3 resultados para response function
em Universidade Federal do Rio Grande do Norte(UFRN)
Resumo:
The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation
Resumo:
Climate and environmental conditions allowed Brazil to become one of the largest producers of tropical fruits in the world. The São Francisco Valley, over the years, has emerged as the main fruit-producing region of the country, especially mangos and grapes. The mango, which is produced in this region, has reached a good international position, especially in European and American markets. However, the domestic price has absorbed more and more the impact of fluctuations in the international market expectations affecting the production and marketing of producers. The objective of the study is to analyze the transmission ratio of export prices of the mango, with the American market prices and the European Union in the period from 2003 to 2013. It is intended also to analyze the factors affecting the fluctuations of exports Brazilian mango for the main import markets. To achieve the proposed objectives, we used, in the methodology, the autoregressive vector model, in order to find the price transmission mechanism and the mechanisms of impacts through the impulse response function. We also used, the Constant Market Share model, in order to observe the importance of the effects competitiveness, destination, and growth in world trade on the changes of Brazilian mango exports in the period. The data used were obtained from the database of the Ministry of Development and Foreign Trade - MIDIC and FAOSTAT (Food and Agriculture Organization of the United Nations). Among the results, it was found that the Brazilian domestic prices are influenced by the US market price, and that price shocks promoted this market can impact on the growth of the internal prices for several months. It was noted also that the competitiveness effect accounted for the largest portion of the effective growth of Brazilian exports, in other word, the country has improved its competitiveness among the other exporting countries.
Resumo:
The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation
