considering the residence time of bleaching products on the dental enamel. For this study, bovine teeth were randomly divided according to the bleaching product received: Opalescence Xtra Boost 38%, White Gold Office 35%, Whiteness HP Blue 35%, Whiteness HP Maxx 35%, and Lase Peroxide Sensy 35%. To analyze the degradation of H2O2, the titration of bleaching agents with potassium permanganate was used, while the penetration of H2O2 was measured via spectrophotometric analysis of the acetate buffer solution, collected from the artificial pulp chamber. The analyses were performed immediately as well as 15 minutes, 30 minutes, and 45 minutes after product application. The data of degradation rate of H2O2 were submitted to analysis of variance (ANOVA) and Tukey tests, while ANOVA and Fisher tests were used for the quantification of H2O2, at the 5% level. The results showed that all products significantly reduced the concentration of H2O2 activates at the end of 45 minutes. It was also verified that the penetration of H2O2 was enhanced by increasing the residence time of the product on the tooth surface. It was concluded that the bleaching gels retained substantial concentrations of H2O2 after 45 minutes of application, and penetration of H2O2 in the dental structure is time-dependent.

Enhanced photoelectrocatalytic degradation of an acid dye with boron-doped TiO2 nanotube anodes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fragmentation of lignin from organosolv black liquor by white rot fungi

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Thermal degradation and lifetime estimation of poly(ether imide)/carbon fiber composites

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)