Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results

Otimização no uso de martelos e bigornas para quebrar sementes por macacos prego (Cebus flavius e C. libidinosus) no Bioma Caatinga

Recently, capuchin monkeys (Cebus spp.) inhabitants of dry environments and with restriction of fleshy fruits, have been the subject of several studies regarding the use of instruments. During behaviour of using stones to crack open nuts there is evidence of selection of more effective hammers, as well as selection of anvils related to reducing the risk of predation. The aim of this study was to determine whether two groups of capuchin monkeys (C.flavius and and C.libidinosus) inhabitants of the Caatinga of Rio Grande do Norte make choice of hammers and anvils. The record of weight and location of stones indicated active choices of with what (choice of hammers) and where (selection of anvils) to crack open encapsulated seeds. The choice of hammers to break nuts depended on the type and degree of ripeness seed. Thus, smaller seeds were smashed with lighter hammers and larger seeds with heavier hammers. Still, C. flavius was the only species that presented a refinement in the choice of hammers that depended on the ripeness of seeds. For both species of capuchin monkeys studied, the nut-crack sites were not spread in accordance with the spatial distribution of seed-producing species, suggesting that the capuchin monkeys promote active choice of anvils. Thus, in environments with more escape routes through the trees, the nut-crack sites were found further apart than in regions that had less chance of escape through the trees. Also, there was a difference in the spacing of the anvils to depend on the type of seed: sites used to crack larger and more caloric seeds were found farther apart than the sites used to crack smaller and less caloric seeds, suggesting a pattern of avoiding direct competition. We conclude that the capuchin monkeys maximize energy savings and reduced risk of predation and the costs of food competition during the behaviour of using stones to crack open nuts

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results