Atividades Biológicas De Xilana De Sabugo De Milho

The corn cob is an agricultural by-product still little used, this in part due to the low knowledge of the biotechnological potential of their molecules. Xylan from corn cobs (XSM) is a polysaccharide present in greater quantity in the structure of plant and its biotechnology potential is little known. This study aimed to the extraction, chemical characterization and evaluation of biological activities of xylan from corn cobs. To this end, corncobs were cleaned, cut, dried and crushed, resulting in flour. This was subjected to a methodology that combines the use of alkaline conditions with waves of ultrasound. After methanol precipitation, centrifugation and drying was obtained a yield of 40% (g/g flour). Chemical analysis indicated a high percentage of polysaccharides in the sample (60%) and low contamination by protein (0.4%) and phenolic compounds (> 0.01%). Analysis of monosaccharide composition indicated the presence of xylose:glucose:arabinose:galactose:mannose:glucuronic acid in a molar ratio 50:20:15:10:2.5:2.5. The presence of xylan in the sample was confirmed by nuclear magnetic resonance (¹H and ¹³C) and infrared spectroscopy (IR). Tests were conducted to evaluate the antioxidant potential of XSM. This showed a total antioxidant capacity of 48.45 EAA/g sample. However, did not show scavenging activity of superoxide and hydroxyl radical and also reducing power. But, showing a high capacity chelating iron ions with 70% with about 2 mg/mL. The ability to XSM to influence cell proliferation in culture was also evaluated. This polymer did not influence the proliferation of normal fibroblast cells (3T3), however, decreased the rate of proliferation of tumor cells (HeLa) in a dose-dependent, reaching an inhibition of about 50% with a concentration around 2 mg/mL. Analyzing proteins related to cell death, by immunoblotting, XSM increases the amount of Bax, Bcl-2 decrease, increase cytochrome c and AIF, and reduce pro-caspase-3, indicating the induction of cell death induced apoptosis dependent and independent of caspase. XSM did not show anticoagulant activity in the PT test. However, the test of activated partial thromboplastin time (aPTT), XSM increased clotting time at about 5 times with 600 μg of sample compared with the negative control. The presence of sulfate on the XSM was discarded by agarose gel electrophoresis and IR. After carboxyl-reduction of XSM the anticoagulant activity decreased dramatically. The data of this study demonstrate that XSM has potential as antioxidant, antiproliferative and anticoagulant compound. Future studies to characterize these activities of XSM will help to increase knowledge about this molecule extracted from corn and allow their use in functional foods, pharmaceuticals and chemical industries.

Formulação de pastas cimentícias com adição de suspensões de quitosana para cimentação de poços de petróleo

Primary cementing is one of the main operations in well drilling responsible for the mechanical stability and zonal isolation during the production of oil. However, the cement sheath is constantly under mechanical stresses and temperature variations caused by the recovery of heavy oil. In order to minimize fracture and wear of the cement sheath, new admixtures are developed to improve the properties of Portland cement slurries and avoid environmental contamination caused by leaking gas and oil. Polymers with the ability to form polymeric films are candidates to improve the properties of hardened cement slurries, especially their fracture energy. The present study aimed at evaluating the effect of the addition of a chitosan suspension on cement slurries in order to improve the properties of the cement and increase its performance on heavy oil recovery. Chitosan was dissolved in acetic ac id (0.25 M and 2 M) and added to the formulation of the slurries in different concentrations. SEM analyses confirmed the formation of polymeric films in the cementitious matrix. Strength tests showed higher fracture energy compared to slurries without the addition of chitosan. The formation of the polymeric films also reduced the permeability of the slurry. Therefore, chitosan suspensions can be potentially used as cementing admixtures for heavy oil well applications

Compósitos Portland-biopolímeros para cimentação de poços de petróleo

The oil production in mature areas can be improved by advanced recovery techniques. In special, steam injection reduces the viscosity of heavy oils, thus improving its flow to surrounding wells. On the other hand, the usually high temperatures and pressures involved in the process may lead to cement cracking, negatively affecting both the mechanical stability and zonal isolation provided by the cement sheath of the well. The addition of plastic materials to the cement is an alternative to prevent this scenario. Composite slurries consisting of Portland cement and a natural biopolymer were studied. Samples containing different contents of biopolymer dispersed in a Portland cement matrix were prepared and evaluated by mechanical and rheological tests in order to assess their behavior according to API (American Petroleum Institute) guidelines. FEM was also applied to map the stress distribution encountered by the cement at bottom bole. The slurries were prepared according to a factorial experiment plan by varying three parameters, i.e., cement age, contents of biopolymer and water-to-cement ratio. The results revealed that the addition of the biopolymer reduced the volume of free water and the setting time of the slurry. In addition, tensile strength, compressive strength and toughness improved by 30% comparing hardened composites to plain Portland slurries. FEM results suggested that the stresses developed at bottomhole may be 10 to 100 times higher than the strength of the cement as evaluated in the lab by unconfined mechanical testing. An alternative approach is proposed to adapt the testing methodology used to evaluate the mechanical behavior of oilwell cement slurries by simulating the confined conditions encountered at bottornhole

Estudo da segregação gravitacional do processo de injeção de vapor em reservátórios heterogêneos

Due to reservoirs complexity and significantly large reserves, heavy oil recovery has become one of the major oil industry challenges. Thus, thermal methods have been widely used as a strategic method to improve heavy oil recovery. These methods improve oil displacement through viscosity reduction, enabling oil production in fields which are not considered commercial by conventional recovery methods. Among the thermal processes, steam flooding is the most used today. One consequence in this process is gravity segregation, given by difference between reservoir and injected fluids density. This phenomenon may be influenced by the presence of reservoir heterogeneities. Since most of the studies are carried out in homogeneous reservoirs, more detailed studies of heterogeneities effects in the reservoirs during steam flooding are necessary, since most oil reservoirs are heterogeneous. This paper presents a study of reservoir heterogeneities and their influence in gravity segregation during steam flooding process. In this study some heterogeneous reservoirs with physical characteristics similar those found in the Brazilian Northeast Basin were analyzed. To carry out the simulations, it was used the commercial simulator STARS by CMG (Computer Modeling Group) - version 2007.11. Heterogeneities were modeled with lower permeability layers. Results showed that the presence of low permeability barriers can improve the oil recovery, and reduce the effects of gravity segregation, depending on the location of heterogeneities. The presence of these barriers have also increased the recovered fraction even with the reduction of injected steam rate

Obtenção de álcool alílico (PROP-2-EN-1-OL) a partir da glicerina derivada do biodiesel de óleo de mamona

In this work, biodiesel was produced from castor oil that was a byproduct glycerin. The molar ratio between oil and alcohol, as well as the use of (KOH) catalyst to provide the chemical reaction is based on literature. The best results were obtained using 1 mol of castor oil (260g) to 3 moles of methyl alcohol (138g), using 1.0% KOH as catalyst at a temperature of 260 ° C and shaken at 120 rpm. The oil used was commercially available, the process involves the reaction of transesterification of a vegetable oil with methyl alcohol. The product of this reaction is an ester, biodiesel being the main product and the glycerin by-product which has undergone treatment for use as raw material for the production of allyl alcohol. The great advantage of the use of glycerin to obtain allyl alcohol is that its use eliminates the large amount of waste of the biodiesel and various forms of insult to the environment. The reactions for the formation of allyl alcohol was conducted from formic acid and glycerin in a ratio 1/1, at a temperature of 260oC in a heater blanket, being sprayed by a spiral condenser for a period of 2 hours and the product obtained contains mostly the allylic alcohol .. The monitoring of reactions was performed by UV-Visible Spectrophotometer: FTIR Fourier transform, the analysis showed that these changes occur spectrometer indicating the formation of the product allylic alcohol (prop-2-en-1-ol) in the presence of water, This alcohol was appointed Alcohol GL. The absorption bands confirms that the reaction was observed in (υ C = C) 1470 -1600 cm -1 and (υ CO), 3610-3670 attributed to C = C groups and OH respectively. The thermal analysis was carried out in a thermogravimetric analyzer SDT Q600, where the mass and temperature are displayed against time, that allows checking the approximate rate of heating. The innovative methodology developed in the laboratory (LABTAM, UFRN), was able to treat the glycerine produced by transesterification of castor oil and used as raw material for production of allyl alcohol, with a yield of 80%, of alcohol, the same is of great importance in the manufacture of polymers, pharmaceuticals, organic compounds, herbicides, pesticides and other chemicals

Tornar-se, ser e viver do professorado: entre regularidades e variações identitárias

The main aim of this research has been to analyze the identity patterns of the teacher s staff of fundamental education public schools in the Metropolitan Area of Natal-RN. It sets out from the hypothesis that being a teacher within this context grows out of the regularities of a specific habitus, which, according to Bourdieu, develops into mental schemes of thought and action within a specific social group. This habitus forms the basis on which is built the social representation of being a teacher prevailing in the group, as well as the symbolic differences that typify its identity variations. Three data sources have been fundamental in building up this thesis: (a) formative essays of students graduating from a Higher Teacher s Formation Course, as well as observing some of the public defense of these essays during field work; (b) a questionnaire aimed at classifying economically, socially, and culturally a sample of public teachers of the Natal-RN county; and (c) submitting a sub-sample of this group to the process of Multiple Classification Procedures (MCP). The analysis of data was done according to the multidimensional, non-parametric statistical procedures of both the Category Content Analysis and Enunciation Analysis methods. The results of the analysis took into account an ample set of variables, its associations and implications, the cultural and social profile of the population under scrutiny, their life styles, as well as the strategies they developed in the process of becoming a teacher, and the social representation of being a teacher . We came to the conclusion that the social identity of the teachers corps, or as we prefer to say it being a teacher , is a result of a set of regularities produced by the habitus that gives social shape and meaning to the existence of the group proper. We note the existence of identity variations caused by the variables (a) educational level; and (b) mode of action in fundamental education (if these are the first or last grades where the subjects operate). However, these variations will not break the power of the regularities that give shape, meaning, and social visibility to the group. The social representation of being a teacher points to the tensions, ambiguities, and trends inherent to common sense, as well as to a strong tendency to reassign a new meaning to being a teacher. Our thesis, therefore, is that the identity configuration of the teachers corps under scrutiny is characterized by an integrative synthesis, by-product of a habitus that is superimposed, and at the same time co-exists with different identity variations

Otimização do tempo e temperatura no processamento da gipsita oriunda dos cristalizadores da produção de sal para obter gesso de uso na construção civil

During the process of the salt production, the first the salt crystals formed are disposed of as industrial waste. This waste is formed basically by gypsum, composed of calcium sulfate dihydrate (CaSO4.2H2O), known as carago cru or malacacheta . After be submitted the process of calcination to produce gypsum (CaSO4.0,5H2O), can be made possible its application in cement industry. This work aims to optimize the time and temperature for the process of calcination of the gypsum (carago) for get beta plaster according to the specifications of the norms of civil construction. The experiments involved the chemical and mineralogical characterization of the gypsum (carago) from the crystallizers, and of the plaster that is produced in the salt industry located in Mossoró, through the following techniques: x-ray diffraction (XRD), x-ray fluorescence (FRX), thermogravimetric analysis (TG/DTG) and scanning electron microscopy (SEM) with EDS. For optimization of time and temperature of the process of calcination was used the planning three factorial with levels with response surfaces of compressive mechanical tests and setting time, according norms NBR-13207: Plasters for civil construction and x-ray diffraction of plasters (carago) beta obtained in calcination. The STATISTICA software 7.0 was used for the calculations to relate the experimental data for a statistical model. The process for optimization of calcination of gypsum (carago) occurred in the temperature range from 120° C to 160° C and the time in the range of 90 to 210 minutes in the oven at atmospheric pressure, it was found that with the increase of values of temperature of 160° C and time calcination of 210 minutes to get the results of tests of resistance to compression with values above 10 MPa which conform to the standard required (> 8.40) and that the X-ray diffractograms the predominance of the phase of hemidrato beta, getting a beta plaster of good quality and which is in accordance with the norms in force, giving a by-product of the salt industry employability in civil construction

Avaliação e modelagem da absorção de H2S do gás natural em coluna de leito estagnado

Natural gas, although basically composed by light hydrocarbons, also presents contaminant gases in its composition, such as CO2 (carbon dioxide) and H2S (hydrogen sulfide). The H2S, which commonly occurs in oil and gas exploration and production activities, causes damages in oil and natural gas pipelines. Consequently, the removal of hydrogen sulfide gas will result in an important reduction in operating costs. Also, it is essential to consider the better quality of the oil to be processed in the refinery, thus resulting in benefits in economic, environmental and social areas. All this facts demonstrate the need for the development and improvement in hydrogen sulfide scavengers. Currently, the oil industry uses several processes for hydrogen sulfide removal from natural gas. However, these processes produce amine derivatives which can cause damage in distillation towers, can cause clogging of pipelines by formation of insoluble precipitates, and also produce residues with great environmental impact. Therefore, it is of great importance the obtaining of a stable system, in inorganic or organic reaction media, able to remove hydrogen sulfide without formation of by-products that can affect the quality and cost of natural gas processing, transport, and distribution steps. Seeking the study, evaluation and modeling of mass transfer and kinetics of hydrogen removal, in this study it was used an absorption column packed with Raschig rings, where the natural gas, with H2S as contaminant, passed through an aqueous solution of inorganic compounds as stagnant liquid, being this contaminant gas absorbed by the liquid phase. This absorption column was coupled with a H2S detection system, with interface with a computer. The data and the model equations were solved by the least squares method, modified by Levemberg-Marquardt. In this study, in addition to the water, it were used the following solutions: sodium hydroxide, potassium permanganate, ferric chloride, copper sulfate, zinc chloride, potassium chromate, and manganese sulfate, all at low concentrations (»10 ppm). These solutions were used looking for the evaluation of the interference between absorption physical and chemical parameters, or even to get a better mass transfer coefficient, as in mixing reactors and absorption columns operating in counterflow. In this context, the evaluation of H2S removal arises as a valuable procedure for the treatment of natural gas and destination of process by-products. The study of the obtained absorption curves makes possible to determine the mass transfer predominant stage in the involved processes, the mass transfer volumetric coefficients, and the equilibrium concentrations. It was also performed a kinetic study. The obtained results showed that the H2S removal kinetics is greater for NaOH. Considering that the study was performed at low concentrations of chemical reagents, it was possible to check the effect of secondary reactions in the other chemicals, especially in the case of KMnO4, which shows that your by-product, MnO2, acts in H2S absorption process. In addition, CuSO4 and FeCl3 also demonstrated to have good efficiency in H2S removal

Incorporação do lodo de tanque séptico como matéria-prima de uma mistura asfáltica

In Natal/RN, 68% of the population uses some kind of individual system for their domestic sewers treatment, being that the most used it is septic tank, followed by sumidouro. Every treatment system of sewers, usually used, generates a by-product denominated sludge. That residue presents some components, in its constitution, undesirable under the environmental and sanitary point of view. In such case, to assure that the system treatment has satisfactory results, it is necessary to do the adjusted disposition of the sludge sewage. Several countries are looking for technical alternatives for the use and disposition of residues. Under technical and environmental conditions appropriate, these materials can be used, decreasing the consumption of the natural resources and the treatment need, storage or elimination of the wastes, what decrease the risks created. Some of the alternatives of recycling of the sludge sewage are: the application in the agriculture, in the production of energy and as raw material in the civil construction. This study evaluated asphalt mixtures behavior that partially substituted conventional aggregates by septic tank sludge. The septic tank sludge gave origin to two raw materials called raw sludge and sludge ash. The raw sludge was put as a small aggregate and the sludge ash as filler. In the first experiment it was made a comparison between the mixture with conventional aggregates and the mixtures that replaced sand by raw sludge in the proportions from 5% to 40%. In the second experiment, it was made comparison between mixtures with 1%, 2% and 3% of sludge ash and cement. The stages developed along the study were: physical characterization of the conventional materials; physical, chemistry, thermal, mineralogical characterizations and analysis of environmental risk of the raw sludge; physical characterization and analysis of environmental risk of the sludge ash; analysis of the mixtures performance through its volumetric and mechanical characteristics; forecast of the mixtures susceptibility in the moisture presence. For the grain size composition used and with the percentage asphalt adopted, the mixtures with up to 7,5% of raw sludge in his composition attend to the National Department of Transports Infrastructure (DNIT) specifications. However, in agreement with the mixtures susceptibility in the moisture presence, the mixtures with addition of raw sludge don't present satisfactory acting. In such case, they could be used in arid and semi-arid areas. The raw sludge application in mixtures increased their voids volume and their stability. However, it damaged mixtures adhesiveness. Mixtures with sludge ash and with cement presented similar behavior. However, mixtures with sludge ash presented a better performance than mixtures with cement as for their stability and their tensile strength ratio. The mixture with 1% of sludge ash is better. The wastes studied don't represent environmental risk

Consumo e digestibilidade aparente de dietas com níveis crescentes do subproduto do caju em ovinos

The present study was conducted to evaluate the intake and digestibility of diets containing increasing levels of byproduct of cashew in sheep. The animals were distributed in a completely randomized design were evaluated in four levels (0%, 20%, 40%, 60%) by product of cashew with four replicates, making up 16 observations. The indicator used was the Purified Lignin and Enriched - LIPE ®. The scorer was orally administered directly into the mouth of the animals, in the form of capsules 250mg/animal/dia for a period of two days and five days of adaptation samples being the same supplied with the aid of a hose polyethylene and a device allowing the release of the capsule in the esophagus of sheep. With the estimate made by the indicator LIPE was observed a reduction for DM, OM, CP, NDF, EE, NFC and MM along the inclusion of byproduct of cashew. The results of nutrient digestibility were not satisfactory with the inclusion of byproduct of cashew, reducing linearly with the inclusion of the diets. The use of increasing levels of byproduct of cashew in the diets of sheep did not provide satisfactory results, it is not feasible to use the animals studied in this experiment

O papel das relações sociais e da atenção social durante tarefas cooperativas em Callithrix jacchus

Several studies on nonhuman primates show that the relationships between individuals strongly influence the expression of cooperative behavior, both in natural environment and in captivity settings. Recent studies suggest that cooperative breeders present outstanding performance in tasks involving social cognition, such as cooperative tasks with experimental apparatuses. In experimental research on this subject it is crucial to differentiate between real cooperation (or communicative cooperation, mediated by social attention) and by-product cooperation that results from simultaneous actions of individuals. The present study assessed, in Callithrix jacchus, a cooperative breeder species, if social relationships and social attention between subjects are important factors during performance in cooperative tasks. During the experimental procedure the animals participated in three different cooperative tasks: cooperation task, prosocial task and control task. Diverging from the literature, matrix correlation tests revealed no significant relationship between grooming or proximity and the execution of the tasks, suggesting that other factors such as age or hierarchy may have an effect on the performance in cooperative tasks in this species. There was also no relationship between the execution of the cooperative tasks and social glances, suggesting that there was no social attention during the tasks. Moreover, there were lower rates of social glances in the cooperative tasks as opposed to the control tasks. However, the small number of pulls in prosocial tasks suggests that the animals distinguished between tasks that benefited only a partner and tasks that generated benefits to themselves, choosing the latter. We conclude that, for the tasks presented in this study, we could neither detect the role of social relationships on the cooperative tasks nor assert that there were true cooperation and prosocial behavior

Incrustação em poço produtor de petróleo e gás natural: um estudo de caso

Water and gas is a common by - product of the oil production process. Production may be compromised by the precipitation of inorganic salts in both the reservoir and producing well, through scale formation. This precipitation is likely the cause of the formation damage. High temperatures and h igh pressures (HTHP) may favor the precipitation of insoluble salts. The most common types of scale in oil fields are calcium carbonate and calcium sulphate, strontium and barium sulphate. New types of scale formation have attracted special attention such as zinc sulphide and lead. This precipitation may occur in the pores of reservoir rocks, in the production string and in equipment, causing obstructions and consequent production losses. In this study, the influence of well depth on incrustation compositio n was investigated to design removal treatments and assess the behavior of these deposits along the string, through the analysis of pressure and temperature. Scale residues were recovered from the inside of the production string of an oil and gas well duri ng the string removal operation. A total of 10 samples from different depths (15.4 m to 4061.5 m) were obtained. Initially a dissolution test was conducted in weak acid, similar to that used in removal operations with this type of scale formation. Majority composition was defined and confirmed by dissolution tests using X - Ray Fluorescence Spectroscopy (XRF), X - Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) techniques. Residues with distinct characteristics were observed in different proportion s, showing a tendency toward increased and/or decreased mass with depth. In the samples closest to the surface, typical sandstone residues were found, with calcium (45% Ca) as the metal of highest concentration. The obtained results indicate correlations o f the scale types studied with the depth and, consequently, with the thermodynamic conditions of pressure and temperature.

Degradação fotocatalítica oxidativa do fenol utilizando carvão obtido da pirólise de diferentes biomassas

The modern industrial progress has been contaminating water with phenolic compounds. These are toxic and carcinogenic substances and it is essential to reduce its concentration in water to a tolerable one, determined by CONAMA, in order to protect the living organisms. In this context, this work focuses on the treatment and characterization of catalysts derived from the bio-coal, by-product of biomass pyrolysis (avelós and wood dust) as well as its evaluation in the phenol photocatalytic degradation reaction. Assays were carried out in a slurry bed reactor, which enables instantaneous measurements of temperature, pH and dissolved oxygen. The experiments were performed in the following operating conditions: temperature of 50 °C, oxygen flow equals to 410 mL min-1 , volume of reagent solution equals to 3.2 L, 400 W UV lamp, at 1 atm pressure, with a 2 hours run. The parameters evaluated were the pH (3.0, 6.9 and 10.7), initial concentration of commercial phenol (250, 500 and 1000 ppm), catalyst concentration (0, 1, 2, and 3 g L-1 ), nature of the catalyst (activated avelós carbon washed with dichloromethane, CAADCM, and CMADCM, activated dust wood carbon washed with dichloromethane). The results of XRF, XRD and BET confirmed the presence of iron and potassium in satisfactory amounts to the CAADCM catalyst and on a reduced amount to CMADCM catalyst, and also the surface area increase of the materials after a chemical and physical activation. The phenol degradation curves indicate that pH has a significant effect on the phenol conversion, showing better results for lowers pH. The optimum concentration of catalyst is observed equals to 1 g L-1 , and the increase of the initial phenol concentration exerts a negative influence in the reaction execution. It was also observed positive effect of the presence of iron and potassium in the catalyst structure: betters conversions were observed for tests conducted with the catalyst CAADCM compared to CMADCM catalyst under the same conditions. The higher conversion was achieved for the test carried out at acid pH (3.0) with an initial concentration of phenol at 250 ppm catalyst in the presence of CAADCM at 1 g L-1 . The liquid samples taken every 15 minutes were analyzed by liquid chromatography identifying and quantifying hydroquinone, p-benzoquinone, catechol and maleic acid. Finally, a reaction mechanism is proposed, cogitating the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. Applying the model of Langmuir-Hinshelwood along with a mass balance it was obtained a system of differential equations that were solved using the Runge-Kutta 4th order method associated with a optimization routine called SWARM (particle swarm) aiming to minimize the least square objective function for obtaining the kinetic and adsorption parameters. Related to the kinetic rate constant, it was obtained a magnitude of 10-3 for the phenol degradation, 10-4 to 10-2 for forming the acids, 10-6 to 10-9 for the mineralization of quinones (hydroquinone, p-benzoquinone and catechol), 10-3 to 10-2 for the mineralization of acids.

Qual é a sua tribo? O uso do TAI online no desvelamento de conhecimentos sociais ocultos

The Implicit Association Test (IAT) has succeeded in accessing mental phenomena hardly exposed through self-report and explicit measures well known in the traditional studies on psychology. Although this measurement technique is among the most consistent in international publications, the few articles in Brazil have not deepened on theoretical issues that underlie the practice. This created a gap between the spread of this measure in the country and the production seen in international laboratories, both at quantitative and qualitative terms. In this context, the online labs implemented in several countries, including Brazil, created unique opportunities to overcome these disparities. Our work sought theoretical and conceptual clarification, contextualized to the historical development of the IAT and its online version, displaying affordably an unprecedented presentation of the virtual tool adapted to the Brazilian public. In a second step, we investigated empirically the data obtained by the Brazilian electronic portal "Countries", analyzing the degree of implicit and explicit nationalism of 2271 Brazilian subjects collected from early 2009 to late 2014. Our goal was to determine whether the data results obtained in a time of major sporting confrontation (FIFA World Cup 2010 and 2014) differ from periods when the tournament did not happen. Analyzes showed differences on the eve of the sporting confrontation, when the increase in the implicit nationalism was clearly superior, even with no effect by self-reports. In an independent analysis of a cultural context, there is an oscillation of explicit nationalism over the years, but not for the implicit action. In addition, it was found in women greater degree of implicit and explicit nationalism than in men, with both sexes presenting their preferences towards Brazil. In an end section, we suggest that nationalism may be a by-product of universal mental mechanisms that evolved to identify of the belonging group categorization, corroborating with the group favoritism. We propose that the intensification of the group preference on the eve of the competition has as its ancestral function strengthen the cohesion of the group in preparation to confrontational situations. We pointed out the need for studies on the differences between the sexes in matters relating to group membership belonging. It was expected largest nationalist attitudes in men reflecting the maintenance of cohesive groups in ancient societies. Thus, it appears a singular importance impart the traditional TAI studies with its online version for future investigations of human behavior in various areas of knowledge.

Qual é a sua tribo? O uso do TAI online no desvelamento de conhecimentos sociais ocultos

The Implicit Association Test (IAT) has succeeded in accessing mental phenomena hardly exposed through self-report and explicit measures well known in the traditional studies on psychology. Although this measurement technique is among the most consistent in international publications, the few articles in Brazil have not deepened on theoretical issues that underlie the practice. This created a gap between the spread of this measure in the country and the production seen in international laboratories, both at quantitative and qualitative terms. In this context, the online labs implemented in several countries, including Brazil, created unique opportunities to overcome these disparities. Our work sought theoretical and conceptual clarification, contextualized to the historical development of the IAT and its online version, displaying affordably an unprecedented presentation of the virtual tool adapted to the Brazilian public. In a second step, we investigated empirically the data obtained by the Brazilian electronic portal "Countries", analyzing the degree of implicit and explicit nationalism of 2271 Brazilian subjects collected from early 2009 to late 2014. Our goal was to determine whether the data results obtained in a time of major sporting confrontation (FIFA World Cup 2010 and 2014) differ from periods when the tournament did not happen. Analyzes showed differences on the eve of the sporting confrontation, when the increase in the implicit nationalism was clearly superior, even with no effect by self-reports. In an independent analysis of a cultural context, there is an oscillation of explicit nationalism over the years, but not for the implicit action. In addition, it was found in women greater degree of implicit and explicit nationalism than in men, with both sexes presenting their preferences towards Brazil. In an end section, we suggest that nationalism may be a by-product of universal mental mechanisms that evolved to identify of the belonging group categorization, corroborating with the group favoritism. We propose that the intensification of the group preference on the eve of the competition has as its ancestral function strengthen the cohesion of the group in preparation to confrontational situations. We pointed out the need for studies on the differences between the sexes in matters relating to group membership belonging. It was expected largest nationalist attitudes in men reflecting the maintenance of cohesive groups in ancient societies. Thus, it appears a singular importance impart the traditional TAI studies with its online version for future investigations of human behavior in various areas of knowledge.