Desenvolvimento de um sistema para caracterização de dispositivos eletroluminescentes

The materials designed to be used in electroluminescent (EL) devices construction are studied and improved since 1936. Great interests in the development of this kind of devices are mainly due to its low power consumption, flexibility, low cost and easy processing. One class of ELs devices with these characteristics are produced by employing a organic-polymeric/inorganic composite from a conductive polymer blend and an inorganic electroluminescent material (Zn2SiO4:Mn) dispersed in the polymeric matrix. This kind of device operates in d.c. or a.c. potentials, with EL of hundreds candela in the green region of the visible spectrum. However, few studies on the light emission were performed for these devices. In order to characterize devices made from composites, in this work is proposed a method of characterizing the electroluminescence associated with the impedance spectroscopy technique. To implement the technique of impedance spectroscopy was employ an experimental setup consisting of a source of a.c. voltage, an oscilloscope, and a reference resistor. Associated with this system, was use a photo diode and an analog electrometer to characterize the emitted light signal from the sample. The system was implemented allows characterization by impedance spectroscopy in the frequency range from 0.2 Hz up to 2 MHz and voltage amplitudes of 5 mV up to 20 kV. This system permits, at the same time, measurement of the RMS value of the luminance for devices in frequency range from 20 Hz up to 2 MHz. To test the system efficiency, an EL device was characterized showing analogous results to those reported in literature. By doing this, was demonstrated the efficiency of the system for electroluminescence characterization associated with the electrical characterization by impedance spectroscopy, for devices

Sistema fotovoltaico interligado á rede eletrica no Campus da UNESP-FEG Guaratinguetá

Solar energy can be considered the largest source of energy available on earth and has attracted in recent decades, attention and interest for its rational use. The use of energy sources in a sustainable manner is essential to the survival of future generations, due to the scarcity of natural resources and their exploitation in a disorderly way. Studies related to the applications of renewable sources becomes then relevant, given its great importance as regards the conscious use of resources provided by nature, with the least possible impact on it. The present study presents an evaluation of generation potential and feasibility of implementing a solar photovoltaic connected to the grid and connected to the roofs of some buildings of the Faculty of Engineering of Guaratinguetá - FEG, to supply the demand of electric energy consumption on campus and attempting to inject a possible surplus power generation in local power grid, increasing network capacity and reducing peak loads

Avaliação de sistemas de pultrudados com diferentes tipos de matrizes para aplicação em cabos condutores

In the last decades it has been observed a substantial developing of the electrical energy demand in the societies all over the World. In consequence the electrical energy distribution companies are increasing the quantity of electrical energy through the electrical energy conductor cables, which had grown the sag in the towers of energy transmission. Furthermore, the construction of more transmission towers brings a lot of troubles due environmental protection laws. In this way, looking forward to increase the quantity of electrical energy transmitted through electrical cables conductors, reduce the need of constructing new transmission towers and the sag in them, we suggest in this work the replace of the traditional core of the conductors cables commonly used, made of steel, by a core made by a composite material, which one is made by carbon fibers pultruded with polymeric resins as matrix. In a order to evaluate if the resins more commonly used in structural composites can be applied as matrix to make possible to use the composite material as a core, we made carbon fibers systems pultruded with epoxy, phenolic and polyester resins as matrix and a mechanic and physic-chemistry characterization was done on the systems by Tensile and Poisson tests, differential sprobe calorimetry (DSC), thermogravimetric analysis (TGA) and Fourier transformed infrared spectroscopy (FTIR), following their correspondents standards

Viabilidade técnica e econômica na utilização de um sistema fotovoltaico para alimentação de luminárias LED na Faculdade de Engenharia do Campus de Guaratinguetá SP

Solar energy can be considered the largest source of energy available on earth and has attracted in recent decades, attention and interest for its rational use. The use of energy sources in a sustainable way is essential to the survival of future generations, due to the scarcity of natural resources and their exploitation in a disorderly way. This academic work aims to bring a possible alternative to reduce the consumption of eletrical energy, at the University of Engineering – Campus of Guaratinguetá, through the use of a photovoltaic system interconnected to the LED bulbs. For this, the necessary data for the design of the photovoltaic system componentes and their acquisition costs were obtained and three differents configurations were developed to choose the one that bests fits the studied case, considering the return time of the initial investment (payback)

Avaliação do efeito da paralisação da aeração no tratamento biológico aeróbio da água residuária da indústria de farinha de mandioca

The cassava wastewater, generated during the cassava processing, is a pollutant and toxic waste. This study compared the efficiency of the cassava wastewater treatment in three batch aerobic systems with a ru1nning time of 24 hours, and aeration stoppage of 12h with 2,500, 6,000 and 10,000 mg COD L-1 . The systems were evaluated for COD, pH, SVI and F/M. The results showed that the reactor with aeration stoppage for 12 hours, with 2,500 mg COD L-1 , presented the best reduction in a process with considerable energy consumption saving compared to traditional continuous systems.

Estudo sobre eficiência energética em uma indústria de injeção plástica

The reason of this work is perform a study about using of electrical energy to identify the opportunities through rational use of electrical energy. For that it was necessary perform an analysis of hired energy against consumption. Based in a guide of energy analysis were found the main consumers and verified the main problems, which generate excessive use of electrical energy in a plastic injection factory. It was also analyzed the painting line because there are some thermal equipment that use electrical energy. Based on the data obtained will be proposed ways to reduce the needless consumption and energy use of rationally and efficiently, in addition to re-evaluate the contracted demand based on the new policy of supplying and charging.It were also proposed thermodynamics solutions to reduce the energy consumed in thermal process

Estudo de impacto de ações de eficiência energética em instalações elétricas residenciais

This paper addresses methods of reducing the electric energy consumption on residences by the means of constructive measures and replacement of electric devices. Analyzing their impacts on residential and national level based on data issued by IBGE (Brazilian Institute of Geography and Statistics) and PROCEL (National Program for Electricity Conservation).

Sistema de automação residencial controlado via rede doméstica

The present work develops a residential automation system controlled by PIC microcontroller connected to a domestic network using the TCP/IP protocol. This was motivated by the viability of building an automation system to control basic elements of a house with low cost, which cannot be found nowadays. Initially is presented a brief history of the automation systems and an introduction about PIC microcontrollers. Afterwards is presented an overview of the system to be implemented. Then it is shown a suggested circuit and the sensor and actuator elements as well as the software to manage the system, this was all build and test in the laboratory. In the end are the results obtained from the prototype, like the energy consumption, the cost, efficiency and reliability

Obtenção de rochas sintéticas a partir de resíduos de vidro comercial e pó de granito

Pós-graduação em Engenharia Mecânica - FEG

Análise energética da aplicação de torta de filtro na substituição parcial da adubação inorgânica sintética da cana-de-açúcar

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Predição da emissão de metano entérico de bovinos Nelore

Pós-graduação em Zootecnia - FCAV

Avaliação de sistema de climatização em Poedeiras comerciais

Pós-graduação em Ciência e Tecnologia Animal - FEIS

Desenvolvimento, implantação e avaliação do desempenho de biorreator anaeróbico de leito fluidizado e leito fixo com filtros biológicos em materiais diversos

This study aimed to develop, implement and evaluate the performance of a new type of bioreactor for anaerobic treatment of wastewater using different filling materials like trickling filters post-reactor. This bioreactor has mixed characteristics of the UASB reactors and horizontal flow from the point of view of removal of BOD (Biochemical Oxygen Demand) ssed (settled solids), TS (Total Solids), SS (Suspended Solid), SD (Dissolved Solids) and turbidity. The experimental model consists of a bioreactor with a volume of 12 m³, 2/3 filled by fluidized bed and 1/3 for fixed. The fluidized bed is made of polystyrene plates used as a system percolation and compartmentalized trickling filters, where each compartment was filled with a support medium with different characteristics (gravel number 4, plastic rings of polystyrene, PET and HDPE) . In addition, the output of a filter system was installed three entries filled with activated carbon. The bioreactor was installed in private residence in the city of Igarapava-SP (20° 02'40.18"S and 47° 45'01.36" W). The system was highly efficient as the removal of organic contaminant load 92% on average reducing the BOD, a significant result when compared to other anaerobic systems. For the other parameters, the mean reduction was 96% for turbidity, 99% ssed, 67.5% ST, 57% SD and 88% of SS. As for its operation the system was capable of operating in continuous flow without the need for maintenance during the entire period of evaluation and without energy, as it operates taking advantage of the natural slope of the terrain where it is installed. The environmental impacts were minimized due to the preservation of local vegetation allowing the ecosystem to remain unchanged beyond the prototype was completely sealed preventing exhalation of odors and therefore not causing inconvenience to neighboring populations. Given these facts it was concluded that the prototype is shown to be highly feasible deployed as a new alternative for treatment of sewage in rural and urban settings (individual homes, condos, farms, ranches, etc.) Due to ease of design and operability, and sustainability at all stages of execution.

Otimização da operação de sistemas de distribuição radiais usando um algoritmo genético especializado

Pós-graduação em Engenharia Elétrica - FEIS

Alterações na expressão do Hormônio Concentrador de Melanina (MCH) na área hipotalâmica lateral do rato ao longo do desenvolvimento pós-natal e envelhecimento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)