Study of alternative schemes for the parameterization step of the continuation power flow method based on physical parameters, part I: Mathematical modeling

The conventional power flow method is considered to be inadequate to obtain the maximum loading point because of the singularity of Jacobian matrix. Continuation methods are efficient tools for solving this kind of problem since different parameterization schemes can be used to avoid such ill-conditioning problems. This paper presents the details of new schemes for the parameterization step of the continuation power flow method. The new parameterization options are based on physical parameters, namely, the total power losses (real and reactive), the power at the slack bus (real or reactive), the reactive power at generation buses, and transmission line power losses (real and reactive). The simulation results obtained with the new approach for the IEEE test systems (14, 30, 57, and 118 buses) are presented and discussed in the companion paper. The results show that the characteristics of the conventional method are not only preserved but also improved.

Study of alternative schemes for the parameterization step of the continuation power flow method based on physical parameters, part II: Performance evaluation

New parameterization schemes have been proposed by the authors in Part I of this paper. In this part these new options for the parameterization of power flow equations are tested, namely, the total power losses (real and reactive), the power at the slack bus (real or reactive), the reactive power at generation buses, and the transmission line power losses (real and reactive). These different parameterization schemes can be used to obtain the maximum loading point without ill-conditioning problems, once the singularity of Jacobian matrix is avoided. The results obtained with the new approach for the IEEE test systems (14, 30, 57, and 118 buses) show that the characteristics of the conventional method are not only preserved but also improved. In addition, it is shown that the proposed method and the conventional one can be switched during the tracing of PV curves to determine, with few iterations, all points of the PV curve. Several tests were also carried out to compare the performance of the proposed parameterization schemes for the continuation power flow method with the use of both the secant and tangent predictors.

Genetic parameters for milk yield, age at first calving and interval between first and second calving in milk buffaloes

Genetic parameters for the relation between the traits of milk yield (MY), age at first calving (AFC) and interval between first and second calving (IBFSC) were estimated in milk buffaloes of the Murrah breed. In the study, data of 1578 buffaloes at first lactation, with calvings from 1974 to 2006 were analyzed. The MTDFREML system was used in the analyses with models for the MY, IBFSC traits which included the fixed effects of herd-year-season of calving, linear and quadratic terms of calving age as covariate and the random animal effects and error. The model for AFC consisted of the herd-year-season fixed effects of calving and the random effects of animal and error. Heritability estimates MY, AFC and IBFSC traits were 0.20, 0.07 and 0.14, respectively. Genetic and phenotypic correlations between the traits were: MY and AFC = -0.12 and -0.15, MY and IBFSC = 0.07 and 0.30, AFC and IBFSC = 0.35 and 0.37, respectively. Genetic correlation between MY and AFC traits showed desirable negative association, suggesting that the daughters of the bulls with high breeding value for MY could be physiological maturity to a precocious age. Genetic correlation between MY and IBFSC showed that the selection of the animals that increased milk yield is also those that tend to intervals of bigger calving.

AATS for the (X)over-bar chart with variable parameters

A Fortran computer program is given for the computation of the adjusted average time to signal, or AATS, for adaptive (X) over bar charts with one, two, or all three design parameters variable: the sample size, n, the sampling interval, h, and the factor k used in determining the width of the action limits. The program calculates the threshold limit to switch the adaptive design parameters and also provides the in-control average time to signal, or ATS.

The STATFLUX code: a statistical method for calculation of flow and set of parameters, based on the Multiple-Compartment Biokinetical Model

The code STATFLUX, implementing a new and simple statistical procedure for the calculation of transfer coefficients in radionuclide transport to animals and plants, is proposed. The method is based on the general multiple-compartment model, which uses a system of linear equations involving geometrical volume considerations. Flow parameters were estimated by employing two different least-squares procedures: Derivative and Gauss-Marquardt methods, with the available experimental data of radionuclide concentrations as the input functions of time. The solution of the inverse problem, which relates a given set of flow parameter with the time evolution of concentration functions, is achieved via a Monte Carlo Simulation procedure.Program summaryTitle of program: STATFLUXCatalogue identifier: ADYS_v1_0Program summary URL: http://cpc.cs.qub.ac.uk/summaries/ADYS_v1_0Program obtainable from: CPC Program Library, Queen's University of Belfast, N. IrelandLicensing provisions: noneComputer for which the program is designed and others on which it has been tested: Micro-computer with Intel Pentium III, 3.0 GHzInstallation: Laboratory of Linear Accelerator, Department of Experimental Physics, University of São Paulo, BrazilOperating system: Windows 2000 and Windows XPProgramming language used: Fortran-77 as implemented in Microsoft Fortran 4.0. NOTE: Microsoft Fortran includes non-standard features which are used in this program. Standard Fortran compilers such as, g77, f77, ifort and NAG95, are not able to compile the code and therefore it has not been possible for the CPC Program Library to test the program.Memory, required to execute with typical data: 8 Mbytes of RAM memory and 100 MB of Hard disk memoryNo. of bits in a word: 16No. of lines in distributed program, including test data, etc.: 6912No. of bytes in distributed Program, including test data, etc.: 229 541Distribution format: tar.gzNature of the physical problem: the investigation of transport mechanisms for radioactive substances, through environmental pathways, is very important for radiological protection of populations. One such pathway, associated with the food chain, is the grass-animal-man sequence. The distribution of trace elements in humans and laboratory animals has been intensively studied over the past 60 years [R.C. Pendlenton, C.W. Mays, R.D. Lloyd, A.L. Brooks, Differential accumulation of iodine-131 from local fallout in people and milk, Health Phys. 9 (1963) 1253-1262]. In addition, investigations on the incidence of cancer in humans, and a possible causal relationship to radioactive fallout, have been undertaken [E.S. Weiss, M.L. Rallison, W.T. London, W.T. Carlyle Thompson, Thyroid nodularity in southwestern Utah school children exposed to fallout radiation, Amer. J. Public Health 61 (1971) 241-249; M.L. Rallison, B.M. Dobyns, F.R. Keating, J.E. Rall, F.H. Tyler, Thyroid diseases in children, Amer. J. Med. 56 (1974) 457-463; J.L. Lyon, M.R. Klauber, J.W. Gardner, K.S. Udall, Childhood leukemia associated with fallout from nuclear testing, N. Engl. J. Med. 300 (1979) 397-402]. From the pathways of entry of radionuclides in the human (or animal) body, ingestion is the most important because it is closely related to life-long alimentary (or dietary) habits. Those radionuclides which are able to enter the living cells by either metabolic or other processes give rise to localized doses which can be very high. The evaluation of these internally localized doses is of paramount importance for the assessment of radiobiological risks and radiological protection. The time behavior of trace concentration in organs is the principal input for prediction of internal doses after acute or chronic exposure. The General Multiple-Compartment Model (GMCM) is the powerful and more accepted method for biokinetical studies, which allows the calculation of concentration of trace elements in organs as a function of time, when the flow parameters of the model are known. However, few biokinetics data exist in the literature, and the determination of flow and transfer parameters by statistical fitting for each system is an open problem.Restriction on the complexity of the problem: This version of the code works with the constant volume approximation, which is valid for many situations where the biological half-live of a trace is lower than the volume rise time. Another restriction is related to the central flux model. The model considered in the code assumes that exist one central compartment (e.g., blood), that connect the flow with all compartments, and the flow between other compartments is not included.Typical running time: Depends on the choice for calculations. Using the Derivative Method the time is very short (a few minutes) for any number of compartments considered. When the Gauss-Marquardt iterative method is used the calculation time can be approximately 5-6 hours when similar to 15 compartments are considered. (C) 2006 Elsevier B.V. All rights reserved.

MODEL FOR ASYMPTOTIC D-STATE PARAMETERS OF LIGHT-NUCLEI - APPLICATION TO HE-4

A simple method for calculating the asymptotic D-state observables for light nuclei is suggested. The method exploits the dominant clusters of the light nuclei. The method is applied to calculate the He-4 asymptotic D to S normalization ratio rho(alpha) and the closely related D-state parameter D2alpha. The study predicts a correlation between D2alpha and B(alpha), and between rho(alpha) and B(alpha), where B(alpha) is the binding energy of He-4. The present study yields rho(alpha) congruent-to -0.14 and D2alpha congruent-to -0.12 fm2 consistent with the correct experimental eta(d) and the binding energies of the deuteron, triton, and the alpha particle, where eta(d) is the deuteron D-state to S-state normalization ratio.

(X)over-bar charts with variable parameters

Varying the parameters of the (X) over bar chart has been explored extensively in recent years. In this paper, we extend the study of the (X) over bar chart with variable parameters to include variable action limits. The action limits establish whether the control should be relaxed or not. When the (X) over bar falls near the target, the control is relaxed so that there will be more time before the next sample and/or the next sample will be smaller than usual. When the (X) over bar falls far from the target but not in the action region, the control is tightened so that there is less time before the next sample and/or the next sample will be larger than usual. The goal is to draw the action limits wider than usual when the control is relaxed and narrower than usual when the control is tightened. This new feature then makes the (X) over bar chart more powerful than the CUSUM scheme in detecting shifts in the process mean.

Structural and surface properties of thermally prepared Ti/RhxTi(1-x)Oy electrodes: I - influence of preparation parameters

Electrodes of RhxTi(1-x) O-y nominal composition were prepared by thermal decomposition of the chloride or nitrate precursor salts dissolved in strongly acidic medium and applied by brush to both sides of a Tidegrees support. A systematic study of the influence of calcination temperature and time as well as oxygen flux was conducted. The coatings were characterised by SEM, EDAX, XRD, open circuit potential measurements and cyclic voltammetry (CV). Visible-ultraviolet spectrophotometry was employed to identify the chemical form of the precursor in solution while thermogravimetric analysis (TGA) was used to assess the decomposition temperature ranges. Optimisation of the coating preparation parameters showed coatings obtained from [Rh(H2O)(6)](NO3)(3) precursor dissolved in HNO3 1:2 (v/v) and fired at 430 degreesC for 2 h in a 5 1 min (-1) oxygen stream-furnished stable electrodes having the highest electrochemically active surface area. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

Genetic parameters estimate for milk and mozzarella cheese yield, fat and protein percentage in dairy buffaloes in Brazil

The aim of this study was analyze the (co)variance components and genetic and phenotypic relationships in the following traits: accumulated milk yield at 270 days (MY270,), observed until 305 days of lactation; accumulated milk yield at 270 days (MY270/A) and at 305 days (MY305), observed until 335 days of lactation; mozzarella cheese yield (MCY) and fat (FP) and protein (PP) percentage, observed until 335 days of lactation. The (co)variance components were estimated by Restricted Maximum Likelihood methodology in analyses single, two and three-traits using animal models. Heritability estimated for MY270, MY270/A, MY305, MCY, FP and PP were 0.22; 0.24, 0.25, 0.14, 0.29 and 0.40 respectively. The genetic correlations between MCY and the variables MY270, MY270/A, MY305, PP and FP was: 0.85; 1.00; 0.89; 0.14 and 0.06, respectively. This way, the selection for the production of milk in long period should increase MCY. However, in the search of animals that produce milk with quality, the genetic parameters suggest that another index should be composed allying these studied traits.

Effects of 2 or 5 consecutive exercise days on adipocyte area and lipid parameters in Wistar rats

Background: Exercise has been prescribed in the treatment and control of dyslipidemias and cholesterolemia, however, lipid responses to different training frequencies in hypercholesterolemic men have been inconsistent. We sought to verify if different frequencies of continuous moderate exercise (2 or 5 days/week, swimming) can, after 8 weeks, promote adaptations in adipocyte area and lipid parameters, as well as body weight and relative weight of tissues in normo and hypercholesterolemic adult male rats.Methods: Normal cholesterol chow diet or cholesterol-rich diet (1% cholesterol plus 0.25% cholic acid) were freely given during 8 weeks to the rats divided in 6 experimentals groups: sedentary normal cholesterol chow diet (C); sedentary cholesterol-rich diet (H); 5x per week continuous training normal cholesterol chow diet (TC5) and cholesterol-rich diet (TH5); 2x per week continuos traning normal cholesterol chow diet (TC2) and cholesterol-rich diet (TH2).Results: No changes were observed in lipid profile in normal cholesterol chow diet, but both 2 a 5 days/week exercise improved this profile in cholesterol-rich diet. Body weight gain was lower in exercised rats. Decrease in retroperitoneal and epididymal relative weights as well as reductions in adipocyte areas under all diets types were observed only in 5 days/week, while 2 days/week showed improvements mainly in cholesterol-rich diet rats.Conclusion: Our results confirm the importance of exercise protocols to control dyslipidemias and obesity in rats. The effects of 5 days/week exercise were more pronounced compared with those of 2 consecutive days/week training.

THE PARAMETERS OF THE LEWIS METRIC FOR THE WEYL CLASS

We provide physical interpretation for the four parameters of the stationary Lewis metric restricted to the Weyl class. Matching this spacetime to a completely anisotropic, rigidly rotating, fluid cylinder, we obtain from the junction conditions that one of these parameters is proportional to the vorticity of the source. From the Newtonian approximation a second parameter is found to be proportional to the energy per unit of length. The remaining two parameters may be associated to a gravitational analog of the Aharanov-Bohm effect. We prove, using the Cartan scalars, that the Weyl class metric and static Levi-Civita metric are locally equivalent, i.e., indistinguishable in terms of its curvature.

Genetic parameters of milk, fat, and protein yields in the first three lactations, using an animal model and restricted maximum likelihood

Milk, fat, and protein yields of Holstein cows from the States of New York and California in the United States were used to estimate (co)variances among yields in the first three lactations, using an animal model and a derivative-free restricted maximum likelihood (REML) algorithm, and to verify if yields in different lactations are the same trait. The data were split in 20 samples, 10 from each state, with means of 5463 and 5543 cows per sample from California and New York. Mean heritability estimates for milk, fat, and protein yields for California data were, respectively, 0.34, 0.35, and 0.40 for first; 0.31, 0.33, and 0.39 for second; and 0.28, 0.31, and 0.37 for third lactations. For New York data, estimates were 0.35, 0.40, and 0.34 for first; 0.34, 0.44, and 0.38 for second; and 0.32, 0.43, and 0.38 for third lactations. Means of estimates of genetic correlations between first and second, first and third, and second and third lactations for California data were 0.86, 0.77, and 0.96 for milk; 0.89, 0.84, and 0.97 for fat; and 0.90, 0.84, and 0.97 for protein yields. Mean estimates for New York data were 0.87, 0.81, and 0.97 for milk; 0.91, 0.86, and 0.98 for fat; and 0.88, 0.82, and 0.98 for protein yields. Environmental correlations varied from 0.30 to 0.50 and were larger between second and third lactations. Phenotypic correlations were similar for both states and varied from 0.52 to 0.66 for milk, fat and protein yields. These estimates are consistent with previous estimates obtained with animal models. Yields in different lactations are not statistically the same trait but for selection programs such yields can be modelled as the same trait because of the high genetic correlations.