Effect of Beverages and Mouthwashes on the Hardness of Polymers Used in Intraoral Prostheses

PurposeThe mechanical properties of acrylic resins used in intraoral prostheses may be altered by frequent exposure to liquids such as beverages and mouthwashes. This study aimed to evaluate the effect of thermocycling and liquid immersion on the hardness of four brands of acrylic resins commonly used in removable prostheses (Onda Cryl, QC-20, Classico, Lucitone).Materials and MethodsFor each brand of resin, seven specimens were immersed in each of six solutions (coffee, cola, red wine, Plax-Colgate, Listerine [LI], Oral B), and seven more were placed in artificial saliva (control). The hardness was tested using a microhardness tester before and after 5000 thermocycles and after 1, 3, 24, 48, and 96 hours of immersion. The results were analyzed using three-way repeated-measures ANOVA and Tukey's test (p < 0.05).ResultsThe hardness of the resins decreased following thermocycling and immersion in the solutions. Specimens immersed in cola and wine exhibited significant decreases in hardness after immersion for 96 hours, although the greatest significant decrease in hardness occurred in specimens immersed in LI. However, according to American Dental Association specification 12, the Knoop hardness of acrylic resins for intraoral prostheses should not be below 15. Thus, the median values of superficial hardness observed in most of the acrylic resins in this study are considered clinically acceptable.ConclusionsThe microhardness of polymers used for intraoral prostheses decreases following thermocycling. Among specimens immersed in beverages, those immersed in cola or wine experienced the greatest decrease in microhardness. Immersion of acrylic resins in LI significantly decreased the microhardness in relation to the initial value. Among the resins assessed, QC-20 exhibited the lowest initial hardness.

Comparison of polymers and ceramics in new and discarded electrical insulators: reuse and recycling possibilities

The expansion and maintenance of electricity distribution networks generates large amounts of waste, much of it in the form of discarded insulators that are not reused or recycled. This paper describes the results of tests on used and new ceramic and polymeric insulators to verify if their exposure to weathering justifies their replacement. In new and used ceramic insulators, properties such as contact angle, relative density, porosimetry, dilatometry and X-ray diffraction patterns showed no differences or the differences that were found could not be related to their use. The discarded ceramic material showed high thermal stability, an interesting characteristic for application as chamotte. It can also be reused to replace gravel used in substations. In polymeric insulators, thermogravimetry, differential scanning calorimetry and relative density test results suggest degradation of used material compared to new. This would justify their replacement and discard as waste, but they show little recycling potential.

Physical-chemical characterization of biomass samples for application iin pyrolysis process

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Chemical reduction of carboxyl groups in heparin abolishes its vasodilatory activity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of active recombinant eIF5A: reconstitution in E. coli of eukaryotic hypusine modification of eIF5A by its coexpression with modifying enzymes

Eukaryotic translation initiation factor 5A (eIF5A) is the only cellular protein that contains the polyamine-modified lysine, hypusine [Nε-(4-amino-2-hydroxybutyl)lysine]. Hypusine occurs only in eukaryotes and certain archaea, but not in eubacteria. It is formed post-translationally by two consecutive enzymatic reactions catalyzed by deoxyhypusine synthase (DHS) and deoxyhypusine hydroxylase (DOHH). Hypusine modification is essential for the activity of eIF5A and for eukaryotic cell proliferation. eIF5A binds to the ribosome and stimulates translation in a hypusine-dependent manner, but its mode of action in translation is not well understood. Since quantities of highly pure hypusine-modified eIF5A is desired for structural studies as well as for determination of its binding sites on the ribosome, we have used a polycistronic vector, pST39, to express eIF5A alone, or to co-express human eIF5A-1 with DHS or with both DHS and DOHH in Escherichia coli cells, to engineer recombinant proteins, unmodified eIF5A, deoxyhypusine- or hypusine-modified eIF5A. We have accomplished production of three different forms of recombinant eIF5A in high quantity and purity. The recombinant hypusine-modified eIF5A was as active in methionyl-puromycin synthesis as the native, eIF5A (hypusine form) purified from mammalian tissue. The recombinant eIF5A proteins will be useful tools in future structure/function and the mechanism studies in translation.

Relationship between the surface chemical composition of implants and contact with the substrate

The purpose of the study was to use scanning electron microscopy and energy dispersive x-ray spectrometry to assess possible morphologic and chemical changes after performing double-insertion and pullout tests of implants of different shapes and surface treatments. Four different types of implants were used—cylindrical machined-surface implants, cylindrical double-surface–treated porous implants, cylindrical surface-treated porous implants, and tapered surface-treated porous implants—representing a total of 32 screws. The implants were inserted into synthetic bone femurs, totaling 8 samples, before performing each insertion with standardized torque. After each pullout the implants were analyzed by scanning electron microscopy and energy dispersive x-ray spectrometry using a universal testing machine and magnified 35 times. No structural changes were detected on morphological surface characterization, only substrate accumulation. As for composition, there were concentration differences in the titanium, oxygen, and carbon elements. Implants with surface acid treatment undergo greater superficial changes in chemical composition than machined implants, that is, the greater the contact area of the implant with the substrate, the greater the oxide layer change. In addition, prior manipulation can alter the chemical composition of implants, typically to a greater degree in surface-treated implants.

Influence of the addition of calcium hydroxide powder on some physical and chemical properties of the sealer MTA fillapex

Objective: This study evaluated the flow, pH and calcium release of MTA Fillapex (G1) or Fillapex plus 10% in weight of calcium hydroxide powder (G2), compared to AH Plus (G3) and Sealapex (G4). Materials and methods:The flow test was performed according to ISO 6876:2001 requirements. The sealers were placed into plastic tubes and immersed in deionized water. After 24 hours, 7, 14 and 28 days, the water of each tube was removed and tested to evaluate the pH values and the level of released calcium. Calcium release values were analyzed statistically by Kruskal Wallis and Dunn tests and pH values analyzed by ANOVA and Tukey tests (? = 5%). Results:G1 presented higher flow among all sealers. The addition of 10% calcium hydroxide into MTA Fillapex reduced the flow (p < 0.05) but, in a level, that is lower than the one recommended for ISO norms. G2 and G4 presented pH values and calcium release higher than G3 (p < 0.05) in all periods. G1 presented pH value higher than G3 (p < 0.05), except in 7 days period (p > 0.05). G4 presented higher pH values than G1 and G2, but the calcium release was similar for all periods (p > 0.05). G3 presented lower calcium release among all groups (p < 0.05). Conclusion: The addition of 10% calcium hydroxide in MTA Fillapex caused reduction in flow and no negative interference in pH and/or calcium release. However, the obtained flow is different from ISO requirements. Clinical relevance: MTA Fillapex presents levels of flow above the ISO norms. The addition of calcium hydroxide is a suggestion for solving this problem, but the impact of these procedures should be carefully evaluated.

Seasonal effects and antifungal activity from bark chemical constituents of Sterculia apetala (Malvaceae) at Pantanal of Miranda, Mato Grosso do Sul, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Processing yield and chemical composition of rainbow trout (Oncorhynchus mykiss) with regard to body weight

The influence of weight (W) category of the rainbow trout on processing yield and chemical composition of the entire eviscerated fish and fish fillet was analyzed. A completely randomized design was employed for processing variables (W1 = 300 to 370 g and W2 = 371 to 440) coupled to a 2 x 2 factorial scheme for the chemical composition (W1 and W2 and forms of presentation: fillet and whole eviscerated fish). W1 showed higher yield for entire eviscerated fish (83.00%) and head (13.27%), but a lower yield for the viscera (17.00%), when compared to W2. We did not affect abdominal muscle yield, fillet with or without skin, skin percentage and residues. There were significant differences between W for moisture (W1 = 72.30% and W2 = 71.15%) and lipids (CP1 = 7.96% and CP2 = 9.04%) rates. Fillet moisture contents (73.74%) and crude protein (19.05%) were higher (p < 0.01) than for entire eviscerated fish (69.71% and 17.81%, respectively). Ash (2.15%) and lipid (10.48%) rates were higher (p < 0.01) for entire fish when compared to those of fillets (1.16% and 6.52%, respectively). The slaughter of fish weighing between 300 and 370 g and their fillets are more adequate for the market.

In vitro antibacterial and chemical properties of essential oils including native plants from Brazil against pathogenic and resistant bacteria

The antimicrobials products from plants have increased in importance due to the therapeutic potential in the treatment of infectious diseases. Therefore, we aimed to examine the chemical characterisation (GC-MS) of essential oils (EO) from seven plants and measure antibacterial activities against bacterial strains isolated from clinical human specimens (methicillin-resistant Staphylococcus aureus (MRSA) and sensitive (MSSA), Escherichia coli, Pseudomonas aeruginosa, Salmonella Typhimurium) and foods (Salmonella Enteritidis). Assays were performed using the minimal inhibitory concentration (MIC and MIC90%) (mg/mL) by agar dilution and time kill curve methods (log CFU/mL) to aiming synergism between EO. EO chemical analysis showed a predominance of terpenes and its derivatives. The highest antibacterial activities were with Cinnamomun zeylanicum (0.25 mg/mL on almost bacteria tested) and Caryophyllus aronzaticus EO (2.40 mg/mL on Salmonella Enteritidis), and the lowest activity was with Eugenia uniflora (from 50.80 mg/mL against MSSA to 92.40 mg/mL against both Salmonella sources and P aeruginosa) EO. The time kill curve assays revealed the occurrence of bactericide synergism in combinations of C. aromaticus and C. zeylanicum with Rosmarinus. officinalis. Thus, the antibacterial activities of the EO were large and this can also be explained by complex chemical composition of the oils tested in this study and the synergistic effect of these EO, yet requires further investigation because these interactions between the various chemical compounds can increase or reduce (antagonism effect) the inhibitory effect of essential oils against bacterial strains.

Neutron activation analysis for chemical characterization of Brazilian oxo-biodegradable plastics

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Agronomic and chemical characteristics of hybrid corn to ensiling

Our aim was to evaluate agronomic and chemical characteristics of corn hybrids to ensiling. It were evaluated nine corn hybrids (MX 300, RB 9308, 2B655, XB 6012, GNZ 2500, PL6890, PRE 32D10, PRE 22T10 e AG 1051), with three replicates. The higher fresh matter yield were observed in the hybrids PL6890 and PRE 32D10, while the dry matter yield was observed in the hybrid PRE 32D10 (13.43 t ha(-1)). The hybrids PRE 32D10 and PRE 22T10 stood out to present higher percent of leaf in relation to whole plant, while the lower percent of stems was found in the hybrids MX 300, 2B655 and XB 6012, however the higher leaves: stems relation was found in XB 6012 (0.49). There was higher CP content in the hybrid PRE 32D10 (9.10% of DM), while the lower NDF (57.78% of DM) and cellulose content (24.27% of DM) were observed in the hybrid GNZ 2500. The hybrid PL6890 presented higher ADF and lignin contents, the others hybrids had values lower. The lower NDIN content was observed in the hybrid RB 9308, while the lower AIDN content occurred on the hybrid 2B655. The lower buffer capacity was observed in the hybrid 2B655 (0.29). There are some differences on chemical composition among the corn hybrids used in this study, however, it is recommended to use the hybrids MX 300, PL6890 and PRE 32D10 for showing higher dry matter yield, which may reflect in the amortization of silage production costs.

Zirconium-methacrylate oxoclusters as new hybrid materials for the modification of epoxy systems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Chemical control of different digitaria insularis populations and management of a glyphosate-resistant population

This study aimed to control different populations of Digitaria insularis by glyphosate herbicide, isolated and mixed, besides the combination of methods (chemical and mechanical) to manage resistant adult plants. Three experiments were conducted, one in pots which were maintained under non-controlled conditions and two under field conditions. In the experiment in pots, twelve populations of D. insularis were sprayed with isolated glyphosate (1.44 and 2.16 kg a.e. ha(-1)) and mixed (1.44 and 2.16 kg a.e. ha(-1)) with quizalofop-p tefuryl (0.12 kg i.a. ha(-1)). The treatment of 1.44 kg a.e. ha(-1) of glyphosate plus 0.12 kg a.i. ha(-1) of quizalofop was sufficient for adequate control (>95%) of all populations. Population 11 (area of grain production in Itumbiara, GO) was considered sensitive to glyphosate. Others populations were moderately sensitive or tolerant to the herbicide. In the field, the plants of D. insularis of one of the experiments were mowed and, in the other, there were not. Eight treatments with herbicides [isolated glyphosate (1.44 and 2.16 kg a.e. ha(-1)) and mixed (1.44 and 2.16 kg a.e. ha(-1)) with quizalofop-p-tefuryl at 0.12 kg a.i. ha(-1)), clethodim at 0.108 kg a.i. ha(-1)) or nicosulfuron at 0.06 kg a.i. ha(-1))] were assessed, in combination with or without sequential application of the standard treatment, sprayed 15 days after the first application. The combination of the mechanic control with the application of glyphosate (2.16 and 1.44 kg a.e. ha(-1)) plus quizalofop-p-tefuryl (0.12 kg a.i. ha(-1)) or clethodim (0.108 kg a.i. ha(-1)), associated to the sequential application, was the most effective strategy for the management of adult plants of resistant D. insularis.

Chemical composition of essential oils from the vegetative and reproductive structures of Copaifera langsdorffii Desf

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)