Correlation of microcrack fracture size with fatigue cycling on non-crimp fabric/RTM6 composite in the uniaxial fatigue test

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of stitched fabric composite processed by RTM in quasi-static test

Stitched fabrics have been widely studied for potential application in aircraft structures since stitch yarns offer improvements in the out-of-plane mechanical properties and also can save time in the lay up process. The down side of stitch yarns came up in the manufacturing process of fabric in which defects introduced by the needle movement creating fiber-free-zones, fiber breakage and misalignment of fibers. The dry stitched carbon fabric preform has mainly been used in the Resin Transfer Molding (RTM) process which high fiber content is aimed, those defects influence negatively the injection behavior reducing the mechanical properties of final material. The purpose of this research work focused on testing in quasi-static mechanical mode (in-plane tension) of a monocomponent resin CYCOM (R) 890 RTM/carbon fiber anti-symmetric quadriaxial fabric stitched by PE 80Dtex yarn processed by RTM. The evaluation consisted in comparing the scatter of the quasi-static test with the attenuation of ultrasonic maps, which show the path of the resin and possible dry spots considering that interference of yarn in resin flow is detectable in ultrasonic measurement. Microscopic analysis was also considered for further evaluation in case of premature failure. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

A revised taxonomy for time warp based distributed synchronization protocols

This paper presents an improved and updated taxonomy for Time Warp based distributed synchronization protocols. This taxonomy aims to allow the grouping of several optmistic distributed simulation synchronization protocols, with the objective to facilitate the task to decide which protocol is better for a specific simulation.

AMS and grain shape fabric of the Late Palaeozoic diamictites of the Southeastern Paran Basin, Brazil

Diamictites interbedded with marine shales and turbidites onlap the eastern border of the Parana Basin (Southern Brazil). These poorly sorted sediments were deposited during the Permo-Carboniferous glaciation, and their matrix-supported clasts show no preferred orientation. These massive rocks have been studied using anisotropy of magnetic susceptibility (AMS) and grain shape fabric. Hysteresis loops and thermomagnetic measurements show that AMS depends mostly on the paramagnetic clays, but fine ferromagnetic particles also contribute to the anisotropy. The coarse silt to sand grain preferred orientation study supports the use of AMS in describing the diamictite fabric, at least regarding the orientation of the foliation. AMS and grain shape data reveal subhorizontal to weakly inclined magnetic and grain shape foliation parallel to the regional bedding. The magnetic lineations are normally scattered within the foliation plane in agreement with the oblate AMS ellipsoids found in these rocks. Both fabric patterns are consistent with deposition by subaqueous mudflows that were resedimented downslope, with elastic supply from continental sources. The off-vertical grain shape foliation poles suggest that the deposition of diamictites was controlled by the depocentre topography of the Rio do Sul sub-basin.

Effect of fiber surface on flexural strength in carbon fabric reinforced epoxy composites

The effect of carbon fiber surface characteristics on flexural properties of structural composites is studied in this work. Two types of intermediate modulus carbon fibers were used: T800HB and IM7. Results revealed that higher mechanical properties are linked with higher interfacial adhesion. Morphologies and chemical compositions of commercial carbon fibers (CF) were characterized by Fourier Transformed Infra Red (FTIR) and Scanning Electronic Microscopy (SEM). Comparing the results, the T800HB apparently has more roughness, since the IM7 seems to be recovered for a polymeric film. On other hand, the IM7 one shows higher interactivity with epoxy resin system Cycom 890 RTM. Composites produced with Resin Transfer Molding (RTM) were tested on a flexural trial. Interfacial adhesion difference was showed with SEM and Dynamic Mechanical Analyses (DMA), justifying the higher flexural behavior of composites made with IM7 fibers. © 2013 Elsevier B.V. All rights reserved.

Pathogenicity of Metarhizium anisopliae for Ceratitis capitata (Wied.) (Diptera: Tephritidae) in soil with different pesticides

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Revestimento de sementes de milho superdoce (sh2)

A semente de milho doce é leve e rugosa. A rugosidade torna difícil a classificação das sementes quanto à forma e ao tamanho e isso dificulta a semeadura. Uma solução para esse problema seria a utilização da técnica de revestimento. Assim, este trabalho teve por objetivo avaliar diferentes materiais de enchimento, cimentantes e corantes na peletização de sementes de milho superdoce e verificar quais combinações de materiais seriam eficientes na manutenção da qualidade fisiológica das sementes após o armazenamento e que permitissem vazão e distribuição uniformes durante a semeadura. Foram então testados doze materiais de enchimento (calcários 1 e 2, caulim, carvão vegetal ativado, areia, vermiculita, fubá de milho, farinha de trigo, polvilho de mandioca, amido de milho, celite e terra de diatomáceas), dois cimentantes (goma arábica e cascorez extra) e seis corantes (tintas guache, acrílica, plástica e para tecido, corante para alimento e gelatina). As avaliações da qualidade física e fisiológica das sementes revestidas e nuas foram efetuadas por meio dos testes: teor de água, fragmentação, peso de mil sementes, volume aparente e plantabilidade, germinação, primeira contagem da germinação e emergência de plântulas em campo. O revestimento de sementes de milho superdoce proporciona homogeneidade de forma e tamanho às sementes, melhora a vazão e a distribuição dos péletes na semeadura e não compromete a emergência de plântulas em campo depois de quatro meses de armazenamento.

Agentes polinizadores e produção de grãos em cultura de café arábica cv. “Catuaí Vermelho”

Coffee (Coffea arabica L.) plants had the pollination process of their flowers studied in three coffee producing regions in Brazil: the first in Ribeirao Preto, state of São Paulo, in September of 2004, the second in Carmo do Paraiba, in the state of Minas Gerais, in October of 2006, and, the third, in Altinopolis, state of São Paulo, in September of 2007. In all these locations the coffee variety used was the 'Catuai Vermelho'. The pollinator species visiting the flowers, the frequency with which the flowers were visited by the insects, and the type of material collected by them ( nectar and/or pollen) were determined by counts taking place at the first 10 minutes of each hour from 7:00 AM till 6:00 PM during the months mentioned above. To estimate the fructification percentage, 25 branches were identified with color threads and protected with wire frames covered with a nylon fabric to prevent them from being visited by insects. Another group of 25 branches was similarly identified but remained without any covering so that their flowers were thus freely visited by insects. on the average, the most frequent pollinator was the Africanized bee Apis mellifera (73.7%) followed by the bee Trigona spinipes (14.5%), and Tetragonisca angustula (9.5%). The Africanized bee collected nectar and pollen to almost the same extent: 58.5% of the first and 41.5% of the second. To collect nectar, that species increased its visiting frequency up to 1:00 PM. To collect pollen, A. mellifera visited the flowers up to 1:00 PM with frequency peaks between 8:00 and 9:00 AM. T. spinipes collected pollen (58,5%) and nectar (41.5%). T. angustula collected only pollen. The branches freely visited by insects produced 181 grains on the average whereas those covered with the nylon fabric produced only 81 grains, this meaning a reduction of 55.25% in grain production. Coffee grains produced on the freely visited branches had a mean weight (1.13 g) significantly superior to that of those produced on the covered branches (0.94 g).

Ação local do alendronato sódico na reparação óssea de ratos espontaneamente hipertensos (SHR)

FUNDAMENTO: A hipertensão arterial é uma desordem caracterizada por alterações relevantes no tecido ósseo. O alendronato sódico tem indicação no tratamento de doenças ósseas, por causa de sua afinidade pela hidroxiapatita, inibindo as reabsorções ósseas. OBJETIVO: Analisar a ação local do alendronato sódico na reparação óssea de ratos espontaneamente hipertensos (SHR). MÉTODOS: Um defeito ósseo foi criado no fêmur esquerdo de 80 ratos. de acordo com o material utilizado no local, criaram-se quatro grupos: controle (C), amido (Am), alendronato 1 mol (A1) e alendronato 2 mol (A2). Após 7 e 21 dias, os animais foram sacrificados. Foram realizadas análises histológicas e histomorfométricas e os dados foram submetidos a análise de variância (ANOVA) e teste de Tukey (5%). RESULTADOS: Aos 7 dias, observou-se, na área do defeito, tecido conjuntivo com hemorragia e inflamação em todos os grupos. Alguns apresentavam matriz osteóide. Os grupos A1 e A2 apresentaram, ainda, uma rede de fibrina. Aos 21 dias, as trabéculas ósseas fechavam praticamente a extensão do defeito nos grupos C e Am. No grupo A1 de animais machos, observaram-se trabéculas que se irradiavam do canal medular até a área do defeito. Nos grupos A1 e A2, constatou-se apenas a presença de tecido conjuntivo com mínima deposição de osteóide. Um achado histológico marcante foi a formação de tecido ósseo extracortical subperiosteal nos animais dos grupos A1 e A2. CONCLUSÃO: Concluiu-se que a administração do alendronato sódico não contribuiu para o reparo ósseo nos ratos SHR, mas possivelmente tenha sido responsável pelas formações ósseas extracorticais observadas.

Five-dimensional f(R) braneworld models

After incorporating f(R) gravity into the general braneworld sum rules scope, it is shown that some particular class of warped five-dimensional nonlinear braneworld models, which may be interesting for the hierarchy problem solution, still require a negative tension brane. For other classes of warp factors (suitable and not suitable for approaching the hierarchy problem) any negative brane tension in the compactification scheme is not necessary. In this vein, it is argued that, in the bulk f(R) gravity context, some types of warp factors may be useful for approaching the hierarchy problem and for evading the necessity of a negative brane tension in the compactification scheme.

Thermal and mechanical behaviour of sisal/phenolic composites

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of voids on the flexural resistance of the NCF/RTM6 composites

A major difficulty to achieve maximum weight savings in the manufacture of composite structural components, is the tendency of these materials have the formation of voids and cracks in the interior and surface components. In aeronautical applications, controlling the volume fraction of fibers, resins and empty the components of composite is very hard. In this work, composites of epoxy matrix RTM6 reinforced with NCF (non crimp fabric carbon) processed by resin transfer molding (RTM) were characterized for porosity (P-ap) and density (rho(ad)). We used a method based on Archimedes' principle (ASTM C830) and the technique of helium pycnometer. The porosity values were compared with those determined by acid digestion (ASTM D3171). The mechanical properties of processed composites was evaluated by testing on the performing flexural and the results were correlated with the porosity value. All techniques tested to determine void content are satisfactory. The differents results can be justified for heterogeneous void distribution on laminate and differences among techniques characteristics. (C) 2011 Published by Elsevier Ltd. Selection and/or peer-review under responsibility of ICM11

Landmark-based morphometric analysis in selected species of serranid fishes (Perciformes : Teleostei)

Morphological differences among 6 species of marine fishes belonging to 2 subfamilies of the family Serranidae (Serraninae: Dules auriga, Diplectrum formosum, and D, radiale; Epinephelinae: Epinephelus marginatus, Mycteroperca acutirostris, and M. bonaci) were studied by the geometric morphometric method of thin-plate splines and multivariate analysis of partial-warp scores. The decomposition of shape variation into uniform and nonaffine components of shape change indicate that major differences among species are related to both components of shape variation. Significant differences were found among species with respect to the uniform components, but there is no clear separation of taxonomic groups related to these components, and species are instead separated on the basis of body height and caudal peduncle length. Non-uniform changes in body shape, in turn, clearly differentiate the species of Serraninae and Epinephelinae. These shape changes are probably related to differences in habitat and feeding habits among the species.

Towards a hybrid compactification with a scalar-tensor global cosmic string

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)