Oxidação úmida de fenóis com catalisadores de ferro suportado em argilominerais em reator de leito de lama (slurry)

The wet oxidation of organic compounds with CO2 and H2O has been demonstrated to be an efficient technique for effluent treatment. This work focuses on the synthesis, characterization and catalytic performance of Fe-MnO2/CeO2, K-MnO2/CeO2/ palygorskite and Fe/ palygorskite toward the wet oxidative degradation of phenol. The experiments were conducted in a sludge bed reactor with controlled temperature, pressure and stirring speed and sampling of the liquid phase. Experiments were performed on the following operating conditions: temperature 130 ° C, pressure 20.4 atm, catalyst mass concentration of 5 g / L initial concentration of phenol and 0.5 g / L. The catalytic tests were performed in a slurry agitated reactor provided with temperature, pressure and agitation control and reactor liquid sampling. The influences of iron loaded on the support (0.3; 7 and 10%, m/m) and the initial pH of the reactant medium (3.1; 6.8; 8.7) were studied. The iron dispersion on the palygorskite, the phase purity and the elemental composition of the catalyst were evaluated by X-Ray Difraction (XRD), Scanning Electron Microscopy (SEM) and X-Ray Flourescence (XRF). The use of palygorskite as support to increase the surface area was confirmed by the B.E.T. surface results. The phenol degradation curves showed that the Fe3+ over palygorskite when compared with the other materials tested has the best performance toward the (Total Organic carbonic) TOC conversion. The decrease in alkalinity of the reaction medium also favors the conversion of TOC. The maximum conversion obtained from the TOC with the catalyst 3% Fe / palygorskite was around 95% for a reaction time of 60 minutes, while reducing the formation of acids, especially acetic acid. With products obtained from wet oxidation of phenol, hydroquinone, p-benzoquinone, catechol and oxalic acid, identified and quantified by High Performance Liquid Chromatography was possible to propose a reaction mechanism of the process where the phenol is transformed into the homogeneous and heterogeneous phase in the other by applying a kinetic model, Langmuir-Hinshelwood type, with evaluation of kinetic constants of different reactions involved.

Relações interorganizacionais e confiança no setor da carcinicultura: um estudo de caso na camanor produtos marinhos

This study investigated how the types of confidence based on competence and good will act in the formation and maintenance of cooperation relationships between the Camanor and its partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). It used organizational approaches on networks based primarily on studies of Powell (1987, 1990), Das and Teng (2000, 2001), Child (2001) and Contractor and Lorange (2004) which have described the advantages that cooperative relationships can provide, as well as their limits as alternative governance structures. Confidence has been considered an important factor affecting the actions and development of organizations involved in networks or in strategic alliances (ZAHEER; HARRIS, 2006) and is the most appropriate control mechanism in these situations (SYDOW, 1998). Confidence is seen from two different approaches: the economic and the sociological (ZAHEER; HARRIS, 2006). To facilitate the understanding of confidence some typologies have been created, as proposed by Barney and Hansen (1994), Lane (1998), Das and Teng (2000), Child (2001) and Wever, Martens and Vandenbempt (2005). This study made use of the case study as proposition of Yin (2005). Semi-structured interviews were held with pre-determined routes, in a single stage performed in early 2008. The research subjects were owners and / or responsible for Camanor and its business partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). Also secondary data were collected in several sites related to the industry and enterprises studied, in addition to data collected by previous studies conducted by CARCINEREDES (2006). The primary data were analyzed using the analysing technique of the content proposed by Bardin (1994). Regarding the secondary data, they were qualitatively analyzed according to documentary analysis technique (BARDIN, 1994). Thus, through the data collected, could be concluded that although there is confidence based on good faith in relationships(UZZI, 1998; OF; TENG, 2001), their presence does not determine the formation and / or maintenance of a partnership, serves only in order to facilitate the relationship, making them more flexible. The confidence based on competence (DAS; TENG, 2001) influenced the formation and maintenance of relations studied. Because whether or not to form a relationship with another organization it is used the perception of the partner acts, namely the reputation (image) as decision basis. And it is through the verification of the performance of the partner activities that will determine the continuation of the partnership

Influência dos intermediários de distribuição de produtos turísticos no processo de decisão do meio de hospedagem pelo consumidor

This study examines the complex hotel buyer decision process in front of the tourism distribution channels. Its objective is to describe the influence level of the tourism marketing intermediaries, mainly the travel agents and tour operators, over the hotel decision process by the buyer-tourist. The data collection process was done trough a survey with three hundred brazilian tourists hosted in nineteen hotels of Natal, capital of Rio Grande do Norte, Brazil. The data analysis was done using some multivariate statistic techniques as correlation analysis, multiple regression analysis, factor analysis and multiple discriminant analysis. The research characterizes the hotel services consumers profile and his trip, and identifying the distribution channels used by them. Furthermore, the research verifies the intermediaries influence exercised over hotel buyer decision process, looking for identify causality relations between the influence level and the buyer profile. Verifies that information about hotels available on internet reduces the probability that this influence can be practiced; however it was possible identifying those consumers considers this information complementary and non-substitutes than the information from intermediaries. The characteristics of the data do not allow indentifying the factors that constraint the intermediaries influence neither identifying discriminant functions of the specific distribution channel choice by consumers. The study concludes that consumers don t agree in have been influenced by intermediaries or don t know if they have, still considering important to consult them and internet doesn t substitute their function as information source

Obtenção de óxidos a base de níquel e cobalto para reação de oxidação parcial do metano

Nickel-based catalysts supported on alumina have been widely used in various reactions to obtain synthesis gas or hydrogen. Usually, higher conversion levels are obtained by these catalysts, however, the deactivation by coke formation and sintering of metal particles are still problems to be solved. Several approaches have been employed in order to minimize these problems, among which stands out in recent years the use of additives such as oxides of alkali metals and rare earths. Similarly, the use of methodologies for the synthesis faster, easier, applicable on an industrial scale and to allow control of the microstructural characteristics of these catalysts, can together provide the solution to this problem. In this work, oxides with spinel type structure AB2O4, where A represents divalent cation and B represents trivalent cations are an important class of ceramic materials investigated worldwide in different fields of applications. The nickel cobaltite (NiCo2O4) was oxides of spinel type which has attracted considerable interest due to its applicability in several areas, such as chemical sensors, flat panel displays, optical limiters, electrode materials, pigments, electrocatalysis, electronic ceramics, among others. The catalyst precursor NiCo2O4 was prepared by a new chemical synthesis route using gelatine as directing agent. The polymer resin obtained was calcined at 350°C. The samples were calcined at different temperatures (550, 750 and 950°C) and characterized by X ray diffraction, measurements of specific surface area, temperature programmed reduction and scanning electron microscopy. The materials heat treated at 550 and 750°C were tested in the partial oxidation of methane. The set of techniques revealed, for solid preparations, the presence of the phase of spinel-type structure with the NiCo2O4 NixCo1-xO solid solution. This solid solution was identified by Rietveld refinement at all temperatures of heat treatment. The catalyst precursors calcined at 550 and 750°C showed conversion levels around 25 and 75%, respectively. The reason H2/CO was around 2 to the precursor treated at 750°C, proposed reason for the reaction of partial oxidation of methane, one can conclude that this material can be shown to produce synthesis gas suitable for use in the synthesis Fischer-Tropsch process

Síntese e caracterização de óxidos de cério e cobalto obtidos por gel-combustão e Pechini aplicados às reações de oxidação de n-hexano

Oxide type spinel AB2O4 presents structure adjusted for application in the automobile industry. The spinel of cobalt has many practical applications had its excellent physical and chemical properties such as catalyst in hydrocarbon oxidation reaction. The CeO2 has been used in many of these processes because it assigns to a material with excellent thermal resistance and mechanics, high capacity of oxygen stockage (OSC) among others properties. This work deals with the synthesis, characterization and catalytic application of spinel of cobalt and CeO2 with fluorita structure, obtained for method of Pechini and method of Gel-Combustion. The process of Pechini, the puff was obtained at 300 ºC for 2 h in air. In the process of Gel-Combustion the approximately at 350 ºC material was prepared and burnt for Pyrolysis, both had been calcined at 500 ºC, 700 ºC, 900 ºC and 1050 ºC for 2 h in air. The materials of the calcinations had been characterized by TG/DTA, electronic microscopy of sweepings (MEV), spectroscopy of absorption in the infra-red ray (FTIR) and diffraction of X-rays (DRX). The obtained material reaches the phase oxide at 450 oC for Pechini method and 500 °C for combustion method. The samples were submitted catalytic reaction of n-hexane on superficies of materials. The reactor function in molar ration of 0, 85 mol.h-1.g-1 and temperature of system was 450 °C. The sample obtained for Pechini and support in alumine of superficial area of 178,63 m2.g-1 calcined at 700 ºC, give results of catalytic conversions of 39 % and the sample obtained for method of gel-combustion and support in alumina of 150 mesh calcined at 500 ºC result 13 % of conversion. Both method were selective specie C1

Obtenção de polímeros de LCC para aplicação como antioxidante de biodiesel de soja

Biodiesel is a fuel obtained from vegetable oils, such as soy, castorbean, among others. The monoester of fatty acid of these oils have chains with mono, di and tri double connections. The presence of these insaturations are susceptible to oxidization. Antioxidants are substances able to prevent oxidization from oils, fats, fat foods, as well as esters of Alquila( biodiesel). The objective of this work is to summarize a new antioxidant from the Cashew Nut Shell Liquid (CNSL) using the electrolysis technique. A current of 2 amperes was used in a single cell of only one group and two eletrodos of stainless steel 304 in a solution of methanol, together with the eletrolits: acetic acid, sodium chloride and sodium hydroxide, for two hours of agitation. The electrolysis products are characterized by the techniques of cromatography in a thin layer, spectroscopy of infrared and gravimetric analysis. The material was submitted to tests of oxidative stability made by the techniques of spectropy of impendancy and Rancimat (EN 14112). The analyses of characterization suggest that the polimerization of the electrolytic material ocurred. The application results of these materials as antioxidants of soy biodiesel showed that the order of the oxidative stability was obtained by both techniques used

Síntese de catalisadores do tipo LaNixFe1-xO3 como precursores catalíticos para reação oxidação parcial do metano

Nickel-bases catalysts have been used in several reform reactions, such as in the partial oxidation of methane to obtain H2 or syngas (H2 + CO). High levels of conversion are usually obtained using this family of catalysts, however, their deactivation resulting from carbon deposition still remains a challenge. Different approaches have been tested aiming at minimizing this difficulty, including the production of perovskites and related structures using modern synthesis methods capable of producing low cost materials with controlled microstructural characteristics at industrial scale. To establish grounds for comparison, in the present study LaNixFe1-xO3 (x=0, 0.3 or 0.7) perovskites were prepared following the Pechini method and by microwave assisted self-combustion. All samples were sub sequently calcined at 900 °C to obtain the target phase. The resulting ceramic powders were characterized by thermogravimetric analysis, infrared spectroscopy, X ray diffraction, specific area and temperature programmed reduction tests. Calcined samples were also used in the partial oxidation reaction of methane to evaluate the level of conversion, selectivity and carbon deposition. The results showed that the calcined samples were crystalline and the target phase was formed regardless of the synthesis method. According to results obtained by Rietveld refinement, we observed the formation of 70.0% of LaNi0.3Fe0.7O3 and 30.0% of La2O3 for samples LN3F7-900- P, LN3F7-900-M and 41,6% of LaNi0.7Fe0.3O3, 30.7% of La2NiO4 and 27.7% of La2O3 for samples LN7F3-900-P and LN7F3-900-M.Temperature-programmed profiles of the LaNiO3 sample revealed the presence of a peak around 510 °C, whereas the LaFeO3 sample depicted a peak above 1000°C. The highest l evel of methane conversion was obtained for LaNiO3 synthesized by the Pechini method. Overall, catalysts prepared by the Pechini method depicted better conversion levels compared to those produced by microwave assisted self-combustion

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Avaliação de produtos naturais no controle de biofilmes formados em sistema dinâmico

The biofilms microbial forms of association are responsible for generating, accelerating and / or induce the process of corrosion. The damage generated in the petroleum industry for this type of corrosion is significatives, representing major investment for your control. The aim of this study was to evaluate such tests antibiograms the effects of extracts of Jatropha curcas and essential oil of Lippia gracilis Schauer on microrganisms isolated from water samples and, thereafter, select the most effective natural product for further evaluation of biofilms formed in dynamic system. Extracts of J. curcas were not efficient on the complete inhibition of microbial growth in tests type antibiogram, and essential oil of L. gracilis Schauer most effective and determined for the other tests. A standard concentration of essential oil of 20 μL was chosen and established for the evaluation of the biofilms and the rate of corrosion. The biocide effect was determined by microbial counts of five types of microorganisms: aerobic bacteria, precipitating iron, total anaerobic, sulphate reducers (BRS) and fungi. The rate of corrosion was measured by loss of mass. Molecular identification and scanning electron microscopy (SEM) were performed. The data showed reduction to zero of the most probable number (MPN) of bacteria precipitating iron and BRS from 115 and 113 minutes of contact, respectively. There was also inhibited in fungi, reducing to zero the rate of colony-forming units (CFU) from 74 minutes of exposure. However, for aerobic and anaerobic bacteria there was no significant difference in the time of exposure to the essential oil, remaining constant. The rate of corrosion was also influenced by the presence of oil. The essential oil of L. gracilis was shown to be potentially effective

Efeito de preparações de produtos naturais (cravo da índia e tomate) e de um produto sintético na marcação de constituintes sangüineos com tecnécio-99m e na morfologia de hemácias isoladas de sangue de ratos wistar

There are strong interests in the evaluation of the biological effects of natural and synthetic products. Blood constituents labeled with technetium-99m (99mTc) are used in nuclear medicine. The aim of this work was to study the effects of Clove (Caryophyllus aromaticas L.) and OZE (preparation used in the Health Sciences) on the labeling blood constituents with 99mTc and on the morphologic red blood cells (RBC) and the action of an extract of tomato (TO) on the labeling of blood constituents Blood samples were incubated with clove or OZE or TO, stannous chloride and 99mTc. Plasma (P), blood cells (BC), insoluble fractions (IF) of plasma and blood cells were separated. The radioactivity was counted and percentage of radioactivity (%ATI) to each blood fraction was calculated. The shape and morphometric parameter (perimeter/area ratio) were evaluated in the studies with clove and OZE. Clove extract and OZE altered significantly (p<0.05) the %ATI of blood constituents and the shape of red blood cells. However, clove extract not altered the red blood cells perimeter/area ratio. The tomato extract used at the highest concentrations reduced significantly (p<0.05) the %ATI in IF-P, although this extract did not modify the radiolabeling on BC, neither the radioactivity fixation on IFBC. The results indicate that these chemical compounds would have oxidative/chelating actions

Caracterização de superfícies de titânio modificado por oxidação à plasma

Recent years have seen a significant growth in surface modifications in titanium implants, resulting in shorter healing times in regions with low bone density. Among the different techniques, subtraction by chemical agents to increase oxidation has been applied for surface treatment of dental implants. However, this technique is generally unable to remove undesirable oxides, formed spontaneously during machining of titanium parts, raising costs due to additional decontamination stages. In order to solve this problem, the present study used plasma as an energy source to both remove these oxides and oxidize the titanium surface. In this respect, Ti disks were treated by hollow cathode discharge, using a variable DC power supply and vacuum system. Samples were previously submitted to a cleaning process using an atmosphere of Ar, H2 and a mixture of both, for 20 and 60 min. The most efficient cleaning condition was used for oxidation in a mixture of argon (60%) and oxygen (40%) until reaching a pressure of 2.2 mbar for 60 min at 500°C. Surfaces were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), atomic force microscopy (AFM), adhesion and cell proliferation. SEM showed less cell spreading and a larger number of projections orfilopodia in the treated samples compared to the control sample. AFM revealed surface defects in the treated samples, with varied geometry between peaks and valleys. Biological assays showed no significant difference in cell adhesion between treated surfaces and the control. With respect to cell proliferation, the treated surface exhibited improved performance when compared to the control sample. We concluded that the process was efficient in removing primary oxides as well as in oxidizing titanium surfaces

Avaliação in vitro da eficácia de produtos homeopáticos contendo momordica charantia através de bioensaios

Homeopathic medicines have been used for over two hundred years without the examination of their effects on in vivo and in vitro assays, due to the peculiarity of homeopathic preparations, the high dilution, which creates a challenge for the use of usual analytical techniques of quality control of medicine.Although there is scarcity of literature and variety of experiments, recently there have been some studies with few in vitro assays which have shown positive responses when evaluating the mechanism of action of homeopathic medicines which are able to act on a specific system.The present study aims to evaluate the efficacy of homeopathic products containing Momordica charantia through bioassays.Homeopathic products were tested by the MTT to assess cytotoxicity in RAW 264.7 (macrophage-like cells) and in tumor cells HeLa (human cervical adenocarcinoma cells), CHO K1 (Chinese hamster ovary cells), PANC-1 (human pancreas cancer cells) and PC-3 (human prostate cancer cells), dosage of inflammatory mediators NO, TNF-α and IL-6 released by RAW 264.7 cells, analysis of the death process and cell cycle changes of PC-3 by flow cytometry. The data demonstrate that homeopathic products of Momordica charantia did not show cytotoxicity to RAW 264.7, increased the production of inflammatory mediators by RAW 264.7 synergistically with LPS, showed cytotoxicity to PC-3 with change in its cell cycle inhibiting its proliferation, being the 30CH the most potent sample. Correlation studies were conducted in order to evaluate the possible in vitro applicable models to the quality control of homeopathic products with Momordica charantia. The data showed that the best applicable models in assessing the quality are the MTT to assess cytotoxicity in RAW 264.7 and PC-3 in 24 hours for Momordica charantia fruit products and dosage of NO production by RAW 264.7 with and without LPS

Contribuições sobre estudos térmicos (TG/DTG, DTA, DSC e DSC-Fotovisual) da rifampicina e seus principais produtos de degradação

Since its synthesis over 48 years rifampicin has been extensively studied. The literature reports the characterization of thermal events for rifampicin in nitrogen atmosphere, however, no characterization in synthetic air atmosphere. This paper aims to contribute to the thermal study of rifampicin through thermal (TG / DTG, DTA, DSC and DSC - FOTOVISUAL ) and non-thermal (HPLC, XRPD , IR - FTIR , PCA) and its main degradation products ( rifampicin quinone , rifampicin N-oxide 3- formylrifamicin). Rifampicin study was characterized as polymorph form II from techniques DSC, IR and XRPD. TG curves for rifampicin in synthetic air atmosphere showed higher thermal stability than those in N2, when analyzed Ti and Ea. There was characterized as overlapping events melting and recrystallization under N2 with weight loss in the TG curve, suggesting concomitant decomposition. Images DSCFotovisual showed no fusion event and showed darkening of the sample during analysis. The DTA curve in synthetic air atmosphere was visually different from DTA and DSC curves under N2, suggesting the absence of recrystallization and melting or presence only decomposition. The IV - FTIR analysis along with PCA analysis and HPLC and thermal data suggest that rifampicin for their fusion is concomitant decomposition of the sample in N2 and fusion events and recrystallization do not occur in synthetic air atmosphere. Decomposition products studied in an air atmosphere showed no melting event and presented simultaneously to the decomposition initiation of heating after process loss of water and / or solvent, varying the Ti initiating events. The Coats - Redfern , Madsudhanan , Van Krevelen and Herwitz - Mertzger kinetic parameters for samples , through the methods of OZAWA , in an atmosphere of synthetic air and / or N2 rifampicin proved more stable than its degradation products . The kinetic data showed good correlation between the different models employed. In this way we contribute to obtaining information that may assist studies of pharmaceutical compatibility and stability of substances

Análise antropotecnológica do desenvolvimento de novos produtos na produção artesanal : caso das rendeiras de bilro da Vila de Ponta Negra em Natal, RN

Brazilian craft production plays an important role in the generation of employment and income for many families in every state across Brazil. In Natal, Rio Grande do Norte, Brazil, among many types found, identifies itself with the production of bobbin-lace, still practiced in Ponta Negra Village for ancient craftswomens of city that try to preserve the art and tradition of bobbin-lace. This work presents the results of an analysis conducted based in concepts of anthropotechnology, on the effects of a design workshop held with bobbin-lace craftswomen in the village of Ponta Negra in July of 2006. The workshop was intended to propose a new concept of products and a new alternative for production in the activity of the craftswomen, on the premise that the laces could be used as a detail inserted into other industrial products such as shirts, bags, towels, etc. Evaluations after the workshop showed that none of the artisans continued to work, indicating that actions focused solely on products did not generate representative results in the production of bobbin-lace. Evaluations also indicated that knowledge about the artisan's personal and professional characteristics, organization, pace, workload, and cultural and historical issues that permeate the activity are essential to the success of technology transfer, particularly when the transfer affects the craft production as it relates to the inseparable aspects of the craftswomen's work and lifestyle

Análise crítica dos produtos de mobilidade sentada - cadeiras de rodas - utilizados por crianças e adolescentes com paralisia cerebral em Natal/RN e outros municípios do Rio Grande do Norte

The objective of this work is to critically analyze the seated mobility adaptive equipment, wheelchair, used by non-ambulatory children/adolescents diagnosed with cerebral palsy of the quadriplegy type with ages in between 0-18 years old in the municipal city of Natal/RN and of other ones in the state of Rio Grande do Norte. This study is characterized as descriptive as it took into consideration the individualized conditions of each child/adolescent and of their home environment, and also evaluates the condition of the used seated mobility devices such as wheelchairs or strollers. Thirty three (33) subjects which had a wheelchair prescribed by a healthcare professional specialist in adaptive equipment within the past 3 years were selected. A questionnaire was applied through a phone with the patient s primary care giver or parents. The results obtained showed that all the equipment being used had an anatomical seat and back and the tilt system mechanism and even though most of the patients required small individual adjustments upon receiving the wheelchair in order to accommodate to the patients characteristics. From the point of view of the caregiver/parents interviewed, 97% described satisfied with the equipment and report assistance with mobility (97%), comfort (82%) and good posture (82%) as the main positive aspects from the equipment. The results also describe the aspects related to the maintenance, time used and activities developed that were reported by the patients. The conclusion therefore is that in order to select the equipment to meet the needs of the consumer it is necessary that: an appropriate wheelchair prescription takes place, the up-to-date knowledge of equipment available in the market, the appropriate use of the resources from the concession programs of the government that purchase equipment and the establishment of link in between the manufacturers, patients and the caregivers