Comparação do ajuste dos modelos de morgan-mercer-flodin e de johnson-mehl-avrami na reação de precipitação na liga cu-3%al-5%ag

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050°C. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Processamento e caracterização mecânica da liga à base de titânio (Ti-7,5Mo) para confecção de prótese ortopédica

Pós-graduação em Engenharia Mecânica - FEG

Estudo da influência de adições de prata na resistividade elétrica da liga Cu-5%Al

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência de adições de prata na cinética de recristalização da liga CU-5%Al

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência de adições de prata na cinética de precipitação da liga Cu-5%Al

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação das energias de ativação para nucleação de precipitados e difusão da prata na liga cu-2%al com adições de prata

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Reação de precipitação de Ag na liga Cu-8%Al-6%Ag

A reação de precipitação de prata na liga Cu-8%Al-6%Ag foi estudada usando medidas de variação da microdureza com a temperatura e o tempo de envelhecimento, difratometria de raios X (DRX), calorimetria exploratória diferencial (DSC), microscopia eletrônica de varredura (MEV). Os resultados obtidos indicaram que o mecanismo da reação de precipitação da prata é um processo controlado pela difusão da prata e a velocidade desta reação atinge um máximo em torno de 500°C.

Participação da ORF XAC3629 na regulação do operon de resistência a cobre copAB em Xanthomonas citri subsp. citri

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Torneamento de liga de níquel Pyromet 31V (N07032) com ferramentas de metal duro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

O estudo da usinagem em torneamento da superliga à base de níquel Pyromet 31v

The search for materials with higher properties and characteristics (wear resistance, oxidation, corrosion, etc.) has driven research of various materials. Among the materials that are being studied with such properties and characteristics are super alloys based on nickel which has an important role in the aeronautical, automotive, marine, production of gas turbines and now in space vehicles, rocket engineering , experimental aircraft, nuclear reactors, steam-powered plants, petrochemical and many other applications because besides having all the characteristics and properties mentioned above also have an excellent performance at high temperatures. The super alloy based on nickel studied in this work is the super alloy Pyromet 31v normally used in the manufacture of exhaust valves in common engines and diesel engines of high power by cater requirements such as mechanical strength and corrosion resistance at temperatures of approximately 815 ° C. The objective of this work is to produce results to demonstrate more specific information about the real influence of coatings on cutting tools and cutting fluids in turning and thus promote the optimization of the machining of these alloys. The super alloy Pyromet 31v was processed through turning, being performed with various machining parameters such as cutting speed, feed rate, depth in conditions of Minimum Amount of Fluid (MAF), abundant fluid, cutting tools with coating and without coating in early in his work life and with wear. After turning were obtained several samples of chips and the part generated during the machining process, was measured roughness of the material, subsequently made macrostructural analysis of the tools used order to detect possible wear and microstructural analysis of samples collected being that the latter was used for Optical Microscopy, Scanning Electron Microscopy (SEM) and ... (Complete abstract click electronic access below)

Effects of aluminum-copper alloy filtration on photon spectra, air kerma rate and image contrast

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Determinação da temperatura de solubilização da prata em ligas de Cu-Al-Ag por medidas de resistência elétrica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação da usinagem do INCONEL 718

The nickel superalloys are known as being a material with poor machinability, they have some properties like high hardness, good resistance at high temperature, tendency to weld with the tool material at high temperature, etc. In the aerospace, biomedical and petrochemical industry, are increasing the need to use materials that resist to aggressive process and environment. In these uses, it has increased the use of nickel-based superalloys like Inconel 718 and consequently the need to research new techniques and tools to improve the machinability of this material. For the superalloys and resistant alloys at high temperatures is considered that the difficulty in the machining regards to the combination of the relatively high cutting forces and high temperatures that grow during the machine process, causing deformation or breakage of the cutting tool. This work purpose is to develop the study of the machining of external cylindrical turning of the nickel based alloy Inconel 718, using ceramic tools, seeking the optimization of machining this alloy, looking to provide real productive increases without the need of investments in new production means. The machining test were accomplished using commercials hard metal tools and the results were compared each other to find the best tool and the best parameter. The conclusion is that the tool TNMG160408-23 -class 1005- was the better one, when used with the parameter 60_15_08

Estudo das alterações lineares na região cervical de blocos M.O.D. fundidos em liga de cobre alumínio, segundo as técnicas de expansão higroscópica e térmica.

The authors studied linear alterations processed on copper-aluminum casten MOD blocks, obtained from two expansion techniques (termic and hygroscopic by immersion). UNITERMS: Investment expansion. Thermic expansion. Hygroscopic expansion. Casten Technique.