Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial

In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate heat. A pressure of 2.5mbar and temperatures of 400 and 300ºC com treatment time of two and three hours were used to evaluate its performance as cutting tool (punch) of bicycle backs. Hardness, micro-structural aspects (layer thickness, interface, grain size etc), and crystal phases on the surface were appraised. When treated to tension relief, thermally treated to maximum heat temperature, temperature and temperate heat, the samples presented hardness levels of 243HV, 231HV, 832HV, and 653HV, respectively. The best nitrification conditions were: four hours and 300ºC for heat samples. A superficial hardness of 1000HV and a 108µm thickness for the nitrided layer were found in these samples

Efeitos do alongamento e do aquecimento no desempenho isocinético e na atividade eletromiográfica do músculo bíceps femoral ensaio clínico randomizado

To evaluate the effects of warm-up and stretching, singly or combined, on isokinetic performance and electromyographic activity of the biceps femoris. Materials and methods: Sixty-four volunteers of both sexes, with mean age of 23,1 ± 3,5 years and mean body mass index of 23,5 ± 2,5 Kg/m2 were randomly assigned into 4 groups: control, warm-up (stationary bicycle for 10 minutes), stretching (4 sets of 30 seconds of hamstring muscles static stretching) and warm-up + stretching. All the volunteers were submitted to evaluation pre and post-intervention of the muscle latency time and biceps femoris RMS and the passive torque, peak torque and power of the hamstring muscles. Results: The warm-up + stretching group had reduction of muscle latency time. There was a reduction of RMS during passive torque evaluation in stretching group. The RMS during isometric evaluation was reduced in all experimental groups. The RMS during eccentric evaluation showed reduction in control and warm-up + stretching groups. The passive torque and the eccentric peak torque had no significant differences pre to post-intervention in any group. There was reduction in isometric peak torque in all groups. Conclusion: The warm-up and stretching, when applied in combination can reduce the muscle latency time; stretching protocol promoted neural changes; the protocols used did not alter the muscle viscoelastic properties

Efeitos da respiração em freno-labial sobre os volumes pulmonares e o padrão de hiperinsuflação dinâmica em pacientes com asma

Objectives: To evaluate how to develop dynamic hyperinflation (DH) during exercise, the influence of pursed-lip breathing in (PLB) on breathing pattern and operating volume in patients with asthma. Methods: We studied 12 asthmatic patients in three moments: (1) anthropometry and spirometry, (2) submaximal incremental cycle ergometer test in spontaneous breathing and (3), submaximal incremental test on a cycle ergometer with PLB using the Opto-electronic plethysmography. Results: Evaluating the end-expiratory lung volume (EEV) during submaximal incremental test in spontaneous breathing, patients were divided into euvolume and hyperinflated. The RFL has increased significantly, the variation of the EEV group euvolume (1.4L) and decreased in group hyperinflated (0.272L). In group volume observed a significant increase of 140% in Vt at baseline, before exercise, comparing the RFL and spontaneous breathing. Hyperinflated group was observed that the RFL induced significant increases of Vt at all times of the test incremental baseline, 50%, 100% load and 66% recovery, 250%, 61.5% and 66% respectively. Respiratory rate decreased significantly with PLB at all times of the submaximal incremental test in the group euvolume. The speed of shortening of inspiratory muscles (VtRcp/Ti) in the hyperinflated increased from 1.6 ± 0.8L/s vs. 2.55 ± 0.9L/s, whereas in the RFL euvolume group ranged from 0.72 ± 0.31L/s vs. 0.65 ± 0.2L/s. The velocity of shortening of the expiratory muscles (VtAb/Te) showed similarity in response to RFL. In group hyperinflated varied vs. 0.89 ± 0.47 vs. 0.80 ± 0.36 and ± 1.17 ± 1L vs. 0.78 ± 0.6 for group euvolume. Conclusion: Different behavior in relation to EEV in patients with moderate asthma were observed, the HD and decreased EEV in response to exercise. The breathing pattern was modulated by both RFL performance as at home, making it more efficient

Avaliação do desempenho do aço D6 tratado termicamente e netretado em plasma com gaiola catódica visando aplicação industrial

In this research there was an evaluation of the best conditions of nitriding in plasma within a cathodic cage at an atmosphere of 80% N2-20%H2 in samples of tool manganese steel AISI D6, cold working, treated thermally in the following conditions: tension relief, treated thermally to temperature of maximum heat, temperate heat and temperate and temperate heat. A pressure of 2.5mbar and temperatures of 400 and 300ºC com treatment time of two and three hours were used to evaluate its performance as cutting tool (punch) of bicycle backs. Hardness, micro-structural aspects (layer thickness, interface, grain size etc), and crystal phases on the surface were appraised. When treated to tension relief, thermally treated to maximum heat temperature, temperature and temperate heat, the samples presented hardness levels of 243HV, 231HV, 832HV, and 653HV, respectively. The best nitrification conditions were: four hours and 300ºC for heat samples. A superficial hardness of 1000HV and a 108µm thickness for the nitrided layer were found in these samples