Modelagem numérica da superfície na geração da planialtimetra segundo dados de quatro equipamentos topogríficos

The aim of this present work was to compare planialtimetric charts obtained from different risings using two different theodolite types, a total station, and a precision level, used as control. Using a total station, an area was marked with clear variations of relief, following a grid, with a distance of 20 meters among stakes. After that, the stakes were read by the total station and two theodolites of different precisions. The geometric leveling was done by a precision level. The data were input in the DataGeosis software and the numerical modelling of the land was made with mesh of maximum rigidity, generating planialtimetric representation for each rising. It was verified, through comparison of the four representations that little variations occur in relation to the control. The closest representation of the control was the planialtimetry based on the data from the total station, in which the representations obtained from the theodolites were identical among themselves. It was concluded that in the process of obtaining detailed planialtimetry of small areas, submitted to the grid, it was not necessary to use composed geometric leveling, reducing work to the exclusive use of a total station or conventional theodolite.

Phytoplankton primary productivity in an urban eutrophic reservoir (São Paulo, Brazil)

The aim of this study was to analyze temporal ..d vertical variation of the biomass and of phytoplankton primary productivity in an urban eutrophic reservoir, in relation to the physical and chemical characteristics of the water. The physical and chemical variables of the water were defined in the limnetic region of the reservoir, at depths of 0.0; 0.5; 1.0; 2.0; 3.0 and 4.0 meters. Three samples were taken to define both the physical and chemical variables, concomitantly with the biomass (chlorophyll-a and phaeophytin) and phytoplankton primary productivity (C-14 method). Based on data obtained on differences in depth of the mixture zone and the euphotic zone, it is hypothesised that, depending on the time of the year, phytoplankton is conditioned by differences in the light and nutrient regimes, which change according to the constant loads of nutrients thrown into the system. The highest concentration of chlorophyll-a in the photic zone of the limnetic region was observed in November 2000 (1,197.3 mg Chl L -1) and the lowest in November 1999 (94.0 mg ChI L -1), whereas the profiles of primary activity of phytoplankton presented the highest rates on the surface of the water column, with values varying from 84.7 (May 2000) to 1,376.7mg C m -3 h -1 (December 2000). Annual primary productivity was calculated at 1,567.0gC m -2y -1, considered euproductive. The primary productivity profiles reported in this study are typical of aquatic eutrophic systems, rich in plankton and with low light penetration. It can be stated that Garças Lake is a system that suffers from anthropogenic impact, through receiving large loads of organic pollution, reflecting on the physical and chemical characteristics of the water and on the high values of biomass and primary phytoplankton activity. © National Institute of Ecology, New Delhi.

Theoretical and experimental evaluation of the influence of the length of drill rods in the SPT-T test

The influence of soil drill rod length on the N value in the SPT-T test has been studied extensively by Mello (1971), Schmertmann & Palacios (1979), Odebrecht et al. (2002) and Cavalcante (2002). This paper presents an analysis of the Standard Penetration Test supplemented with torque measurement (SPT-T). A theoretical study of the resistance of the rod material to torsion and bending indicated that the shear stress caused by the rod self-weight represents less than 1% of that caused by the torsional moment. An experimental study with electric torquemeters attached to a horizontal rod system, as well as two field tests in the vertical direction, were also carried out to compare and substantiate the results. The purpose of these tests was to analyze changes along the length of the rod in response to successive increments at 1-meter intervals. Torque measurements were taken at each increment of the length to ascertain the accuracy of the theoretical data. The difference between the applied torque and the measured torque at the end of rod system was lower than the minimum scale of mechanical torquemeters used in practice.

Infuěncia do relevo na produtividade e custos do harvester

Among the several variables that influence timber harvesting is the slope, which influences the productivity of forest machines. In this experiment the harvester was evaluated technically and economically while cutting and processing eucalyptus activity on different slope classes. The technical analysis included a study of time and movements by the method of continuous time; productivity was determined by the volume in cubic meters of wood processing. The economic analysis included the parameters of operational cost, production cost and energy consumption. The analysis of the data showed that productivity decreased according to the increase of the percent slope inclination, resulting in an effective work hour productivity increase from 18.72 to 39.71 m 3sc, with a mean of operating cost of US$ 78.78 per work hour.

An intelligent system to detect drilling problems through drilled cuttings return analysis

Cuttings return analysis is an important tool to detect and prevent problems during the petroleum well drilling process. Several measurements and tools have been developed for drilling problems detection, including mud logging, PWD and downhole torque information. Cuttings flow meters were developed in the past to provide information regarding cuttings return at the shale shakers. Their use, however, significantly impact the operation including rig space issues, interferences in geological analysis besides, additional personel required. This article proposes a non intrusive system to analyze the cuttings concentration at the shale shakers, which can indicate problems during drilling process, such as landslide, the collapse of the well borehole walls. Cuttings images are acquired by a high definition camera installed above the shakers and sent to a computer coupled with a data analysis system which aims the quantification and closure of a cuttings material balance in the well surface system domain. No additional people at the rigsite are required to operate the system. Modern Artificial intelligence techniques are used for pattern recognition and data analysis. Techniques include the Optimum-Path Forest (OPF), Artificial Neural Network using Multilayer Perceptrons (ANN-MLP), Support Vector Machines (SVM) and a Bayesian Classifier (BC). Field test results conducted on offshore floating vessels are presented. Results show the robustness of the proposed system, which can be also integrated with other data to improve the efficiency of drilling problems detection. Copyright 2010, IADC/SPE Drilling Conference and Exhibition.

Métodos de interpolação para estimar o ph em solo sob dois manejos de café Arábica

There are many methods used to estimate values in places no sampled for construction of contours maps. The aim of this study was to use the methods of interpolation kriging, inverse of the square of the distance and polynomial in the representation of the spatial variability of the pH of the soil in the organic and conventional management in the culture of the coffee plantation. For that, irregular meshes were built for soil sampling in the depth of 0-0,10 meters, totaling 40 points sampling in each area. For gauging of the interpolation methods they were solitary 10% of the total of points, for each area. Initially, the data were appraised through the classic statistics (descriptive and exploratory) and spatial analysis. The method inverse square of the distance and kriging has low error in estimating dados. The method of kriging presented low variation around the average in different managements.

Performance of the CMS hadron calorimeter with cosmic ray muons and LHC beam data

The CMS Hadron Calorimeter in the barrel, endcap and forward regions is fully commissioned. Cosmic ray data were taken with and without magnetic field at the surface hall and after installation in the experimental hall, hundred meters underground. Various measurements were also performed during the few days of beam in the LHC in September 2008. Calibration parameters were extracted, and the energy response of the HCAL determined from test beam data has been checked. © 2010 IOP Publishing Ltd and SISSA.

Sistema especialista para a monitoração do processo de degradação de medidores tipo indução de energia elétrica ativa

This paper presents a methodology and software for hazard rate analysis of induction type watt-hour meters, considering the main variables related with the degradation process of these meters, for the Elektro Electricity and Services SA. The modeling developed to calculate the watt-hour meters hazard rate was implemented in a tool through a user friendly platform, in Delphi language, enabling not only hazard rate analysis, but also a classification by risk range, localization of installation for the analyzed meters, and, allowing, through an expert system, the sampling of induction type watt-hour meters, based on the model risk developed with artificial intelligence, with the mainly goal of follow and manage the process of degradation, maintenance and replacement of these meters. © 2010 IEEE.

Impedance spectroscopy study of solid-state dye-sensitized solar cells with varying Spiro-OMeTAD concentration

This work reports on the changes of performance of solid-state cells dye-sensitized solar cells with the variation of concentration of spiro-OMeTAD between 5% and 25% in the fabrication of the cell. Variations of charge recombination and capacitance correlate with the improvement of current-potential characteristics at increasing spiro-OMeTAD content, which is explained by reduction of transport resistance for hole transport, the increase of charge separation in the dye molecules, and importantly, with the increase of the β-factor in the recombination resistance, that causes a reduction of the diode ideality factor. © 2010 Materials Research Society.

Nanoscale effects and polaronic relaxation in CaCu3Ti 4O12 compounds

In the present communication, by using dielectric spectroscopy measurement, the correlations between Nanosized Barrier Layer Capacitance (NBLC) (Bueno et al. (2009) [7]) and the high frequency polaronic near-Debye dipolar relaxation found in CaCu3Ti4O12 compounds was discussed. The polaronic process was confirmed to be closely associated with the ultrahigh dielectric features of CaCu3Ti4O12 materials and its concomitant dielectric loss. Herein, the shift in relaxation frequency as a function of temperature was used for calculating the activation energy for hopping electronic conduction. The value obtained was 33 meV, an energy whose magnitude is compatible and confirmed the hypothesis of polaronic features for this high frequency dipolar relaxation process. Furthermore, it is shown that the nanosized barrier inferred from the NBLC model has a polaronic feature with dielectric permittivity exiting orthogonally to dielectric loss, a phenomenological pattern that contradicts the normally observed behavior for traditional dielectrics but explain the dielectric and conductivity feature of CaCu3Ti4O12 compounds. © 2010 Elsevier Ltd. All rights reserved.

Optimal phasor measurement units placement for fault location on overhead electric power distribution feeders

This paper proposes a new approach for optimal phasor measurement units placement for fault location on electric power distribution systems using Greedy Randomized Adaptive Search Procedure metaheuristic and Monte Carlo simulation. The optimized placement model herein proposed is a general methodology that can be used to place devices aiming to record the voltage sag magnitudes for any fault location algorithm that uses voltage information measured at a limited set of nodes along the feeder. An overhead, three-phase, three-wire, 13.8 kV, 134-node, real-life feeder model is used to evaluate the algorithm. Tests show that the results of the fault location methodology were improved thanks to the new optimized allocation of the meters pinpointed using this methodology. © 2011 IEEE.

Desenvolvimento inicial de variedades e clones de cana-de- açúcar em Latossolo Vermelho Distrófico, Aparecida do Taboado-MS

In Brazil, as in other sugar cane (Saccharum spp.) producing countries, varieties and clones have been continuously developed and tested in order to obtain varieties better adapted to changes in climate, soils and management, seeking a better performance in soils and climates of low agricultural suitability for the culture. In this study, the initial vegetative growth and performance of five sugar cane clones (CT96-3095, CT95-3079, CT95-1425, CT96-3024, CT92-1882) and two varieties (SP81-3250 and SP91-1049) were evaluated in an environment characterized by soils of low fertility and sandy texture. The experiment was carried out in a randomized design with seven treatments, consisting of the two sugar cane varieties and five clones. The plots contained six 15 meters sugar cane rows with a line spacing of 1.50 m. The average tiller number, tiller leaf area, vegetative cover, shoot biomass and rate of cover between rows of sugarcane were determined through six assessments in the first half of 2008. At the end of the evaluation (116 days after planting) the results showed that the clones (CT96-3095, CT95-3079, CT95-1425, CT96-3024, CT92-1882) were not significantly superior to the two considered varieties (SP81-3250 and SP91-1049).

Suscetibilidade magnética na identificação de compartimentos da paisagem em uma vertente

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A First approach on the new transmission system in northern Brazil

This article shows an analysis of the electrical parameters of a three-phase transmission line section using a relatively new design for steel towers characterized by 280 meters high. These main features, the height of the line conductors and distance between them, are intrinsically related to the longitudinal and transversal parameters of the line. By this means, an analysis was carried out in order to show the electrical variations between a transmission line using the new technology and a conventional 440-kV line through a wide range of frequencies and a variable soil resistivity. © 2012 The Institution of Engineering and Technology.

Paleosuperfícies e perfis bauxíticos no Planalto de Poços de Caldas, São Paulo/Minas Gerais, Brasil

This work has the objective of correlating altitude with the bauxite profiles in the Poços de Caldas Plateau in order to identify paleosurfaces. Then, bauxite profiles found in the Plateau have been classified and mapped through DEM. Three different types of bauxite profiles are highlighted in the area: (1) Rim Profiles which are well-developed and thick and are located in the areas of highest altitude in the Plateau; (2) Plateau Profiles which are not very thick and very clayey, normally appear in the lower portion of the landscape; (3) Reworked Profiles, characterized by bauxite reworked fragments composed by similar materials found in the tops of Rim and Plateau Profiles. After relating altitude to the constituting materials of the bauxite profiles, it is noticed that there are occurrences of Rim Bauxite Profiles located in altitudes of Plateau Profiles and Reworked Profiles located over Rim Profiles, above 1,400 meters of altitude. In the opposite direction, tops of the same elevation are found, where there should be Rim Profiles, there are rocky outcrops observed in field, without any evidence of laterite profiles. It is concluded, therefore, that the elevation rates by themselves, at least in this area, are not good enough references to determine the existence and distribution of paleosurfaces.