A Strain Gauge Analysis of Microstrain Induced by Various Splinting Methods and Acrylic Resin Types for Implant Impressions

Purpose: The aim of this study was to investigate the level of microstrain that is exerted during polymerization of acrylic resins used for splinting during implant impressions. Material and Methods: Two acrylic resins (GC Pattern Resin, Duralay II) and square transfer coping splinting methods were evaluated by means of strain gauge analysis. Two implants were embedded in a polyurethane block, and the abutments were positioned. Sixty specimens were prepared using two square transfer Copings that were rigidly connected to each other using the acrylic resins. The specimens were randomly divided into three groups of 20 each for the splinting methods: Method 1 was a one-piece method; in method 2, the splint was separated and reconnected after 17 minutes; and in method 3, the splint was separated and reconnected after 24 hours. In each group, half the specimens were splinted with GC Pattern Resin and the other half were splinted with Duralay II. Three microstrain measurements were performed by four strain gauges placed on the upper surface of the polyurethane blocks at 5 hours after resin polymerization for all groups. The data were analyzed statistically. Results: Both resin type and splinting method significantly affected microstrain. interaction terms were also significant. Method 1 in combination with Duralay II produced significantly higher microstrain (1,962.1 mu epsilon) than the other methods with this material (method 2: 241.1 mu epsilon; method 3: 181.5 mu epsilon). No significant difference was found between splinting methods in combination with GC Pattern Resin (method 1: 173.8 mu epsilon; method 2: 112.6 mu epsilon; method 3: 105.4 mu epsilon). Conclusions: Because of the high microstrain generated, Duralay II should not be used for one-piece acrylic resin splinting, and separation and reconnection are suggested. For GC Pattern Resin, variations in splinting methods did not significantly affect the microstrain created. Int J Oral Maxillofac Implants 2012;27:341-345

On Hepatitis C Virus Evolution: The Interaction between Virus and Host towards Treatment Outcome

Background:Hepatitis C is a disease spread throughout the world. Hepatitis C virus (HCV), the etiological agent of this disease, is a single-stranded positive RNA virus. Its genome encodes a single precursor protein that yields ten proteins after processing. NS5A, one of the non-structural viral proteins, is most associated with interferon-based therapy response, the approved treatment for hepatitis C in Brazil. HCV has a high mutation rate and therefore high variability, which may be important for evading the immune system and response to therapy. The aim of this study was to analyze the evolution of NS5A quasispecies before, during, and after treatment in patients infected with HCV genotype 3a who presented different therapy responses.Methods:Viral RNA was extracted, cDNA was synthesized, the NS5A region was amplified and cloned, and 15 clones from each time-point were sequenced. The sequences were analyzed for evolutionary history, genetic diversity and selection.Results:This analysis shows that the viral population that persists after treatment for most non-responder patients is present in before-treatment samples, suggesting it is adapted to evade treatment. In contrast, the population found in before treatment samples from most end-of-treatment responder patients either are selected out or appears in low frequency after relapse, therefore changing the population structure. The exceptions illustrate the uniqueness of the evolutionary process, and therefore the treatment resistance process, in each patient.Conclusion:Although evolutionary behavior throughout treatment showed that each patient presented different population dynamics unrelated to therapy outcome, it seems that the viral population from non-responders that resists the treatment already had strains that could evade therapy before it started. © 2013 Bittar et al.

Species Diversity of Myrmecofauna and Araneofauna Associated with Agroecosystem and Forest Fragments and their Interaction with Carabidae and Staphylinidae (Coleoptera)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Performance of layers submitted to different forced-molting methods and different temperatures

This study was carried out to evaluate the performance and egg quality of laying hens, in their second laying cycle submitted to different forced-molting methods and three environmental temperatures. Six hundred layers were distributed in a completely randomized experimental design with 15 treatments with five replicates of eight birds each, according to 5x3 factorial arrangement (molting methods vs. temperatures). The following forced-molting methods were applied: 90%, 70%, 50% dietary alfalfa inclusion, addition of 2,800 ppm zinc, and feed fasting. Temperatures were: 20 ºC, 27 ºC and 35 ºC. At the end of each period of the second laying cycle, bird performance and egg quality were evaluated. Data were submitted to analysis of variance and means were compared by orthogonal and polynomial contrasts. The highest alfalfa inclusion level (90% alfalfa and 10% basal diet) proved to be efficient as compared to the other methods, independently of temperature.

Genotype by environment interaction for birth and weaning weights of composite beef cattle in different regions of Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Extraction methods and availability of phosphorus for soybean in soils from Parana State, Brazil

In studies on the evaluation of methodologies for the analysis of soil, phosphorus (P) has been the single most studied aspect, due to the complexity of this dynamic element in soil. However, these studies have been limited regarding soil conditions in Paranaa. The present study aimed to evaluate the efficiency of the Mehlich-1, Mehlich-3 and ion exchange resin methods in the evaluation of available P for soybean (Glycine max) in the soils of Paranaa State. Twelve soil samples collected from the upper 0-20 cm were planted with soybean for a period of 42 days in the greenhouse. The ability to extract soil P followed the order of decreasing average amount of extracted P: Mehlich-3 > resin > Mehlich-1. The correlation coefficients between the content of P extracted by Mehlich-1, Mehlich-3 and resin and the amount of P accumulated in the plants were 0.86, 0.90 and 0.93, respectively. Mehlich-1, Mehlich-3 and resin showed similar efficiency in the evaluation of P availability to plants and, under conditions of natural fertility and in soils that had received no application of poorly natural reactive phosphates, can be used to quantify the concentrations of P in the soils of Parana State.

CHARACTERIZATION of RALSTONIA SOLANACEARUM STRAINS FROM BRAZIL USING MOLECULAR METHODS and PATHOGENICITY TESTS

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Understanding the Crystallization Mechanism of a Wollastonite Base Glass Using Isoconversional, IKP Methods and Master Plots

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Beak-trimming methods and their effect on the performance of japanese quail pullets (Coturnix japonica)

This study aimed at verifying if beak-trimming methods in Japanese quail pullets could optimize production by decreasing stress caused by cannibalism. A total number of 816 day-old Japanese quails was distributed in a completely randomized experimental design in a 2 x 3 factorial arrangement, with two beak-trimming ages (14 and 21 days of age) and three beak-trimming sizes (not trimmed, 1/3 trimmed, or 1/2 trimmed), and 4 replicates of 34 birds per replicate. Birds were submitted to the same management and feeding conditions. Weight gain, feed intake, feed conversion ratio, and mortality were evaluated. There was no significant effect of age at beak trimming on the evaluated parameters (P>0.05), as well as no significant interaction between age at beak trimming, and beak-trimming method. There was a significant effect (P<0.01) of trimming size on performance, with the best performance observed in birds not submitted to beak trimming or had 1/2 of the beak trimmed. When the beak was more aggressively trimmed (1/2), parameters were worse. According to the obtained results, it is recommended to trim 1/3 of the beaks, which can be performed either at 14 or 21 days of age.

A CASE tool for the modeling of methods and information systems

MODSI is a multi-models tool for information systems modeling. A modeling process in MODSI can be driven according to three different approaches: informal, semi-formal and formal. The MODSI tool is therefore based on the linked usage of these three modeling approaches. It can be employed at two different levels: the meta-modeling of a method and the modeling of an information system.In this paper we start presenting different types of modeling by making an analysis of their particular features. Then, we introduce the meta-model defined in our tool, as well as the tool functional architecture. Finally, we describe and illustrate the various usage levels of this tool.

Performance of Layers Submitted to Different Forced Molting Methods and Different Temperatures

This study was carried out to evaluate the performance and egg quality of laying hens, in their second laying cycle submitted to different forced-molting methods and three environmental temperatures. Six hundred layers were distributed in a completely randomized experimental design with 15 treatments with five replicates of eight birds each, according to 5x3 factorial arrangement (molting methods vs. temperatures). The following forced-molting methods were applied: 90%, 70%, 50% dietary alfalfa inclusion, addition of 2,800 ppm zinc, and feed fasting. Temperatures were: 20 degrees C, 27 degrees C and 35 degrees C. At the end of each period of the second laying cycle, bird performance and egg quality were evaluated. Data were submitted to analysis of variance and means were compared by orthogonal and polynomial contrasts. The highest alfalfa inclusion level (90% alfalfa and 10% basal diet) proved to be efficient as compared to the other methods, independently of temperature.

Study of the interaction between hydroxymethylnitrofurazone and 2-hydroxypropyl-beta-cyclodextrin

Chagas disease is a serious health problem in Latin America. Hidroxymethylnitrofurazone (NFOH) is a nitrofurazone prodrug more active than nitrofurazone against Trypanosoma cruzi. However, NFOH presents low aqueous solubility, high photodecomposition and high toxicity. The present work is focused on the characterization of an inclusion complex of NFOH in 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD). The complexation with HP-beta-CD was investigated using reversed-phase liquid chromatography, solubility isotherms and nuclear magnetic resonance. The retention behavior was analyzed on a reversed-phase C-18 column, using acetonitrile-water (20/80, v/v) as the mobile phase, in which HP-beta-CD was incorporated as a mobile phase additive. The decrease in the retention times with increasing concentrations of HP-beta-CD enables the determination of the apparent stability constant of the complex (K = 6.2 +/- 0.3 M-1) by HPLC. The solubility isotherm was studied and the value for the apparent stability constant (K = 7.9 +/- 0.2 M-1) was calculated. The application of continuous variation method indicated the presence of a complex with 1:1 NFOH:HP-beta-CD stoichiometry. The photostability study showed that the formation of an inclusion complex had a destabilizing effect on the photodecomposition of NFOH when compared to that of the "free" molecule in solution. The mobility investigation (by NMR longitudinal relaxation time) gives information about the complexation of NFOH with HP-beta-CD. In preliminary toxicity studies, cell viability tests revealed that inclusion complexes were able to decrease the toxic effect (p < 0.01) caused by NFOH. (c) 2008 Elsevier B.V. All rights reserved.

Methods and tools for encoding the WordNet.Br sentences, concept glosses, and conceptual-semantic relations

This paper presents the overall methodology that has been used to encode both the Brazilian Portuguese WordNet (WordNet.Br) standard language-independent conceptual-semantic relations (hyponymy, co-hyponymy, meronymy, cause, and entailment) and the so-called cross-lingual conceptual-semantic relations between different wordnets. Accordingly, after contextualizing the project and outlining the current lexical database structure and statistics, it describes the WordNet.Br editing GUI that was designed to aid the linguist in carrying out the tasks of building synsets, selecting sample sentences from corpora, writing synset concept glosses, and encoding both language-independent conceptual-semantic relations and cross-lingual conceptual-semantic relations between WordNet.Br and Princeton WordNet © Springer-Verlag Berlin Heidelberg 2006.

Interaction between wave and coastal structure: Validation of two lagrangian numerical models with experimental results marine 2011

Numerical modeling of the interaction among waves and coastal structures is a challenge due to the many nonlinear phenomena involved, such as, wave propagation, wave transformation with water depth, interaction among incident and reflected waves, run-up / run-down and wave overtopping. Numerical models based on Lagrangian formulation, like SPH (Smoothed Particle Hydrodynamics), allow simulating complex free surface flows. The validation of these numerical models is essential, but comparing numerical results with experimental data is not an easy task. In the present paper, two SPH numerical models, SPHysics LNEC and SPH UNESP, are validated comparing the numerical results of waves interacting with a vertical breakwater, with data obtained in physical model tests made in one of the LNEC's flume. To achieve this validation, the experimental set-up is determined to be compatible with the Characteristics of the numerical models. Therefore, the flume dimensions are exactly the same for numerical and physical model and incident wave characteristics are identical, which allows determining the accuracy of the numerical models, particularly regarding two complex phenomena: wave-breaking and impact loads on the breakwater. It is shown that partial renormalization, i.e. renormalization applied only for particles near the structure, seems to be a promising compromise and an original method that allows simultaneously propagating waves, without diffusion, and modeling accurately the pressure field near the structure.

Effect of forced-molting methods and rearing temperatures on the performance and organ biometrics of laying hens

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)