Fadiga de grampos de retenção em prótese parcial removível. Efeito de ligas, espessuras e técnicas de fusão. Parte I.

The authors looked for the verification of the fatigue of retentive clasps utilized on the removable partial denture. According to this, it was idealized and built on assay machine, that through movements, simulate the insertion and removal of the clasp for a pattern tooth, manufactured on cobalt-chromium which has all the preparation normally utilized to the correct confection of this type of prosthesis. It was utilized three different commercial alloys based on cobalt-chromium: L1-Biosil; L2-Steldent; L3-Duracron. It was utilized the T clasp of Roach, with was tested upon three different proportions among width and thickness: E1-1.7;E2-2.0 and E3-2.3 and was casted through two casting techniques: F1-oxygen-gas and F2-oxygen-acetylene. The clasps were tested on the machine, which allowed the reading of the number of insertion and removal cycles made until fatigue appeared. The obtained results were submitted to the statistic analysis and the authors concluded that: a) L3 (Duracrom) obtained the best results followed by L1 (Biosil) and finally L3 (Steldent); b) among the analyzed thickness, the best results were obtained by E3, followed by E2 and after this E1; c) form the casting techniques, F2 gave us the best results.

Fadiga de grampos de retenção em prótese parcial removível. Efeito de ligas, espessuras e técnicas de fusão. Parte II.

The authors tested the T clasp of Roach in three differents proportions among width and thickness: E1-1.7; E2-2.0 and E3-2.3, with a constant length of 15 mm. These clasps were casted with three cobalt-chromium alloys (L1-Biosil; L2-Steldent and L3-Duracrom), through two casting techniques (F1-oxygen-gas and F2-oxygen-acetylene). The fatigue of the clasps were verified by using and assay machine, that through movements, simulate the insertion and removal of the clasps for a pattern which were obtained from a premolar, prepared in a surveyor. This machine detect the fatigue of the clasps and count the number of cycles of insertion and removal realized. The obtained results of the interaction between the analysed factors, were submitted to the statistic analysis and the authors concluded that: a) the interaction of factors, Alloy x Thickness, Alloy x Casting Technique and Thickness x Casting Technique did not change the order of effects that the factors showed separately but gave rise to effects of different magnitude for any observed sense; b) the simultaneous interaction of the factors Alloy x Thickness x Casting Technique confirmed the superiority of the L3 alloy, the thickness E3 and the F2 casting technique.

Produção de biomassa por fungos Filamentosos em meio de vinhaça de cana-de-açúcar suplementado com melaço

Three species of filamentous fungi, Aspergillus niger, Penicillium fellutanum and Mucor hiemalis, were selected and cultivated in vinasse media with different addition of molasses, pasteurized to 85°C for 30 minutes and with pH = 5.0. The microorganisms, previously adapted to the respective medium for 48 hours, from a solution of 107 spores.ml-1, were cultivated in pure and mixed cultures in Erlenmeyer vessel of 500ml, to 30°C, with constant agitation of 170 rpm, for 24, 48 and 72 hours, with four repetition for each samples. The biomass was separated by vacuum filtration in filter Whatman #1 and dried in oven at 105°C until right weight, the obtained liquid was submited to COD analysis. The datas were statistically analysed using a response surface methodology, to improve the effect on the molasses proportion and culture time, in the biomass production by microorganism in research. According to the obtained results (5.02% of molasses, 55.59h, 70% of spores solution of A. niger and 30% of spores solution of P. fellutanum), cultivating was carried out in Microferm Fermentor New Brunswick for 48 hours at 300 rpm, aired at 1v/v/m, using 5 liters of medium added with 5.0% of molasses on the conditions above described. The average of the results obtained (6.81g.l-1) was higher than the confidence interval (5.937 ; 6.369) and was inside the prediction interval (4.471 ; 7.834) both of them significant at 95% by the statistical test employed.

The effects of pre-planting refrigeration on bulbs over the development and yield of garlic 'Chines', 'Contestado' and 'Quiteria'

The objective of this research uas to evaluate the effect of five pre-planting refrigeration periods previously to the cloves planting (0,10,20, 30 and 40 days at a temperature of 4.0 ± 1° C and three garlic cultivars ('Chines', 'Contestado' and 'Quiteria') uere used. According to the obtained results it was observed that the best preplanting refrigeration period was dependent upon the cultivar behavior. For the 'Chines' well adapted to the region, there was no effect of the pre-planting refrigeration period up to 30 days after treatment on the plant height, bulb weight, and total bulb production. 'Contestado' the best pre-planting refrigeration period was 40 days however, there was no statistical difference among 30 and 40, days for the 'Quiteria'. For both cultivars pre-planting refrigeration periods under 20 days, there was no clove's formation.

Concept of Matching Parallelepiped and its use in the correspondence problem

In this paper, the concept of Matching Parallelepiped (MP) is presented. It is shown that the volume of the MP can be used as an additional measure of `distance' between a pair of candidate points in a matching algorithm by Relaxation Labeling (RL). The volume of the MP is related with the Epipolar Geometry and the use of this measure works as an epipolar constraint in a RL process, decreasing the efforts in the matching algorithm since it is not necessary to explicitly determine the equations of the epipolar lines and to compute the distance of a candidate point to each epipolar line. As at the beginning of the process the Relative Orientation (RO) parameters are unknown, a initial matching based on gradient, intensities and correlation is obtained. Based on this set of labeled points the RO is determined and the epipolar constraint included in the algorithm. The obtained results shown that the proposed approach is suitable to determine feature-point matching with simultaneous estimation of camera orientation parameters even for the cases where the pair of optical axes are not parallel.

Feeding activity of Callinectes ornatus Ordway, 1863 and Callinectes danae Smith, 1869 (Crustacea, Brachyura, Portunidae) in Ubatuba, SP, Brazil

The feeding activity along the day cycle and the time consumed for extracellular digestion were evaluated in the portunids C. ornatus and C. danae. Swimming crabs were obtained from trawling in Ubatuba bay, São Paulo, Brazil, during both the rainy and dry seasons. In each season, daily scheduled samples were taken at dawn (±6 h), noon (±12 h), dusk (±18 h) and midnight (±24 h). All individuals were dissected and the degree of stomach replenishment was recorded. In order to estimate the time elapsed for extracellular digestion, crabs were fed, and groups were dissected at 30 min intervals to check the conditions of their stomachs. In general, both species show a higher feeding activity during periods of lower light intensity, as evidenced by an increased percentage of full stomachs in dusk and midnight samples. The obtained results support higher feeding activity at night in these species and indicate short time for extracellular digestion, not exceeding 8 h. Nevertheless, full stomachs were recorded in all sampling schedules. In this case, it should be considered that elimination of certain food items such as fish bones, mollusk shells and carapace fragments of crustaceans could take more time than other items. Additionally, some crab species could require a cycle of cell replacement in the midgut gland epithelium until they can take their next meal.

Investigations into the use of the finite element method and artificial neural networks in the non-destructive analysis of metallic tubes

This work presents an investigation into the use of the finite element method and artificial neural networks in the identification of defects in industrial plants metallic tubes, due to the aggressive actions of the fluids contained by them, and/or atmospheric agents. The methodology used in this study consists of simulating a very large number of defects in a metallic tube, using the finite element method. Both variations in width and height of the defects are considered. Then, the obtained results are used to generate a set of vectors for the training of a perceptron multilayer artificial neural network. Finally, the obtained neural network is used to classify a group of new defects, simulated by the finite element method, but that do not belong to the original dataset. The reached results demonstrate the efficiency of the proposed approach, and encourage future works on this subject.

Simulation of active control using fuzzy logic applied to a pulse combustor

This work analyzes an active fuzzy logic control system in a Rijke type pulse combustor. During the system development, a study of the existing types of control for pulse combustion was carried out and a simulation model was implemented to be used with the package Matlab and Simulink. Blocks which were not available in the simulator library were developed. A fuzzy controller was developed and its membership functions and inference rules were established. The obtained simulation showed that fuzzy logic is viable in the control of combustion instabilities. The obtained results indicated that the control system responded to pulses in an efficient and desirable way. It was verified that the system needed approximately 0.2 s to increase the tube internal pressure from 30 to 90 mbar, with an assumed total delay of 2 ms. The effects of delay variation were studied. Convergence was always obtained and general performance was not affected by the delay. The controller sends a pressure signal in phase with the Rijke tube internal pressure signal, through the speakers, when an increase the oscillations pressure amplitude is desired. On the other hand, when a decrease of the tube internal pressure amplitude is desired, the controller sends a signal 180° out of phase.

Contribuição ao protocolo de controle de qualidade da própolis e de seus extratos

A quality control protocol for the analysis of propolis and its extracts is proposed in the present work. Propolis of Apis mellifera L. bees collected in beehives of an apiary located in the northwest of the Paraná State was triturated and submitted to the following analysis: particles medium size determination, loss of dry, ashes drift, waxes drift, drift of extractive (in water and in ethanol) and total flavonoids drift determination. Propolis ethanolic extracts (96 °GL) at 10% (w/w) and at 30% (w/w) were prepared and submitted to the determination of the pH, relative density, dry residue, alcoholic drift and total flavonoids drift determination. Propolis was analyzed, through High Performance Liquid Cromatography (HPLC). Comparing the obtained results with other works, it was observed that is possible to establish the intervals of values for parameters in order to evaluate the quality of a propolis sample and its extracts.

X-ray-induced conductivity in iron-doped lithium niobate crystals

Illumination of photorefractive, iron-doped lithium niobate crystals (LiNbO 3:Fe) with x-rays generates a conductivity that we determine from the speed of hologram erasure. The doping levels of the crystals and the acceleration voltage of our x-ray tube are varied. A theoretical model is presented, which describes the obtained results. A decrease of the conductivity with increasing Fe 2+ concentration can be explained by assuming that holes are the dominant charge carriers for this short-wavelength illumination.

Geo(anthropo)genic factors affecting the radioactivity in groundwaters from Guarani aquifer, Brazil

This investigation was carried out within the Paraná sedimentary basin, involved the sampling of 77 pumped tubular wells, and was realized with the puipose of evaluating the radioactivity in the Brazilian part of Guarani (Botucatu-Pirambóia, Tacuarembó, Misiones) aquifer. The radioactivity due to nuclides belonging to uranium and thorium series decay was investigated in terms of the uranium isotopes 234U and 238U, radon (222Rn), and the radium isotopes 226Ra and 228Ra. The obtained results were compared with the maximum permissible concentration limits in drinking water defined by the Brazilian national standard, as well with the guidelines for drinking water quality established by the World Health Organization. The importance of water-rock/soil interactions was considered in order to explain most of the obtained data.

In vitro antifungal susceptibility of Candida spp. isolates from patients with chronic periodontitis and from control patients

Superinfection by Candida can be refractory to conventional periodontal treatments in specific situations, such as in immunocompromised patients. In these cases, the systemic therapy with antifungal drugs could be indicated. The aim of this study was to analyse antifungal susceptibility of Candida spp. strains isolated from chronic periodontitis patients and from control individuals. A total of 39 C. albicans isolates, 9 C. tropicalis, 2 C. glabrata and 5 Candida spp. from control individuals and 30 C. albicans, 3 C. tropicalis and 2 C. glabrata from periodontitis patients were tested. In the control group, 1 isolate of C. glabrata was resistant to ketoconazole and 1 Candida spp. was resistant to amphotericin B, ketoconazole and miconazole. Among the isolates of periodontitis group, 1 (3.33%) C. albicans isolate was resistant to flucytosine and ketoconazole. According to the obtained results, it could be concluded that fluconazole was the most effective drug against the several Candida species studied. There were not expressive differences in the susceptibility of isolates from periodontitis patients or from control individuals.

Effect of ceramic surface treatment on the microtensile bond strength between a resin cement and an alumina-based ceramic

Purpose: The objective of this study was to test the following hypothesis: the silica coating on ceramic surface increases the bond strength of resin cement to a ceramic. Materials and Methods: In-Ceram Alumina blocks were made and the ceramic surface was treated: G1 - sandblasting with 110-μm aluminum oxide particles; G2 - Rocatec System: tribochemicai silica coating (Rocatec-Pre powder + Rocatec-Plus powder + Rocatec-Sil); G3 - CoJet System: silica coating (CoJet-Sand) + ESPE-Sil. The ceramic blocks were cemented to composite blocks with Panavia F resin cement (under a load of 750 g/1 min). The cemented blocks were stored in distilled water at 37°C for 7 days and sectioned along the x and y axes with a diamond disk. Samples with an adhesive area of ca 0.8 mm 2 (n = 45) were obtained. The samples were attached to an adapted device for the microtensile test, which was performed in a universal testing machine (EMIC) at a crosshead speed of 1 mm/min. Results: The obtained results were submitted to ANOVA and Tukey's test. Mean values of tensile strength (MPa) and standard deviation values were: (G1) 16.8 ± 3.2; (G2) 30.6 ± 4.5; (G3) 33.0 ± 5.0. G2 and 63 presented greater tensile strength than G1. There was no significant difference between G2 and G3. All the failures took place at the ceramic/resin cement interface. Conclusion: The silica coating (Rocatec or CoJet systems) of the ceramic surface increased the bond strength between the Panavia F resin cement and alumina-based ceramic.

The sugar cane vegetal residues unloaded in the sugar mill: Operational costs and physical characteristics

Brazil produced in 2002/03 season 317.87×106tons of sugar cane stalks and 36.88×106tons of vegetal residues (green leaves, dry leaves and tops) in a planted area of 4.61×106 hectares (ha). These residues have a useful heat of 3,613.14Mcal.t-1. Currently most of this biomass is burned as a pre-harvest practice. The doubt persists in the system type that it must be adopted to pick up, load, transport and unload this biomass at the sugar mill boilers. This study analyzed 22 variables related to operational costs and physical characteristics of these residues in a field situation using a JOHN DEERE® 6850 forage harvester with two different treatments: T1 and T2 (two types of rakes) with 6 repetitions each one. The geographic location of the studied area that belongs to COSTA PINTO MILL (COSAN® Group) is: Latitude 22°40'30S and Longitude 47°36'38W. The adopted methodology was proposed by Ripoli et al. (2002). The obtained results at a 5% level of significance showed that both treatments did not differed significantly between them. Some of the results were, where EBP stands for Oil Equivalent Barrel: Windrowing (T1=US$0.17.EBP-1 and US$9.59.ha-1, T2=US$0.08.EBP-1 and US$4.27.ha-1); Pick up (T1=US$1.31.EBP-1 and US$44.29.ha-1, T2 =US$1.37.EBP-1 and US$48.36.ha-1); Transportation (T1=US$1.27.EBP-1 and US$14,30.ha -1, T2=US$1.33.EBP-1 and US$14,80.ha -1), Unloading at the sugar mill (T1=US$0.30.EBP-1 and US$3.39.ha-1, T2=US$0.32.EBP-1 and US$3.51.ha-1); Total (T1=US$3.05.EBP-1 and US$71.57.ha-1, T2=US$3.10.EBP-1 and US$70.94.ha-1). Confronting the obtained data with the ones in the bibliography, this system revealed itself more expensive than the baling system or the integral harvest system using combines.

Detecção de pistas de aeroporto em imagens orbitais utilizando morfologia matemática

The Brazilian Cartography presents great deficiency in cartographic products updating. This form, Remote Sensins techniques together Digital Processing Images - DPI, are contributing to improve this problem. The Mathematical Morphology theory was used in this work. The principal function was the pruning operator. With its were extracted the interest features that can be used in cartographic process updating. The obtained results are positives and showed the use potential of mathematical morphology theory in cartography, mainly in updating.