Preparation of Fe-Cr-P-Co amorphous alloys by electrodeposition

The effects of bath composition and electroplating conditions on structure, morphology, and composition of amorphous Fe-Cr-P-Co deposits on AISI 1020 steel substrate, priorly plated with a thin Cu deposit, were investigated. The increase of charge density activates the inclusion of Cr in the deposit. However, above specific values of the charge density, which depend on the deposition current density, the Cr content in the deposit decreases. This Cr content decreasing is probably due to the significant hydrogen evolution with the increasing of deposition cur-rent and charge density. The effect of charge density on the content of Fe and Co is not clear. However, there is a tendency of increasing of Fe content and decreasing of Co content with the raising of current density. The Co is more easily deposited than the P, and its presence results in a more intense inhibition effect on the Cr deposition than the inhibition effect caused by P presence. Scanning electron microscope (SEM) analysis showed that Co increasing in the Fe-Cr-P-Co alloys analyzed does not promote the susceptibility to microcracks, which led to a good quality deposit. The passive film of the Fe-Cr-P-Co alloy shows a high ability formation and high protective capacity, and the results obtained by current density of corrosion, j(cor), show that the deposit with addition of Co, Fe31Cr11P28Co30, presents a higher corrosion resistance than the deposit with addition of Ni, Fe54Cr21P20Ni5. (C) 2004 Published by Elsevier B.V.

Differences in the number of sensilla coeloconica and sensilla ampullacea of segment 10 of the antennae of Africanized and Caucasian bees and of their F1 hybrids

The numbers of sensilla coeloconica and sensilla ampullacea of segment 10 of the antennae of Caucasian and Africanized worker bees and of their hybrids were counted with the aid of a scanning electron microscope. Africanized bees have fewer sensilla than Caucasian bees and the continuous distribution obtained from the F1 values suggests polygenic inheritance for the control of this trait. There are also indications that the hybrid Brazilian Apis mellifera studied here are close to typical African bees (Apis mellifera scutellata) in terms of number of sensilla.

Microleakage evaluation of pit and fissure sealants done with different procedures, materials, and laser after invasive technique

This study evaluated the microleakage of pit and fissure sealants after different surface preparation (invasive technique and laser irradiation) and the use of different materials (fluoride resin-filled sealant, resin-modified glass ionomer cement and adhesive system). Eighty-four pre molars were used in this study, which were divided into seven groups. After the accomplishment of the different treatments, these were submitted to thermocycling process and assess for microleakage by examination under an epifluorescent microscope and scored zero to seven. Two specimens of each group were observed under scanning electron microscope (SEM). The results showed that laser irradiation did not lessen microleakage in pit and fissures when using a filled-resin sealant with fluoride or a resin-modified glass ionomer cement. The use of laser irradiation and adhesive system, followed by a resin-filled sealant with fluoride, showed the lowest microleakage scores in pit and fissures. Comparing this group to the resin-modified glass ionomer cement group, there was statistical significance. The use of a adhesive system decreased microleakage when using a fluoride resin-filled sealant with or without previous laser irradiation; although it was not statistically significant.

Desarrollo ontogénico de plántulas de Guazuma ulmifolia (Sterculiaceae)

Guazuma ulmifolia is as popular reforestation tree all over Latin America. It is characteristic of the initial stages of the secondary sucession and presents potential utility in the restoring of degraded areas. There is no information about fruit, seed and seedling morphology, which is of fundamental importance for identification, extraction, management and seed germination as well as for the characterization of post-seminal development and normal seedling pattern. To obtain such information, external fruit, and external and internal seed structures were studied considenng shape, size, micropile and embryo localization, and tegumentar structures. All stages of this work were conduced in the Universidade Estadual Paulista (UNESP), Campus of Jaboticabal city. The fruits were collected in a mixed plantation in Jaboticabal city, State of São Paulo, Brazil. For the biometric study eight repetitions of ten fruits and eight repetitions of 100 seeds were utilized. For seed internal traits study, 50 seeds were drenched in a distiled water, cut, and observed with a scanning electron microscope and a stereomicroscope. For post-seminal study ten repetitions of seven seeds were scarificated chemically with sulphuric acid during 50 min, and placed to germinate in a culture medium, at 30°C, and eight hours of photoperiod. We found elipsoid, woody, indehiscent, pentacarpelar fruits, with a mean lenght of 22.61 mm (diameter 24.88 mm) and 64.0 seeds per fruit. Seed shape varies, mean length is 3.07 mm (width of 2.36 mm).The seed is bitegumented, tegmic, with a continuous, axial and curved embryo. The germination is epigeal and the seedlings are fanerocotiledoneus. Drawings of all stages are included.

Submicroscopical features of leaves of xyris species

The leaf infrastructure of five Xyris species were examined using scanning electron microscope (SEM), transmission electron microscope (TEM) and histochemical methods. All studied leaves show some features in epidermis and mesophyll, which were of considerable adaptative significance to drought stress. Such features included the occurrence of a pectic layer on the stomatal guard cells and the presence of a nehvork ofpectic compounds in the cuticle. Pectic compunds were also in abundance in lamellated walls of the mesophyll cells and on the inner surface of the sclerified cell walls of the vascular bundle sheaths. There were also specialized chlorenchymatous peg cells in the mesophyll and drops of phenolic compounds inside the epidermal cells.

EM evaluation of bacterial biofilm and microorganisms on the apical external root surface of human teeth

The aim of this study was to evaluate the presence of bacterial biofilm on the external surface of the root apex in teeth with pulp necrosis, with and without radiographically visible periapical lesions, and in teeth with a vital pulp. Twenty-one teeth were extracted, eight with pulp necrosis and periapical lesions, eight with pulp necrosis without radiographically visible periapical lesions, and five with a vital pulp. The roots were sectioned, and the root apexes (+/- 3 mm) were processed for scanning electron microscope evaluation. The surface of the apical root was evaluated for the presence of microorganisms, root resorption, and biofilm. There were no microorganisms on the apical root surface of either teeth with pulp vitality or with pulp necrosis with no radiographically visible periapical lesions. Microorganisms were always present in teeth with pulp necrosis and radiographically visible periapical lesions. These included cocci, bacilli, and filaments and the presence of an apical biofilm. Apical biofilm is clinically important because microbial biofilms are inherently resistant to antimicrobial agents and cannot be removed by biomechanical preparation alone. This may cause failure of endodontic treatment as a consequence of persistent infection.

Effect of air-powder system on titanium surface on fibroblast adhesion and morphology.

PURPOSE: To evaluate the number and morphology of fibroblasts grown on machined titanium healing abutments treated with an airpowder system. MATERIALS AND METHODS: Twenty-six abutments were assigned to two experimental groups: control (no treatment) and treated (exposed to the Prophy-Jet for 30 seconds). The specimens were incubated for 24 hours with fibroblastic cells in multiwell plates, followed by routine laboratory processing for scanning electron microscope analysis. The specimens were photographed at x 350, and the cell number was counted on an area of approximately 200 um2. RESULTS: No significant differences were found on morphology between the groups (P > 0.05); however, the control group presented a significantly greater amount of cells (71.44 +/- 31.93, mean +/- SD) in comparison with treated group (35.31 +/- 28.14), as indicated by a nonpaired t test (P = 0.001). CONCLUSION: The use of an air-abrasive prophylaxis system on the surface of titanium healing abutments reduced the cells proliferation but did not influence cell morphology.

Is the number of antennal plate organs (sensilla placodea) greater in hygienic than in non-hygienic Africanized honey bees?

Hygienic behavior is a desirable trait in honey bees (Apis mellifera L.), as hygienic bees quickly remove diseased brood, intermpting the infectious cycle. Hygienic lines of honey bees appear to be more sensitive to the odors of dead and diseased honey bee brood, and Africanized honey bees are generally more hygienic than are European honey bees. We compared the number of sensilla placodea, antennal sensory structures involved in the perception of odor, in 10 bees from each of six hygienic and four non-hygienic colonies of Africanized honey bees. The sensilla placodea of three of the terminal segments (flagellomeres) of the right antenna of each bee were counted with a scanning electron microscope. There were no significant differences in the mean numbers of sensilla placodea between the hygienic and non-hygienic bees, though the variance was higher in the hygienic group. Flagellomere 4 had significantly more sensilla placodea than flagellomeres 6 and 8. However, there was no significant difference between the other two flagellomeres. As hygienic bees are capable of identifying dead, injured, or infested brood inside a capped brood cell, sensilla placodea probably have an important role in enabling worker bees to sense sick brood. However, we did not find greater numbers of this sensory structure in the antennae of hygienic, compared to non-hygienic Africanized honey bees.

The effect of CO 2 laser irradiation on failed implant surfaces

The aim of this investigation was to evaluate the cleaning effect of CO 2 on surface topography and composition of failed dental implant surfaces. Ten failed dental implants were retrieved from nine patients (mean age, 46.33 ± 5.81 years) as a result of early or late failure. The implants were divided into two parts: one side of the implant was irradiated with a CO 2 laser (test side), while the other side did not receive irradiation (control side). The CO 2 laser was operated at 1.2 W in a continuous wave for 40 seconds (40 J energy). The handpiece of the CO 2 laser was kept at a distance of 30 mm from the implant surface, resulting in a spot area of 0.031415 cm 2 (38.20 W/cm 2; 1559 J/cm 2) in scanning mode (cervical-apical). One unused dental implant was used as a negative control for both groups. All implant surfaces were examined by scanning electron mi croscopy (SEM) and energy-dispersive spectrometer x-ray (EDS) for element analysis. SEM showed that the surface of the test sides consisted of different degrees of organic residues, appearing mainly as dark stains similar to those observed on the control sides. None of the test surfaces presented alterations such as crater-like alterations, lava-like layers, or melting compared with the nonirradiated surfaces. Foreign elements such as carbon, oxygen, sodium, calcium, and aluminum were detected on both sides. These results suggest that CO 2 laser irradiation does not modify the implant surface, although the cleaning effect was not satisfactory.

Avaliação da formação do biofilme de Candida albicans sobre superfície de titânio revestida com hidroxiapatita por meio de microscopia eletrônica de varredura

In this study Candida albicans biofilm formation on the surface of commercially pure titanium (cp-Ti) coated with hydroxyapatite was observed by means of scanning electron microscope. The biofilm was formed after 45 days of incubation of the samples in liquid culture medium inoculated with fungus cells in a tube of polystyrene with screw cap and sterilized. After the biofilm removal with 10% EDTA solution was observed pitting on the surface of cp-Ti coated.

Aderência e formação do biofilme por Staphylococcus aureus ao polietilenotereftalato (PET) usado como embalagem para acondionamento de medicamentos e cosméticos

The polyethylene terephthalate (PET) is used for package drugs and cosmetics. The aim of this research was examine by scanning electron microscopy (SEM) a Staphylococcus aureus attachment and biofilm formation on a polyethylene terephthalate (PET) surface and hydrophobicity of S. aureus by adherence to hydrocarbons. A suspension of S. aureus was prepared in Mueller-Hinton broth and, coupons of polyethylene terephthalate were incubated for 30 minutes, two, 24 and 48 hours, 15 and 30 days. Afteron the coupons were removed and prepared for scanning electron microscope analysis. The attachment and biofilm formation was observed on the surfaces of PET. The SEM revealed adhesion and biofilm formation on PET surfaces. The hydrophobicity test classified S. aureus as hydrophobic.

Effects of electroplated zinc-nickel alloy coatings on the fatigue strength of AISI 4340 high strength steel

It is well known that fatigue behaviour is an important parameter to be considered in mechanical components subjected to constant and variable amplitude loadings. In combination with corrosion phenomenon, fatigue effects were responsible for proximally 64% of fails that occur in metallic parts of aeronautical accidents in the last 30 years. Recovered substrates have been extensively used in the aerospace field. Cadmium electroplating has been widely applied to promote protective coatings in aeronautical components, resulting in excellent corrosion protection combined with a good performance in cyclic loading. Ecological considerations allied to the increasing demands for corrosion resistance, resulted in the search for possible alternatives. Zinc-nickel alloys received considerable interest recently, since these coatings showed some advantages such as a good resistance to white and red rust, high plating rates and acceptation in the market. In this study the effects of zinc-nickel coatings electroplated on AISI 4340 high strength steel were analysed on rotating bending and axial fatigue strength, corrosion and adhesion resistance. Compressive residual stress field was measured by a X-ray tensometry prior to fatigue tests. Optical microscopy images showed coating thicknesses, adhesion and the existence of an uniform coverage of nearly all substrates. The fractured fatigue specimens were investigated using a scanning electron microscope. Three different zinc-nickel coating thicknesses were tested and comparison with rotating bending fatigue data from specimens cadmium electroplated and heat treated at 190°C for 3, 8 and 24 hours to avoid the diffusion of hydrogen in the substrate, was performed. Experimental results showed effect of coatings on the AISI 4340 steel behaviour when submitted to fatigue testing and the existence of coating thickness influence on the fatigue strength.

Características ultraestruturais do segmento abdominal da aorta de rato albino

The objective of the present research was to investigate the ultrastructural peculiarities of the aortic wall of the rat. Seven young adult rats were used, from which fragments of the infrarenal abdominal aorta were collected. After collection, the vascular segments were fixed and sent for analysis by scanning electron microscope. The elastic lamellae appear interposed with smooth muscular fibers; this pattern was verified mainly at the medial layer structure. Among the mural elements a well defined interrelationship was established through connective lamellae of the arterial wall. The collagen lamellae mainly provided anchoring among the elastic and smooth muscular constituents. The intimal layer showed special ultrastructural features, such as a non-continuous inner elastic lamina presented in certain sites of the vascular wall, followed by endothelial pores. This mural pattern of the abdominal aorta provided support to vascular functions such as shrinkage among the laminar composition of the arterial layers, also acting in mechanical properties of the vascular wall, such as viscoelasticity and contractility - essential actions to blood vessel hemodynamics.

SEM analysis of the in situ early bacterial colonization on two novel feldspathic ceramics submitted to different types of glazing

Aim: The aim of this study was to evaluate in situ, the early bacterial colonization on feldspar-ceramics submitted to different glazing. Methods and Materials: Fourteen standardized disc specimens (diameter: 5 mm, thickness: 1.5 mm) of each of two micro-particulate feldspathic ceramics (VM7 and VM13, Vita) were produced according to manufacturers' specifications for a total of 28 specimens (24 for the analysis of biofilm and 4 for topographic analysis analyzing the ceramic surfaces). Specimens from each type of ceramic were submitted to two different glazing methods composing four groups: VM7 glazed using glazing liquid Vita Akzent® 25 (G1) and glaze firing (G2), VM13 glazed using glazing liquid (G3) and glaze firing (G4). Six individuals (n=6) wore oral appliances with four ceramic specimens, fixed on the buccal face of the appliances. After 8 hours, each sample was evaluated for the presence (1) or absence (0) of bacterial colonization under a scanning electron microscope (SEM) on five randomly selected fields. The value for each sample was cumulative of the results observed in the fields. One sample from each group was evaluated under a SEM to verify the topographic pattern. Results: There was no difference with regard to bacterial colonization between the feldspar-ceramics and between the glazing types (Kruskal-Wallis non-parametric test). Conclusion: Feldspar-ceramics submitted to firing or glaze firing with Vita Akzent® 25 present a similar condition for in situ bacterial colonization. The similar topographic pattern of the ceramic surfaces seems to have influenced the bacterial colonization.

Microscopic, morphometric and ultrastructural analysis of anastomotic healing in the intestine of normal and diabetic rats

The purpose of this study was to investigate if experimental alloxanic diabetes could cause qualitative changes in intestinal anastomoses of the terminal ileum and distal colon in rats, as compared to controls. 192 male Wistar rats, weighing ± 300g were split into four experimental groups of 48 animals each, after 3 months of follow-up: a control group with ileum anastomoses (G1), a control group with colon anastomoses (G2), a diabetic group with ileum anastomoses (G3) and a diabetic group with colon anastomoses (G4). Animals were evaluated and sacrificed on days 4, 14, 21 and 30 after surgery, and fragments of the small and large intestine where the anastomoses were performed were removed. Samples from 6 animals from each sacrifice moment were submitted to ultrastructural analysis of the collagen fibers using a scanning electron microscope and samples from another 6 animals were submitted to histopathology and optical microscopy studies using picrosirius red-staining. Histopathological analysis of picrosirius red-stained anastomosis slides using an optical microscope at 40x magnification showed that the distribution of collagen fibers was disarranged and also revealed a delay in scar tissue retraction. The morphometric study revealed differences in the collagen filled area for the ileum anastomoses 14 days post surgery whereas, in the case of colon anastomoses, differences were observed at days 4 and 30 post surgery, with higher values in the diabetic animals. Ultrastructure analysis of the ileum and colon anastomoses using a scanning electron microscope revealed fewer wide collagen fibers, the presence of narrower fibers and a disarranged distribution of the collagen fibers. We conclude that diabetes caused qualitative changes in scar tissue as well as in the structural arrangement of collagen fibers, what could explain the reduced wound strength in the anastomosis of diabetic animals. © J. A. Barth Verlag in Georg Thieme Verlag KG Stuttgart.