Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Efetividade da terapia fisica descongestiva na cicatrização de úlceras venosas

A venous ulcer is the most serious clinical manifestation of chronic venous failure, and the most frequent in lower limbs, accounting for 70% of all ulcers. Patients may suffer from this infirmity for several years without healing of the lesion if treatment is inadequate. The aim of this investigation was to verify the effectiveness of decongestive physical therapy in the healing of venous ulcers. This is a quasi-experimental, interventionist study, with paired, non-probabilistic sampling, composed of 50 patients divided into two groups: control and intervention, each composed of 25 patients. Both groups were identically treated for six months with daily dressings and the latter also underwent complex physical therapy consisting of a combination of the following techniques: manual lymphatic drainage, compression bandaging, lower limb elevation, myolymphokinetic exercises and skin care. The study was approved (Protocol no. 59/2007) by the Ethics Committee of the State University of Southeast Bahia. The Mann-Whitney and Chi-square tests were applied for data analysis. After statistical analysis the patients who underwent therapy showed a statistically significant difference with respect to wound contraction starting in the second month of treatment. Compared to the control, the intervention group showed a greater reduction in both pain and edema starting in the third and fourth month of therapy, respectively. To reinforce these findings, the mean percentage of tissue present at the base of the ulcer (granulation/fibrin ratio) was calculated. The intervention group showed greater granulation at the base of the ulcer compared to the control, significant from the second month of treatment on. It was observed in this study that lymphotherapy, when compared between the intervention and control groups, accelerated the healing process, and reduced pain and edema in the affected limbs. It is expected, therefore, that these results widen scientific knowledge and we suggest that this therapy be used 78 not only to reduce lymphedema, but also as a treatment option for venous ulcers, given its easy application and low cost. The data, therefore, demonstrated the importance of basic care on the part of a multiprofessional and transdisciplinary health team involved in the healing process of these infirmities, thereby contributing to better quality of life in these individuals

Sistema de supervisão aérea baseado em navegação visual para detecção de anomalias em instalações de petróleo e gás

This work deals with the development of a prototype of a helicopter quadrotor for monitoring applications in oil facilities. Anomaly detection problems can be resolved through monitoringmissions performed by a suitably instrumented quadrotor, i.e. infrared thermosensors should be embedded. The proposed monitoring system aims to reduce accidents as well as to make possible the use of non-destructive techniques for detection and location of leaks caused by corrosion. To this end, the implementation of a prototype, its stabilization and a navigation strategy have been proposed. The control strategy is based on dividing the problem into two control hierarchical levels: the lower level stabilizes the angles and the altitude of the vehicle at the desired values, while the higher one provide appropriate references signals to the lower level in order the quadrotor performs the desired movements. The navigation strategy for helicopter quadrotor is made using information provided by a acquisition image system (monocular camera) embedded onto the helicopter. Considering that the low-level control has been solved, the proposed vision-based navigation technique treats the problem as high level control strategies, such as, relative position control, trajectory generation and trajectory tracking. For the position control we use a control technique for visual servoing based on image features. The trajectory generation is done in a offline step, which is a visual trajectory composed of a sequence of images. For the trajectory tracking problem is proposed a control strategy by continuous servovision, thus enabling a navigation strategy without metric maps. Simulation and experimental results are presented to validate the proposal

Desenvolvimento de um núcleo versátil e integrado de ferramentas CAD/CAE para a modelagem e simulação de peças mecânicas

Currently there is still a high demand for quality control in manufacturing processes of mechanical parts. This keeps alive the need for the inspection activity of final products ranging from dimensional analysis to chemical composition of products. Usually this task may be done through various nondestructive and destructive methods that ensure the integrity of the parts. The result generated by these modern inspection tools ends up not being able to geometrically define the real damage and, therefore, cannot be properly displayed on a computing environment screen. Virtual 3D visualization may help identify damage that would hardly be detected by any other methods. One may find some commercial softwares that seek to address the stages of a design and simulation of mechanical parts in order to predict possible damages trying to diminish potential undesirable events. However, the challenge of developing softwares capable of integrating the various design activities, product inspection, results of non-destructive testing as well as the simulation of damage still needs the attention of researchers. This was the motivation to conduct a methodological study for implementation of a versatile CAD/CAE computer kernel capable of helping programmers in developing softwares applied to the activities of design and simulation of mechanics parts under stress. In this research it is presented interesting results obtained from the use of the developed kernel showing that it was successfully applied to case studies of design including parts presenting specific geometries, namely: mechanical prostheses, heat exchangers and piping of oil and gas. Finally, the conclusions regarding the experience of merging CAD and CAE theories to develop the kernel, so as to result in a tool adaptable to various applications of the metalworking industry are presented

Adaptação e validação da escala de dependência de exercício físico em versão tradicional e informatizada

While providing physical and psychological benefits, excessive exercise could be or cause a compulsive behavior, making the individual dependent on it. In a parallel discussion, computerized psychological instruments, for a hand, reflects the development of information technology and your applicability to other areas, but also shows little advance for Psychological Assessment. In this perspective, this study aims to adapt the Exercise Dependence Scale (EDS-R) in two formats (paper-and-pencil and computerized) and evaluate evidence of factorial and convergent validity, and reliability of each version and compare them with each other. It is also proposed to observe the relationship of some bio-demographic (Sex, age, frequency, duration and intensity of practice exercise) and the exercise dependence (DEF). For this purpose, 709 regular physical activity practitioners, selected by procedures non-probabilistic sampling, responded a adapted version of EDS-R, Muscle Appearance Satisfaction Scale (MASS), Body Modification Scale (BMS) and a demographic questionnaire, analyzed through Exploratory Factor Analysis, Cronbach's Alpha and not parametric tests. Both the traditional version and the computer showed a seven factors structure, explaining 57 and 62% of the variance, respectively, and Cronbach's alphas of 0.83 and 0.89. Factors were: (1) intentionality, (2) continuity, (3) tolerance, (4) reduction of other activities, (5) lack of control, (6) abstinence and (7) time spent on exercise. Relationships were observed between the Exercise Dependence and the variables: age, diets, consumption of food supplements and medicines for weight change, desire to do plastic surgery and body satisfaction. We observed also a positive correlation between the DEF and the frequency, duration and intensity of exercise, and the factor "Dependence on exercising" from MASS, indicating convergent validity of the EDS-R. Finally, comparisons between the two formats were equivalent, with few changes: computerized version achieved higher DEF scores. Based on these results, it can be concluded that the EDS-R has factorial and convergent validity, reliability, to measure exerceise dependence on traditional e computerized formats. DEF is related to actions used to body modification and behaviors toward exercise. Finally, it was found equivalence between the formats, especially in psychometric parameters, thus suggesting feasibility of a computerized assessment. However, it was observed that the computerized data has sample recruiting strategies more limited

Determinação de parâmetros (sólidos solúveis, pH e acidez titulável) em ameixas intactas usando espectroscopia no infravermelho próximo e seleção de comprimento de onda

The aim of this study was to evaluate the potential of near-infrared reflectance spectroscopy (NIRS) as a rapid and non-destructive method to determine the soluble solid content (SSC), pH and titratable acidity of intact plums. Samples of plum with a total solids content ranging from 5.7 to 15%, pH from 2.72 to 3.84 and titratable acidity from 0.88 a 3.6% were collected from supermarkets in Natal-Brazil, and NIR spectra were acquired in the 714 2500 nm range. A comparison of several multivariate calibration techniques with respect to several pre-processing data and variable selection algorithms, such as interval Partial Least Squares (iPLS), genetic algorithm (GA), successive projections algorithm (SPA) and ordered predictors selection (OPS), was performed. Validation models for SSC, pH and titratable acidity had a coefficient of correlation (R) of 0.95 0.90 and 0.80, as well as a root mean square error of prediction (RMSEP) of 0.45ºBrix, 0.07 and 0.40%, respectively. From these results, it can be concluded that NIR spectroscopy can be used as a non-destructive alternative for measuring the SSC, pH and titratable acidity in plums

Um estudo das condições de percolação e estabilidade em barragens de terra mediante métodos geofísicos: caso do dique de Sant Llorenç de Montgai - Espanha

The monitoring of Earth dam makes use of visual inspection and instrumentation to identify and characterize the deterioration that compromises the security of earth dams and associated structures. The visual inspection is subjective and can lead to misinterpretation or omission of important information and, some problems are detected too late. The instrumentation are efficient but certain technical or operational issues can cause restrictions. Thereby, visual inspections and instrumentation can lead to a lack of information. Geophysics offers consolidated, low-cost methods that are non-invasive, non-destructive and low cost. They have a strong potential and can be used assisting instrumentation. In the case that a visual inspection and strumentation does not provide all the necessary information, geophysical methods would provide more complete and relevant information. In order to test these theories, geophysical acquisitions were performed using Georadar (GPR), Electric resistivity, Seismic refraction, and Refraction Microtremor (ReMi) on the dike of the dam in Sant Llorenç de Montgai, located in the province of Lleida, 145 km from Barcelona, Catalonia. The results confirmed that the geophysical methods used each responded satisfactorily to the conditions of the earth dike, the anomalies present and the geological features found, such as alluvium and carbonate and evaporite rocks. It has also been confirmed that these methods, when used in an integrated manner, are able to reduce the ambiguities in individual interpretations. They facilitate improved imaging of the interior dikes and of major geological features, thus inspecting the massif and its foundation. Consequently, the results obtained in this study demonstrated that these geophysical methods are sufficiently effective for inspecting earth dams and they are an important tool in the instrumentation and visual inspection of the security of the dams

Avaliação das técnicas de soldagem MIG-P CA e MIG-P CC+ aplicadas ao passe de enchimento em liga de alumínio AA5083

For contain beneficial properties, aluminum alloys are gaining more importance in different industrial areas, becoming the subject of study in several academic fields. When related to welding these alloys have some peculiarities that may hinder the union, such as microscopic oxide layer present on the metal surface. The MIG welding process, also known as GMAW, has developed versions that can be effective for welding aluminum. Knowing this, for this paper, two versions of pulsed MIG (CC + and CA) were chosen to evaluate which best suits pass by filling bevel on AA5083 aluminum sheets with 8 and 12 mm thick respectively. Furthermore, two types of wire, ER5087 and ER5183 were evaluated. To evaluate the process and versions of the wires, the high-speed cameras and thermal were used to monitor the metal transfer and the thermal behavior respectively, and the metallographic analysis for macrographic view of the weld beads and non-destructive testing by radiography for observation of possible discontinuities. It was found that the technique of MIG-P CA showed better results ahead of another technique both welding conditions imposed. When connected to the wires, they showed similar results, with uniform cords and seamless

A evolução do turismo no Seridó: uma análise à luz do modelo de Butler

Tourism is configured as an activity that presents constant movement could boost local development in the economic, sociocultural and human in locations with potential for structuring and such. Because it is a dynamic activity, tourism allows changes in its flow, extending the periods of seasonality. To this end, in view of the aforementioned dynamics, it becomes relevant to the presence of tourism planning, initially starting from the government so that it create laws and standards and develop projects for the management of activities in an orderly way, seeking citizen participation, making essential the presence of actors and agents in local tourism, expanding democracy and knowledge of their place of origin. In this scenario, the Ministry of Tourism is emerging with the National Tourism Plan which incorporates among its actions, the Regionalization Program Guide, adopting a model of regional local management, a participatory manner, through the bodies of governance imposed at the poles, and the shares of public policy in their various departments most responsible for promoting tourism in pole Seridó. This scientific work aims to analyze the pole Seridó, under the theory of tourism area life cycle (TALC) proposed by BUTLER (1980), locating actions for tourism and chronology of the locality applied the proposed process activity. For both the methodology is descriptive and exploratory, qualitative approach, historical, descriptive and narrative level, non-probability sampling, using secondary sources, through documents and other records occurred during the planning processes in the region, in order to have access to information related to the planning process of tourism in Seridó, using as a way to research the data collected the technique of content analysis. As a conclusion of this study it is observed that from the survey in relation to the history of tourism in the region, economic activities of livestock, cotton industry, mining and ceramics industry were responsible for the initiation of tourism in the locality through the flow directed to the same, the insertion of the first hotels and performing traditional events, giving rise to the demand for public policies that aided in directing the activity being, therefore, inserted into the engagement phase, the second phase proposed by BUTLER (1980) model, and the study was terminated with suggestions for the continuation of tourism in the region.

Utilização da espectroscopia no infravermelho próximo para o controle de qualidade do camarão (Litopenaeus vannamei)

This work was developed with the objective of proposing a simple, fast and versatile methodological routine using near-infrared spectroscopy (NIR) combined with multivariate analysis for the determination of ash content, moisture, protein and total lipids present in the gray shrimp (Litopenaeus vannamei ) which is conventionally performed gravimetrically after ashing at 550 ° C gravimetrically after drying at 105 ° C for the determination of moisture gravimetrically after a Soxhlet extraction using volumetric and after digestion and distillation Kjedhal respectively. Was first collected the spectra of 63 samples processed boiled shrimp Litopenaeus vannamei species. Then, the determinations by conventional standard methods were carried out. The spectra centered average underwent multiplicative scattering correction of light, smoothing Saviztky-Golay 15 points and first derivative, eliminated the noisy region, the working range was from 1100,36 to 2502,37 nm. Thus, the PLS models for predicting ash showed R 0,9471; 0,1017 and RMSEP RMSEC 0,1548; Moisture R was 0,9241; 2,5483 and RMSEP RMSEC 4,1979; R protein to 0,9201; 1,9391 and RMSEP RMSEC 2,7066; for lipids R 0,8801; 0,2827 and RMSEP RMSEC 0,2329 So that the results showed that the relative errors found between the reference method and the NIR were small and satisfactory. These results are an excellent indication that you can use the NIR to these analyzes, which is quite advantageous, since conventional techniques are time consuming, they spend a lot of reagents and involve a number of professionals, which requires a reasonable runtime while after the validation of the methodology execution using NIR reduces all this time to a few minutes, saving reagents, time and without waste generation, and that this is a non-destructive technique.

Economy of the island of eco-tourism: the role of shark-diving and shark harvesting

Beyond its importance in maintaining ecosystems, sharks provide services that play important socioeconomic roles. The rise in their exploitation as a tourism resource in recent years has highlighted economic potential of non-destructive uses of sharks and the extent of economic losses associated to declines in their population. In this work, we present estimates for use value of sharks in Fernando de Noronha Island - the only ecotouristic site offering shark diving experience in the Atlantic coast of South America. Through the Travel Cost Method we estimate the total touristic use value aggregated to Noronha Island by the travel cost was up to USD 312 million annually, of which USD 91.1 million are transferred to the local economy. Interviewing people from five different economic sectors, we show shark-diving contribute with USD 2.5 million per year to Noronha’s economy, representing 19% of the island’s GDP. Shark-diving provides USD 128.5 thousand of income to employed islanders, USD 72.6 thousand to government in taxes and USD 5.3 thousand to fishers due to the increase in fish consumption demanded by shark divers. We discover, though, that fishers who actually are still involved in shark fishing earn more by catching sharks than selling other fish for consumption by shark divers. We conclude, however, that the non-consumptive use of sharks is most likely to benefit large number of people by generating and money flow if compared to the shark fishing, providing economic arguments to promote the conservation of these species.

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Controle on-line por atributos para o número de não-conformidades no item inspecionado com base em uma sequência de inspeção

This paper proposes a procedure to control on-line processes for attributes, using an Shewhart control chart with two control limits (warning limit and control limit) and will be based on a sequence of inspection (h). The inspection procedure is based on Taguchi et al. (1989), in which to inspect the item, if the number of non-conformities is higher than an upper control limit, the process needs to be stopped and some adjustment is required; and, if the last inspection h, from all items inspected present a number of non-conformities between the control limit and warning limit. The items inspected will suffer destructive inspection, being discarded after inspection. Properties of an ergodic Markov chain are used to get the expression of average cost per item and the aim was the determination of four optimized parameters: the sampling interval of the inspections (m); the constant W to draw the warning limit (W); the constant C to draw the control limit (C), where W £ C, and the length of sequence of inspections (h). Numerical examples illustrate the proposed procedure