Avaliação da Gravidade Específica e de Outras Medidas Corporais e da Carcaça para Estimar a Composição Corporal de Novilhos Nelore

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of cross-head speed on resin-dentin shear bond strength

Objective: To evaluate the influence of different cross-head speeds on shear bond strength test on the dentin surface.Methods: One hundred and twenty extracted bovine incisors were embedded in polystyrene resin. The specimens were prepared by wet grinding with 320-, 400- and 600-grit Al2O3 paper exposing dentin. After the application of the adhesive system Single Bond (3M) to etched dentin, the composite resin Z-100 (3M) was applied and light cured. The specimens were randomly assigned to four groups (n = 30). The shear bond strength tests were performed with an EMIC DL 500 universal testing machine at four different cross-head speeds: 0.50 (A); 0.75 (B); 1.00 (C); and 5.00 mm/min (D).Results: the mean values of shear bond strength in MPa (SD) were: A, 11.78 (3.91); B, 11.82 (4.78); C, 16.32 (6.45); D, 15.46 (5.94). The data were analyzed with one-way ANOVA and Tukey's test (alpha = 0.05). The results indicated that A = B < C = D. The fracture pattern was evaluated by visual analysis in a stereomicroscope (25 x). The percentage of fractures that occurred at the adhesive interface were: A, 92.5%; B, 91.6%; C, 70.0%; D, 47.0%. The Student's t-test to percentages ( = 0.05) indicated that there were no significant differences among A, B and C; A and B differed from D, and there was no significant difference between C and D.Significance: Different cross-head speeds may influence the shear bond strength and the fracture pattern in dentin substrate. Shear bond strength using cross-head speeds of 0.50 and 0.75 mm/min should be preferred. (C) 2001 Academy of Dental Materials. published by Elsevier B.V. Ltd. All rights reserved.

Avaliação da composição química e física dos cortes da costela para estimar a composição química corporal de novilhos nelore

The objective of this study was to establish equations to estimate the empty body chemical composition of Nellore steers using the following indirect techniques: 1) physical composition of the 9-10-11(th) rib cut;) physical composition of the 10(th) rib cut; and 3) chemical composition of the 10(th) rib cut. Thirty-one Nellore steers with weights ranging from 245 to 489 kg and ages from 20 to 29.7 months at slaughter were utilized. The empty body chemical composition was established through samples collected after grinding all animal tissues. The equations using the percentage of dissectable fat in the 9-10-11(th) rib cut shored a high precision for estimating the percentage of water (r(2) = 0.91; Syx = 1.168) and ether extract (r(2) = 0.94; Syx = 1.298) of the empty body; the same was observed when the percentage of dissectable fat in the 10(th) rib cut was used (r(2) = 0.82 and 0.85; Syx = 1.658 and 1.942, respectively, for water and ether extract). The equations using the percentage of ether extract in the 10(th) rib cut showed a high precision for estimating the percentage of water (r(2) = 0.89; Syx = 1.311) and the ether extract (r(2) = 0.89; Syx = 1.730) of the empty body, but there was no advantage over the physical composition of the 9-10-11(th) and 10(th) rib cut. Multiple regressions using carcass weight and the percentage of bones and kilograms of lean, fat, and bones dissectable in the 10(th) rib cut improved the coefficients of determination for water and ether extract to 0.87 and 0.91. The equations to estimate the percentages of protein and ach showed a low precision, indicating that those techniques are not recommended to estimate these components in the empty body of Nellore steers.

Clinical evaluation of tinnitus in patients with sleep bruxism: prevalence and characteristics

Evaluation of the prevalence and characteristics of tinnitus in a Brazilian series of sleep bruxism patients. In this descriptive study, 100 patients (80 women and 20 men) were selected through the self-report of grinding teeth during sleep, confirmed by room mate or family member. They were evaluated according to a systematized approach: a questionnaire for orofacial pain and the Portuguese version of the Research Diagnostic Criteria for Temporomandibular Disorders. The patients were divided into two groups: group A, 54 patients with complaint of tinnitus and group B, 46 patients without tinnitus complaint. The mean age was 37.85 (13-66 years) and 34.02 years (20-59 years), respectively, for groups A and B (P = 0.1164). There was statistically significant difference between the two groups, with higher prevalence for the group A, in relation to: presence of chronic facial pain (P = 0.0007); number of areas painful to palpation in the masticatory and cervical muscles (P = 0.0032); myofascial pain in the masticatory muscles (P = 0.0003); absence of teeth without prosthetic replacement (P = 0.0145) and indices of depression (P = 0.0234). Structural alterations of the TMJ, like disc displacement and vertical dimension loss did not differ for the two groups. Tinnitus frequency was higher in patients with sleep bruxism and chronic facial pain. Myofascial pain, number of areas painful to palpation in the masticatory and cervical muscles, higher levels of depression and tooth absence without prosthetic replacement were more frequent in the group with tinnitus.

Determination of vanadium in human hair slurries by electrothermal atomic absorption spectrometry

This work describes an analytical procedure for vanadium determination in human hair slurries by electrothermal AAS using longitudinal heating (LHGA) and transversal heating (THGA) graphite furnace atomizers. The samples were powdered using cryogenic grinding and the hair slurries containing 0.2% (m/v) were prepared in three different media for determination of vanadium: 0.14 mol L-1 HNO3, 0.1% (v/v) Triton X-100 and 0.1% (v/v) water soluble tertiary amines (CFA-C, pH 8). The limits of detection (LOD), limits of quantification (LOQ), and characteristic masses obtained were 0.28, 0.95 mu g L-1 and 35 pg (LHGA) and 0.34, 1.13 mu g L-1 and 78 pg (THGA), respectively. The accuracy of the analytical results obtained by the proposed procedure in both equipments was confirmed by a paired t-test at the 95% confidence level and compared with a conventional procedure based on acid digestion. (c) 2006 Elsevier B.V. All rights reserved.

Effect of microwave sterilization and water storage on the Vickers hardness of acrylic resin denture teeth

Statement of problem. Acrylic resin denture teeth soften upon immersion in water, and the heating generated during microwave sterilization may enhance this process.Purpose. Six brands of acrylic resin denture teeth were investigated with respect to the effect of microwave sterilization and water immersion on Vickers hardness (VHN).Material and Methods. The acrylic resin denture teeth (Dentron [D], Vipi Dent Plus [V], Postaris [P], Biolux [B], Trilux [T], and Artiplus [A]) were embedded in heat-polymerized acrylic resin within polyvinylchloride tubes. For each brand, the occlusal surfaces of 32 identical acrylic resin denture posterior teeth were ground flat with 1500-grit silicon carbide paper and polished on a wet polishing wheel with a slurry of tin oxide. Hardness tests were performed after polishing (control group, C) after polishing followed by 2 cycles of microwave sterilization at 650 W for 6 minutes (MwS group), after polishing followed by 90-day immersion in water (90-day Wim group), and after polishing followed by 90-day storage in water and 2 cycles of microwave sterilization (90-day Wim + MwS group). For each specimen, 8 hardness measurements were made and the mean was calculated. Data were analyzed with a 2-way analysis of variance followed by the Bonferroni procedure to determine any significance between pairs of mean values (alpha=.01).Results: Mircrowave sterilization of specimens significantly decreased (P <.001) the hardness of the acrylic resin denture tooth specimens P (17.8 to 16.6 VHN, V (18.3 to 15.8 VHN), T (17.4 to 15.3 VHN), B (16.8 to 15.7 VHN), and A (17.3 to 15.7 VHN). For all acrylic resin denture teeth, no significant differences in hardness were found between the groups Mws, 90-day Wim, and 90-day Wim + MwS, with the exception of the 90-day Wim + MwS tooth A specimens (14.4 VHN), which demonstrated significant lower mean values (P <.001) than the 90-day Wim (15.8 VHN) and MwS (15.7 VHN) specimens.Conclusions. For specimens immersed in water for 90 days, 2 cycles of microwave sterilization had no effect on the hardness of most of the acrylic resin denture teeth.

Dressing monitoring with a digital signal processor

Grinding is a finishing process in machining operations, and the topology of the grinding tool is responsible for producing the desired result on the surface of the machined material The tool topology is modeled in the dressing process and precision is therefore extremely important This study presents a solution in the monitoring of the dressing process, using a digital signal processor (DSP) operating in real time to detect the optimal dressing moment To confirm the monitoring efficiency by DSP, the results were compared with those of a data acquisition system (DAQ) and offline processing The method employed here consisted of analyzing the acoustic emission and electrical power signal by applying the DPO and DPKS parameters The analysis of the results allowed us to conclude that the application of the DPO and DPKS parameters can be substituted by processing of the mean acoustic emission signal, thus reducing the computational effort

Analysis of cement slurries by inductively coupled plasma optical emission spectrometry with axial viewing

The feasibility of Portland cement analysis by introduction of slurries in an inductively coupled plasma optical emission spectrometer (ICP-OES) with axial viewing has been evaluated. After a fast manual grinding of the cement samples, owing to the pulverized state of this material, 0.1% m/v slurries were prepared in 1% v/v HCl. The calibration was performed adopting two strategies: one based on slurries prepared from different masses (50, 75, 100 and 125 mg) of a Portland cement standard reference material (NIST SRM 1881), and the other one based on aqueous reference solutions. A complete analysis of cement for major (Al, Ca, Fe, Mg and Si), minor and trace elements (Mn, P, S, Sr and Ti) was accomplished. Both strategies led to accurate results for commercial Portland cement samples, except for Si and Ti. for which the calibration with aqueous reference solutions resulted in low values. Applying a paired t-test it was shown that most results were in agreement at a 95% confidence level with a conventional fusion decomposition procedure. The ICP-OES with axial viewing and end-on gas configuration for removal of the recombination plasma zone was effective for cement slurry analysis without any undesirable particle deposition in the pre-optics interface and without severe spectral interferences. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Efeito alelopático de extrato aquoso de folhas de Azadirachta indica A. Juss. em alface, soja, milho, feijão e picão-preto

The family Meliaceae has been identified as one of the most promising for biological control, as most species have biologically active compounds. Among the species, the Neem (Azadirachta indica A. Juss) is that stands out most for its efficiency and low toxicity, and it is utilized to control insects, fungi and nematodes. The aim of this work was to verify the allelopathic potential of aqueous extract of fresh leaves of Neem on germination of lettuce, soybeans, maize, beans and Bidens pilosa, as a way to control this weed. The extract was obtained by grinding 200g/L of fresh leaves of the Neem (considered extract 100%) and diluting in distilled water at concentrations of 80, 60, 40, and 20%, and a control with only water. The seeds were kept in the germination chamber at a temperature of 25 degrees C, with photoperiod of 12 hours of light. The aqueous extract affected the germination percentage and average length root of lettuce, with values of 1% and 0.1, cm respectively. For the soybeans, the extract influenced negatively the average time of germination and average speed of germination. There was a drastic reduction of the average root length at higher concentration for soybean, corn and beans. For Bidens pilosa all the parameters analyzed were negatively affected, which means sensitivity to the extract. The bioassay performed in the laboratory showed that the aqueous extract of fresh leaves of Azadirachta indica has allelopathic effect on all species.

Performance of low/correct pressure radial ply tires

Extensive field testes were conducted using the UCD single wheel tester employing three large radial ply tractor tires in two different soils, four different soil conditions, two axle load levels, and three levels of tire inflation pressures in order to quantify the benefits of using low/correct inflation pressures. During these tests slip, net traction, gross traction, and dynamic axle load were recorded. Furthermore, soil moisture content, cone index, and dry bulk density data were obtained at test locations. The results of the analysis showed a significant increase in net traction and traction efficiency when low/correct inflation was used. Benefits of using low/correct pressure was higher in tilled soil conditions.

Microtensile bond strength between a quartz fiber post and a resin cement: Effect of post surface conditioning

Purpose: To test the bond strength between a quartz-fiber-reinforced composite post (FRC) and a resin cement. The null hypothesis was that the bond strength can be increased by using a chairside tribochemical silica-coating system. Materials and Methods: Thirty quartz-FRCs (Light-Post) were divided into 3 groups according to the post surface treatment: G1) Conditioning with 32% phosphoric acid (1 min), applying a silane coupling agent; G2) etching with 10% hydrofluoric acid (1 min), silane application; G3) chairside tribochemical silica coating method (CoJet System): air abrasion with 30-μ SiO x-modified Al2O3 particles, silane application. Thereafter, the posts were cemented into a cylinder (5 mm diameter, 15 mm height) with a resin cement (Duo-Link). After cementation, the specimens were stored in distilled water (37°C/24 h) and sectioned along the x and y axes with a diamond wheel under cooling (Lab-cut 1010) to create nontrimmed bar specimens. Each specimen was attached with cyanoacrylate to an apparatus adapted for the microtensile test. Microtensile testing was conducted on a universal testing machine (1 mm/min). The data obtained were submitted to the one-way ANOVA and Tukey test (α = 0.05). Results: A significant influence of the conditioning methods was observed (p < 0.0001). The bond strength of G3 (15.14 ± 3.3) was significantly higher than the bond strengths of G1 (6.9 ± 2.3) and G2 (12.60 ± 2.8) (p = 0.000106 and p = 0.002631, respectively). Notwithstanding the groups, all the tested specimens showed adhesive failure between the resin cement and FRC. Conclusion: The chairside tribochemical system yielded the highest bond strength between resin cement and quartz-fiber post. The null hypothesis was accepted (p < 0.0001).

Automatic system for thermal damage detection in manufacturing process with Internet monitoring

This work involved the development of a smart system dedicated to surface burning detection in the grinding process through constant monitoring of the process by acoustic emission and electrical power signals. A program in Visual Basic® for Windows® was developed, which collects the signals through an analog-digital converter and further processes them using burning detection algorithms already known. Three other parameters are proposed here and a comparative study carried out. When burning occurs, the newly developed software program sends a control signal warning the operator or interrupting the process, and delivers process information via the Internet. Parallel to this, the user can also interfere in the process via Internet, changing parameters and/or monitoring the grinding process. The findings of a comparative study of the various parameters are also discussed here. Copyright © 2006 by ABCM.

Influence of the tool edge geometry on specific cutting energy at high-speed cutting

This paper presents specific cutting energy measurements as a function of the cutting speed and tool cutting edge geometry. The experimental work was carried out on a vertical CNC machining center with 7,500 rpm spindle rotation and 7.5 kW power. Hardened steels ASTM H13 (50 HRC) were machined at conventional cutting speed and high-speed cutting (HSC). TiN coated carbides with seven different geometries of chip breaker were applied on dry tests. A special milling tool holder with only one cutting edge was developed and the machining forces needed to calculate the specific cutting energy were recorded using a piezoelectric 4-component dynamometer. Workpiece roughness and chip formation process were also evaluated. The results showed that the specific cutting energy decreased 15.5% when cutting speed was increased up to 700%. An increase of 1 °in tool chip breaker chamfer angle lead to a reduction in the specific cutting energy about 13.7% and 28.6% when machining at HSC and conventional cutting speed respectively. Furthermore the workpiece roughness values evaluated in all test conditions were very low, closer to those of typical grinding operations (∼0.20 μm). Probable adiabatic shear occurred on chip segmentation at HSC Copyright © 2007 by ABCM.

Presence of extraintestinal pathogenic Escherichia coli in butcheries in Taquaritinga, SP, Brazil

The study was conducted in twenty-three butcheries in the city of Taquaritinga, State of São Paulo, Brazil, surveyed during a 10 months period. Among two hundred and eighty-seven Escherichia coli strains isolated from samples of ground beef, meat-grinding-machines and the hands of manipulators, five were recognized as extraintestinal pathogenic E. coli (ExPEC), showing virulence factors (P and S fimbriae, hemolysin and aerobactin) and presenting multidrug resistance. Retail-sold food may constitute an important vehicle for the dissemination of ExPEC in communities, giving rise to reasons for concern.

Compactação do solo e intervalo hídrico ótimo no crescimento da parte aérea e produtividade da cultura do milho

The aim of this work was to evaluate the effect of soil compaction caused by tractor wheel traffic on the limiting water range (LLWR), shoot growth and levels of compaction and four replications in a completely randomized experimental design. Soil samples with preserved structure were collected in the layers: 0.02-0.05; 0.08-0.11; 0.15-0.18 and 0.22-0.25m to determine macroporosity, microporosity, total porosity, bulk density, resistance to penetration and LLWR. The evaluated corn parameters were: plant and first spike height, steam diameter, number of spikes per plant, plant dry matter, dry matter of 1000 seeds and seed productivity. The soil compaction restricted all corn parameters except the number of spikes per plant and dry matter of 1000 seeds. The LLWR was reduced by the soil resistance to penetration, even in the tilled soil with bulk density of 1.12 Mg m-3. Only the treatment with 11 Mg tractor, repeated four times on the area, demonstrated bulk density above critical bulk density in the LLWR that was 1.37 Mg m-3, where the seed productivity was significantly smaller.