Ten years of NO2 comparisons between ground-based SAOZ and satellite instruments (GOME, SCIAMACHY, OMI)

SAOZ (Systeme d'Analyse par Observations Zenithales) is a ground-based UV-Visible zenith-sky spectrometer installed between 1988 and 1995 at a number of NDSC stations at various latitudes on the globe. The instrument is providing ozone and NO2 vertical columns at sunrise and sunset using the Differential Optical Absorption Spectroscopy (DOAS) technique in the visible spectral range. The ERS-2 GOME Ozone Monitoring Experiment (GOME) in 1995 was the first satellite mission to provide a global picture of atmospheric NO 2 with reasonable spatial and temporal resolution. It was then followed by SCanning ImAging spectroMeter for Atmospheric ChartographY (SCIAMACHY) onboard ENVISAT in 2002, and Ozone Monitoring Instrument (OMI) onboard EOS-AURA in 2004, with a similar capacity to monitor total NO 2. All these instruments are nadir viewing mapping spectrometers, applying the DOAS technique in the visible for deriving the NO2 total column. Here we present the results of NO2 long-term comparisons between GOME and SAOZ for the whole period of GOME operation since 1995 at all latitudes - tropics, mid-latitudes and polar regions - in both hemispheres. Comparisons are also shown with the most recently available SCIAMACHY and OMI data in 2004-2005. Overall, the daytime satellite measurements (around noon) are found consistent with sunrise ground-based data, with an average smaller difference at the tropics and mid-latitudes than in the polar areas in the summer. The agreement is even improved after correcting for the NO2 photochemical change between sunrise and the satellite overpass using a box model. However, some seasonal dependence of the difference between ground-based and satellite total NO2 still remains, related to the accuracy of photochemical simulations and the set of NO2 air mass factors used in the retrievals of both systems.

Influence of Excitation Signal on Impedance-based Structural Health Monitoring

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Brazilian solar water heating systems evaluation

The Brazilian National Electricity Conservation Program - PROCEL - runs regular surveys in the electric-energy-consumption market. These studies are used as valuable data to better plan the actions of this program. These data also evaluate the program's performance by identifying the level of penetration of the most efficient electric equipment within the residential sector. PROCEL's main lines of action is to promote and make available the most efficient technologies. Based on the results from the latest survey, it is estimated that 24% of the electric-energy consumption of the residential sector is used by electric shower devices, which instantaneously heat the water that flows through them, normally using an electric resistance of 5 kW. These are an important factor in a country where electric-heating devices are present in about 73% of Brazilian households. Keeping that in mind, the purpose of this work is to present the main results of the Brazilian Solar-Water-Heating-Systems Evaluation, finished in 2010, where 535 installations were visited and more than 50 researchers from different universities participated in the project. Moreover, seven Brazilian cities were selected to be studied. The information was collected from field research and statistically treated. The collected information focused on the adequacy of the project to the household, installation, operation and life cycle of the systems, as well as the users' satisfaction level. Technical questionnaires were developed to summarize all the required information, such as a Web site designed to organize and manage the data collected and a Matlab application that performed the dimensioning and F-chart systems evaluation. Quality indicators were created through a full system monitoring, with thermographic analysis and evaluation of shading influence at the system's efficiency, using the Ecotect software.

A new microcontrolled structural health monitoring system based on the electromechanical impedance principle

This article presents a new method to detect damage in structures based on the electromechanical impedance principle. The system follows the variations in the output voltage of piezoelectric transducers and does not compute the impedance itself. The proposed system is portable, autonomous, versatile, and could efficiently replace commercial instruments in different structural health monitoring applications. The identification of damage is performed by simply comparing the variations of root mean square voltage from response signals of piezoelectric transducers, such as lead zirconate titanate patches bonded to the structure, obtained for different frequencies of the excitation signal. The proposed system is not limited by the sampling rate of analog-to-digital converters, dispenses Fourier transform algorithms, and does not require a computer for processing, operating autonomously. A low-cost prototype based on microcontroller and digital synthesizer was built, and experiments were carried out on an aluminum structure and excellent results have been obtained. © The Author(s) 2012.

Geração automática de estereomodelos a partir de imagens digitais georreferenciadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aplicação integrada de métodos geofísicos em uma área de disposição de resíduos sólidos urbanos em Bauru-SP

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Termite pests in eucalyptus forests of brazil

The termite problem in eucalyptus forest plantations in Brazil has been registered since 1908. The main termite pests can be separated in four groups: a) seedling/sapling termites; b) heartwood termites; c) bark termites and d) wood termites. The termites in the first group attack root and stalk bases of young eucalyptus plants. The most common species are Syntermes spp. and Cornitermes spp. and they are a serious obstacle to early eucalyptus developing. The heartwood termites attack formed trees destroying eucalyptus heartwood. Coptotermes testaceus is the most cited species in reports, but more species probably occur. Plant mortality caused by seedling/sapling termites vary of 10-70 %. There are not effective control methods to heartwood termites. The main seedling/sapling termite control strategy is the chemical barrier around root systems of plants. Nowadays, studies are being carried out to determine monitoring systems to termite infestations. Early results indicate that proportionally, few areas really need insecticide application, due to spatial distribution of termites to be aggregated. Therefore, it is necessary to develope techniques rationalizing insecticide utilization in eucalyptus plantations, to keep production systems feasible and to be suitable for environmental exigencies.

GPS ambiguity resolution and validation under multipath effects: Improvements using wavelets

Integer carrier phase ambiguity resolution is the key to rapid and high-precision global navigation satellite system (GNSS) positioning and navigation. As important as the integer ambiguity estimation, it is the validation of the solution, because, even when one uses an optimal, or close to optimal, integer ambiguity estimator, unacceptable integer solution can still be obtained. This can happen, for example, when the data are degraded by multipath effects, which affect the real-valued float ambiguity solution, conducting to an incorrect integer (fixed) ambiguity solution. Thus, it is important to use a statistic test that has a correct theoretical and probabilistic base, which has became possible by using the Ratio Test Integer Aperture (RTIA) estimator. The properties and underlying concept of this statistic test are shortly described. An experiment was performed using data with and without multipath. Reflector objects were placed surrounding the receiver antenna aiming to cause multipath. A method based on multiresolution analysis by wavelet transform is used to reduce the multipath of the GPS double difference (DDs) observations. So, the objective of this paper is to compare the ambiguity resolution and validation using data from these two situations: data with multipath and with multipath reduced by wavelets. Additionally, the accuracy of the estimated coordinates is also assessed by comparing with the ground truth coordinates, which were estimated using data without multipath effects. The success and fail probabilities of the RTIA were, in general, coherent and showed the efficiency and the reliability of this statistic test. After multipath mitigation, ambiguity resolution becomes more reliable and the coordinates more precise. © Springer-Verlag Berlin Heidelberg 2007.

Fontes de distorções da rede geodésica Brasileira

The Brazilian Geodetic Network started to be established in the early 40's, employing classical surveying methods, such as triangulation and trilateration. With the introduction of satellite positioning systems, such as TRANSIT and GPS, that network was densified. That data was adjusted by employing a variety of methods, yielding distortions in the network that need to be understood. In this work, we analyze and interpret study cases in an attempt to understand the distortions in the Brazilian network. For each case, we performed the network adjustment employing the GHOST software suite. The results show that the distortion is least sensitive to the removal of invar baselines in the classical network. The network would be more affected by the inexistence of Laplace stations and Doppler control points, with differences up to 4.5 m.

Microstructure, crystalline phase, and dielectric property analyses of TiO2 composition with ZrO2 addition

For microwave applications, including mobile and satellite communications, ceramic resonators should have a high dielectric constant, low dielectric losses, and high frequency stability. In this sense, TiO2-ZrO 2 ceramics have been investigated as a function of sintering behavior, phase composition, and microstructure. The ceramics were densified reaching a value of about 86% of theoretical density at 1400°C sintering temperature. The ceramics are prepared by mixing raw materials with the following TiO2-ZrO2 weight % ratio: 100 to 0, 90 to 10, and 80 to 20, respectively. The measured dielectric constants are between 79 and 88 values, while the quality factor due to dielectric losses are between 2820 and 5170. These results point out the influence of Ti/Zr ratio on controlling the dielectric properties. © (2010) Trans Tech Publications.

A PZT-based technique for SHM using the coherence function

This paper presents a new approach for damage detection in structural health monitoring systems exploiting the coherence function between the signals from PZT (Lead Zirconate Titanate) transducers bonded to a host structure. The physical configuration of this new approach is similar to the configuration used in Lamb wave based methods, but the analysis and operation are different. A PZT excited by a signal with a wide frequency range acts as an actuator and others PZTs are used as sensors to receive the signal. The coherences between the signals from the PZT sensors are obtained and the standard deviation for each coherence function is computed. It is demonstrated through experimental results that the standard deviation of the coherence between the signals from the PZTs in healthy and damaged conditions is a very sensitive metric index to detect damage. Tests were carried out on an aluminum plate and the results show that the proposed methodology could be an excellent approach for structural health monitoring (SHM) applications.

Influência da combinação de dados GPS e GLONASS no georreferenciamento de imóveis rurais

The land question has been a widely discussed topic in Brazil, regarding land tenure. Law No. 10.267/01 was a major breakthrough for the agrarian issue. Since then on all rural properties must be georeferenced to the Brazilian Geodetic System (BGS). Therefore, satellite positioning and conventional methods are extensively used. Changes have been occurring in satellite positioning systems due to the addition of new signals in GPS (Global System Positioning), restructuring of GLONASS (Global Orbiting Navigation Satellite System), and the new systems like Galileo and Compass as well. To evaluate the effects of combining GPS and GLONASS data, several batches of processings were performed on different configurations. The data processing was performed to determine the coordinates of points of basic support and those materializing the neighborhood of the rural properties. As a result, it was found that the use of accurate ephemeris in transporting coordinates to support points has no significant influence, since transportation with broadcast ephemeris also meets the accuracy requirements for the Standard Technique for Georreferencing Rural Properties. On the other hand, when GPS and GLONASS data were used, such combination provides the best results. In the case of neighboring points, the use of GPS and GLONASS data is also recommended because such data meet the precision requirement and showed better results than those from where data were processed separately.

Influência da combinação e modernização dos sistemas que integram o GNSS no georreferenciamento de imóveis rurais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modelagem de distorções entre realizações de referenciais geodésicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estimação do diâmetro e rugosidade em um processo de furação utilizando multi sensores e redes neurais artificiais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)