Simulação do escoamento monofásico em um estágio de uma bomba centrífuga utilizando técnicas de fluidodinâmica computacional

Oil production and exploration techniques have evolved in the last decades in order to increase fluid flows and optimize how the required equipment are used. The base functioning of Electric Submersible Pumping (ESP) lift method is the use of an electric downhole motor to move a centrifugal pump and transport the fluids to the surface. The Electric Submersible Pumping is an option that has been gaining ground among the methods of Artificial Lift due to the ability to handle a large flow of liquid in onshore and offshore environments. The performance of a well equipped with ESP systems is intrinsically related to the centrifugal pump operation. It is the pump that has the function to turn the motor power into Head. In this present work, a computer model to analyze the three-dimensional flow in a centrifugal pump used in Electric Submersible Pumping has been developed. Through the commercial program, ANSYS® CFX®, initially using water as fluid flow, the geometry and simulation parameters have been defined in order to obtain an approximation of what occurs inside the channels of the impeller and diffuser pump in terms of flow. Three different geometry conditions were initially tested to determine which is most suitable to solving the problem. After choosing the most appropriate geometry, three mesh conditions were analyzed and the obtained values were compared to the experimental characteristic curve of Head provided by the manufacturer. The results have approached the experimental curve, the simulation time and the model convergence were satisfactory if it is considered that the studied problem involves numerical analysis. After the tests with water, oil was used in the simulations. The results were compared to a methodology used in the petroleum industry to correct viscosity. In general, for models with water and oil, the results with single-phase fluids were coherent with the experimental curves and, through three-dimensional computer models, they are a preliminary evaluation for the analysis of the two-phase flow inside the channels of centrifugal pump used in ESP systems

Estudo de manejo de águas pluviais urbanas na cidade Natal-Rio Grande do Norte

Urban stormwater can be considered as potential water resources as well as problems for the proper functioning of the manifold activities of the city, resulting from inappropriate use and occupation of the soil, usually due to poor planning of the occupation of the development areas, with little care for the environmental aspects of the drainage of surface runoff. As a basic premise, we must seek mechanisms to preserve the natural flow in all stages of development of an urban area, preserving the soil infiltration capacity in the scale of the urban area, comprising the mechanisms of natural drainage, and noting preserving natural areas of dynamic water courses, both in the main channel and in the secondary. They are challenges for a sustainable urban development in a harmonious coexistence of modern developmental, which are consistent with the authoritative economic environmental and social quality. Integrated studies involving the quantity and quality of rainwater are absolutely necessary to achieve understanding and obtaining appropriate technologies, involving both aspects of the drainage problems and aspects of use of water when subjected to an adequate management of surface runoff , for example, the accumulation of these reservoirs in detention with the possibility of use for other purposes. The purpose of this study aims to develop a computer model, adjusted to prevailing conditions of an experimental urban watershed in order to enable the implementation of management practices for water resources, hydrological simulations of quantity and, in a preliminary way, the quality of stormwater that flow to a pond located at the downstream end of the basin. To this end, we used in parallel with the distributed model SWMM data raised the basin with the highest possible resolution to allow the simulation of diffuse loads, heterogeneous characteristics of the basin both in terms of hydrological and hydraulic parameters on the use and occupation soil. The parallel work should improve the degree of understanding of the phenomena simulated in the basin as well as the activity of the calibration models, and this is supported by monitoring data acquired during the duration of the project MAPLU (Urban Stormwater Management) belonging to the network PROSAB (Research Program in Basic Sanitation) in the years 2006 to 2008

Simulação do escoamento monofásico em um estágio de uma bomba centrífuga utilizando técnicas de fluidodinâmica computacional

Oil production and exploration techniques have evolved in the last decades in order to increase fluid flows and optimize how the required equipment are used. The base functioning of Electric Submersible Pumping (ESP) lift method is the use of an electric downhole motor to move a centrifugal pump and transport the fluids to the surface. The Electric Submersible Pumping is an option that has been gaining ground among the methods of Artificial Lift due to the ability to handle a large flow of liquid in onshore and offshore environments. The performance of a well equipped with ESP systems is intrinsically related to the centrifugal pump operation. It is the pump that has the function to turn the motor power into Head. In this present work, a computer model to analyze the three-dimensional flow in a centrifugal pump used in Electric Submersible Pumping has been developed. Through the commercial program, ANSYS® CFX®, initially using water as fluid flow, the geometry and simulation parameters have been defined in order to obtain an approximation of what occurs inside the channels of the impeller and diffuser pump in terms of flow. Three different geometry conditions were initially tested to determine which is most suitable to solving the problem. After choosing the most appropriate geometry, three mesh conditions were analyzed and the obtained values were compared to the experimental characteristic curve of Head provided by the manufacturer. The results have approached the experimental curve, the simulation time and the model convergence were satisfactory if it is considered that the studied problem involves numerical analysis. After the tests with water, oil was used in the simulations. The results were compared to a methodology used in the petroleum industry to correct viscosity. In general, for models with water and oil, the results with single-phase fluids were coherent with the experimental curves and, through three-dimensional computer models, they are a preliminary evaluation for the analysis of the two-phase flow inside the channels of centrifugal pump used in ESP systems