Desenvolvimento e avaliação de padrão de torque para calibração de torquímetros em três faixas de medição

The continuous development of instruments and equipment used as tools or torque measurement in the industry is demanding more accurate techniques in the use of this kind instrumentation, including development of metrological characteristics in torque measurement. The same happens with the needs in calibration services. There is a diversity of methods of hand torque tools in the market with different measuring range but without complaining with technical standards in terms of requirements of quality and reliability. However, actually there is no choice of a torque measuring standard that fulfils, with low cost, the needs for the calibration of hand torque tools in a large number of ranges. The objective of this thesis is to show the development and evaluation of a torque measuring standard device with a conception to allow the calibration of hand torque tools with three levels of torque with an single instrument, promoting reduction of costs and time in the calibration, also offering reliability for the evaluation of torque measuring instrument. To attend the demand in the calibration of hand torque tools it is necessary that the calibration laboratories have a big collection of torque measuring standards, to fulfills the needs of the costumer, what is very costly. The development of this type of torque measuring standard revealed a viable technique and economically making possible the calibration of hand torque tools in different nominal ranges through a single measurement system versatile, efficient and of easy operation

Correlação entre torque, equlíbrio e função do joelho após reconstrução do LCA

Background: Several studies emphasize the importance of assessing the knee function after anterior cruciate ligament (ACL) reconstruction. The influence of several variables on the function of these patients has been analyzed, but there is no consensus in the science literature. Purpose: To evaluate the correlation between the torque and balance on the knee function after ACL reconstruction. Methods: 23 males patients with ACL reconstruction were tested. The procedures of the study included analysis of concentric peak torque at 60o/s and 180o/s of quadriceps femoris and hamstring muscle with a isokinetic dynamometer. The balance in single-limb stance was measured with stabilometry. The functional performance were performed by two hop tests. To estimate the subjective function of the patients was applied Lysholm Knee Scoring Scale and a Global Rating scale. Results: The analysis of data showed a moderate positive correlation between knee extensor torque and functional performance tests (r= 0,48; p=0,02). A moderate negative correlation was found between the two variables of the stabilometry center of pressure and average speed of centre of pressure and the Global Rating scale (r = -0.4, p = 0,04 and r = -0,49, p = 0 ,02, respectively). No correlation was found between peak torque and balance in single-limb stance. Conclusion: The results of the present study suggest that knee extensor strength and postural balance have some influence on knee function in patients after ACL reconstruction

Efeito de três tecnicas de alongamento muscular sobre o torque e atividade eletromiográfica

PURPOSE: To examine the acute effects caused by three techniques for stretching the hamstrings muscle on the active concentric peak torque (PT), passive PT and electromyographic activity (EMG). METHODS: Sixty volunteers (mean ± SD age, 22.6 ± 3 years), height 1.64 ± 0.07m and body weight of 58 ± 8.6kg, were randomly allocated into 4 groups of 15 subjects: Control Group (CG) - 5 minutes at rest, Static Stretching Group (SG) - 2 x 30s; Hold-Relax Group (HRG) - 3 x 6s of isometric contraction of hamstrings interspersed by 10s of hamstrings stretching and agonist Hold-Relax Group (AHRG) - 3 x 6s of isometric contraction of the quadriceps interspersed by 10s of hamstrings stretching. Evaluation has been conducted preand post-intervention, which verified the active concentric PT, passive PT EMG activity of IT. The statistical inference was performed by testing intra and inter, significance level at 5%. RESULTS: After intervention, there was a reduction in passive PT on CG, accompanied by a reduction of EMG activity, and an increase in passive PT on SG and AHRG. There was no change in the active concentric PT, or change in EMG activity. CG showed an increase in angle of the PT active, while the other groups showed no change. CONCLUSION: The results suggest that the shortterm stretching: 1) causes acute increase in passive torque, since the muscle does not perform sub-maximal contraction, 2) does not change in electromyographic activity and active torque, ind ependent of the technique

Development of an active orthosis prototype for lower limbs

ARAUJO, Márcio V. ; ALSINA, Pablo J. ; MEDEIROS, Adelardo A. D. ; PEREIRA, Jonathan P.P. ; DOMINGOS, Elber C. ; ARAÚJO, Fábio M.U. ; SILVA, Jáder S. . Development of an Active Orthosis Prototype for Lower Limbs. In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING, 20., 2009, Gramado, RS. Proceedings… Gramado, RS: [s. n.], 2009

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET

Efeito da adição dos azocorantes DR73 e DB79 nas propriedades do poli(metacrilato de metila)

Currently new polymeric materials have been developed to replace other of traditionally materials classes. The use of dyes allows to expand and to diversify the applications in the polymeric materials development. In this work the behavior and ability of azo dyes Disperse Blue 79 (DB79) and Disperse Red 73 (DR73) on poly(methyl methacrylate) (PMMA) were studied. Two types of mixtures were used in the production of masterbatches: 1) rheometer 2) solution. Processing by extrusion-blow molding of PMMA was carried out in order to evaluate the applications of polymeric films. Thermal analysis were performed by thermogravimetry to evaluate polymer and azo dyes thermal stability. Colorimetric analysis were obtained through monitoring the spectral variations associated with sys/trans/anti azo dyes isomerization process Colorimetric data were treated and evaluated in accordance to the color system RGB and CIEL*ab, by monitoring the color change as function of time. Mechanical properties, characterized by tensile tests, were evaluated and correlated with the presence and content of azo dyes in the samples. Analyses by scanning electronic microscopy (SEM) were performed on the surfaces of samples to check the azo dye dispersion after the mixing process. It was concluded that the production of PMMA/azo dyes is possible and feasible, and the mixtures produced had synergy of properties for use in various applications

O efeito do tratamento da atapulgita no desenvolvimento de compósito com o polietileno reciclado

The study aimed at the treatment of attapulgite for the development and characterization of composite recycled low density polyethylene - PEBD_rec embedded with natural attapulgite - ATP_NAT, sifted - ATP_PN and attapulgite treated with sulfuric acid - ATP_TR in different compositions (1, 3 and 5%) and compared with the PEBD_rec. The atapulgitas, natural, screened and treated, were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and determining the area specific surface (BET). The composites were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), Xray diffraction (XRD), torque rheometry, scanning electron microscopy (SEM) and traction. The composite PEBD_rec / ATP (natural, sieved and treated) were produced by mixing in the molten state in a single screw extruder matrix wire with subsequent reprocessing matrix tape. It was found that the screening of attapulgite not reduce the quantity of quartz and the acid treatment completely extracted dolomite aggregate impurities of the channels attapulgite, and increase their surface area. The addition of attapulgite in PEBD_rec acts as a catalyst, reducing the thermal stability of the polymer. The increased concentration of attapulgite, increases resistance and reduces the elongation at break and modulus of elasticity of the composite PEBD_rec / attapulgite

Processamento e caracterização de compósitos Poli(METACRILATO DE METILA)/Sílica (PMMA/SiO2)

Currently the search for new materials with properties suitable for specific applications has increased the number of researches that aim to address market needs. The poly (methyl methacrylate) (PMMA) is one of the most important polymers of the family of polyacrylates and polymethacrylates, especially for its unique optical properties and weathering resistance, and exceptional hardness and gloss. The development of polymer composites by the addition of inorganic fillers to the PMMA matrix increases the potential use of this polymer in various fields of application. The most commonly used inorganic fillers are particles of silica (SiO2), modified clays, graphite and carbon nanotubes. The main objective of this work is the development of PMMA/SiO2 composites at different concentrations of SiO2, for new applications as engineering plastics. The composites were produced by extrusion of tubular film, and obtained via solution for application to commercial PMMA plates, and also by injection molding, for improved the abrasion and scratch resistance of PMMA without compromising transparency. The effects of the addition of silica particles in the polymer matrix properties were evaluated by the maximum tensile strength, hardness, abrasion and scratch resistance, in addition to preliminary characterization by torque rheometry and melt flow rate. The results indicated that it is possible to use silica particles in a PMMA matrix, and a higher silica concentration produced an increase of the abrasion and scratch resistance, hardness, and reduced tensile strength

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Efeito da adição do poli(etileno acrilato de metila) (ema) e da fibra de linter de algodão nas propriedades do poli(tereftalato de etileno) reciclado (petrec)

The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA

Desenvolvimento de bioblendas poliméricas a partir de gelatina bovina e de tilápia com amido de milho

The natural raw materials acquired special importance beside the mineral raw materials with the need for using alternative sources to oil, because they can be used to produce biopolymers. Gelatin, produced from the denaturation of collagen, and starch, an abundant polysaccharide in various plants, are examples of biopolymers which have several technological applications, especially in films. The objective of this work is to produce polymeric bioblends with gelatin and corn starch using two types of gelatin: commercial bovine gelatin and gelatin produced from mechanically separated flesh of tilapia (Oreochromis niloticus). For the extraction of tilapia gelatin 3 distinct pretreatments, followed by extraction in distilled water under heating were performed. The properties of gelatin extracted were similar to bovine gelatin, and the differences can be explained by the difference in extraction processes and sources. Blends of commercial gelatin and starch were produced in an internal mixer from a Haake torque rheometer, to study the behavior of the gelatin mixture with starch, thus, the same compositions were processed by twin screw extrusion, to define the mixing parameters. Subsequently, the extrusion of blends of tilapia gelatin and corn starch was carried out in the same twin screw extruder. The physico-chemical, rheological and morphological properties of the blends with thermoplastic starch and gelatin were studied. It was found that various properties vary linearly with increasing concentration of the components. The blends produced are immiscible, and among the two gelatins, tilapia gelatin showed a better interfacial adhesion with the corn starch. Regarding the morphology, gelatins formed the dispersed phase in all compositions studied, even in compositions rich in starch. Can be concluded that the procedure for tilapia gelatin extraction is feasible and advantageous, and the increasing in its scale to a reactor of 30 liters is possible, with a satisfactory yield. The bioblends of bovine gelatin/corn starch and tilapia gelatin/corn starch were successfully produced, and the processing conditions were appropriate

Prevalência de oclusopatias e caracteríticas cefalométricas e dentais de escolares cearense da cidade de Fortaleza

The people of Ceará state are descended from miscegenation between the Portuguese colonizers and the native population, resulting in a different facial pattern from other populations. It is important that this pattern be thoroughly understood, along with its minimum and maximum values so that they can be assessed and respected, allowing professionals who deal with the craniofacial complex to work more efficiently and scientifically. Aim: To characterize the morphological pattern of individuals from Ceará state, whose father and grandfather are also native from Ceará, in the 10-12 year age group, not submitted to previous orthodontic treatment, in order to determine: 1) the prevalence of occlusal pattern; 2) the prevalence of dental anomalies (DA) and, 3) the skeletal and dental cephalometric characteristics of individuals that present with normal occlusion and harmonious facial pattern. Methodology: A list of 10-12 year-olds was obtained from 515 schools containing 162,713 students (Education Secretariat of Ceará State), from which 234 individuals were examined (107 boys and 157 girls). The assessment criteria adopted were: 1) Angle s Classification System to determine occlusal pattern. The occlusal characteristics were measured through overbite, overjet, crowding and interincisal diastema. 2) DA are anomalies of number, shape, size, eruption and structure and, 3) in the group that presented with normal occlusion, we used cephalometric analysis measures proposed by Downs, Steiner, Tweed, Holdaway, Jacobson and McNamara. Results: 1) 25.8% of the schoolchildren had normal occlusion, 47.5% class I malocclusion, 22.3% class II malocclusion and 4.2% class III malocclusion. No statistically significant difference was found between the age group studied and sex. Thirty percent of the individuals had normal overbite, while 36.7% and 19.7% had increased and reduced overbite, respectively. Normal overjet was found in 33.7% of the individuals, increased overjet in 50% and reduced in 16.3%. Dental crowding was observed in 62.5% of the individuals and the presence of interincisal diastema in 14.8%. 2) The prevalence of DA was 56.1%, 6.8% in the number, 10.8% in shape, 4.1% in size, 34.5% in eruption, 26.4% in structure and 17.4% had more than one DA. No association was found between DA and sex, but DA was significantly associated to malocclusion (p<0.05); 3) there was no association between sex or facial type between the measures of nasal-labial angle, position and effective maxillary length, effective mandibular length and the sagittal relationship between the molars, overjet and overbite, position of upper incisors, lower incisors and between the incisors themselves. There was a difference between sex, on the VERT index and in lower anterior facial height, upper incisor inclination and line-H, between facial types for the occlusal plane angles, mandibular plane, facial axis, lower incisor inclination, mandibular position, upper incisor position, lower anterior facial height, ANB and line-H. It was concluded that: 1) the most prevalent occlusal type was class I malocclusion, with no distinction for sex or age group, and the assessment of occlusal characteristics showed that excessive overbite and overjet were the most predominant findings, along with a high occurrence of tooth crowding; 2) a high prevalence of DA was found, particularly eruption anomalies, not influenced by sex but significantly associated to malocclusion and 3) individuals from Ceará are predominantly brachyfacial, exhibiting a number of similarities inherent to their facial pattern, such as a convex profile, retracted jaw, reduced lower third and protruded lower incisors. This study was multidisciplinary, involving researchers from the areas of epidemiology, radiology and dentistry, thereby meeting the multidisciplinarity requirements of the Postgraduate Program in Health Sciences

Determinação da idade dental de crianças brasileiras nordestinas: novos valores de conversão de maturidade dental para população específica

Since Demirjian's system of estimating dental maturity was first described, many researchers from different countries have tested its accuracy among diverse populations. Some of these studies have pointed out a need to determine population-specific standards. In Brazil, the Northeast region is the one that most suffers the negative impact of exodus, specially related to the increase of abandoned children in the cities. The aim of this study was to test the accuracy of Demirjian's system for assessing the dental maturity of northeastern Brazilian children, so as to present a scale for maturity score conversion into dental age developed specifically for this population. This could be used for forensic, anthropological and legal matters, and also as a model for other countries attempting to formulate their own conversion scales. Panoramic radiographs of 1,491 children (821 females and 670 males), aged 7 to 13 years, from Ceará state, northeast Brazil, were assessed by a single observer to determine dental age (DA) according to Demirjian's system. The mean percentage of intra-observer agreement was 86.6%, with a mean Cohen's Kappa coefficient of 0.67 (substantial agreement). The DA was compared by paired t-test to subjects' chronological age (CA). The differences between CA and DA in all age groups were statistically significant (p<0.0001), demonstrating a great advancement in DA among Brazilians. Scatter plots were drawn for both genders, and the data were fitted to a growth curve, y = 100/ (1 + e-a(x b)). Graphs corresponding to the 50th percentile curves were produced. A table with new values for the conversion of maturity score into dental age for northeastern Brazilian children is presented. The great advancement in DA, as obtained by Demirjian's system in this population, justified the determination of specific scores for dental maturity assessment

Efetividade do uso tópico de fluoreto e da escovação no controle de cáries produzidas "in vivo"

The objective of this clinical study was to evaluate the effectiveness of the toothbrushing with and without fluoride and the daily fluoride rinse (NaF 0.05%) on produced white spot, in vivo. This was a clinical study, controlled, randomized and triple blind. Thirty patients were selected for orthodontics reasons from Orthodontics Specialization Course at the Brazilian Dental Association - Section of Rio Grande do Norte. In this study it was used 4 bicuspid upper and lower. They had orthodontic reason for extractions, in 35 days, at least. The sample had one hundred and twenty teeth that received orthodontic bands. The bands were fixed with polycarboxylate cement, and there was a space standardized between bands and one surface of teeth. The four bicuspid of each patients were randomized and nominated as A, B, C and D. These nominations determinated the sequence of the extractions and what was done in each tooth. All the patients had been submitted to the toothbrushing with or without fluoride for 35 days. After this period, the A tooth of each patient was extracted to serve as control. The others teeth (B, C and D) were extracted one by each week. The entire sample was analyzed through the clinical examination and by laser fluorescence (DIAGNOdent®) in three different times: before orthodontic bands, 28 days after fixed and then removed the bands and, the last one, 07 days after one of the three treatments (toothbrushing with or without fluoride, tooth paste with fluoride and mouth rinse with fluoride). At the beginning all groups (A, B, C and D) had the same conditions, no significant difference was found. The same situation was found in a clinical examination. The results of the DIAGNOdent® for the groups that used tooth paste without fluoride, with fluoride and mouth rinse with fluoride, after 28 days, there was no significant difference. Clinically, the white spot was formed in all teeth after 28 days. When it was compared the three treated groups, the group without fluoride in tooth paste had worst result than the others groups. But there was no significant association between the number of active and inactive white spots and the type of treatment that the teeth had received. The demineralization of the enamel surface, under the orthodontic bands, it happened in a few weeks. The exposition of the white spots in oral environmental resulted in an improvement, but it was not enough to return to the values from the base line, either for the toothbrushing and/or the use of fluorite mouth rinse. Mouth rinse and toothpaste with fluoride have showed to reduce the incidence of demineralization in the enamel, but none seems to be superior to another one in an in vivo study

O tratamento ortodôntico em uma perspectiva a longo prazo: avaliação da estabilidade oclusal e do grau de satisfação dos pacientes

This study aimed to evaluate factors associated to orthodontic treatment stability and patient satisfaction in the long-term. A total of 209 patients (88 class I and 121 class II) treated with straight wire fixed appliance were selected at least 5 years post treatment. Six hundred twenty seven dental casts were examined with the PAR Index at pretreatment (T1), end of treatment (T2), and at long-term follow up (T3, mean 8.5 years post treatment). At T3, a Dental Impact on Daily Living questionnaire was used to assess patient satisfaction with the dentition in the long-term. Friedman test and multiple regression analysis were used to evaluate changes among the time points and factors associated with stability and patient satisfaction. Predictive factors used to exam the occlusion were: PAR Index at T1 and T2, age at T1, the amount of time without retainer, length of Hawley retainer wear, length of follow-up, sex, extraction and third molar status. To assess patient satisfaction were considered: changes produced by the orthodontic treatment (PAR T2-T1), post treatment stability (PAR T3), age at the start of treatment (T1), length of treatment (T2-T1), gender, and extraction. Orthodontic treatment produced a significant improvement of 94.2% in the PAR Index (T2-T1), but this change was not associated with the level of satisfaction when the patient was questioned at T3. No significant change was observed between T2 and T3. However, when the sample was divided according to the level of finalization (PAR T2), it was observed that well-finished patients experienced some deterioration (P<.001), whereas the less well-finished ones showed some improvement (P<.05). Even with the deterioration, the well-finished patients still had a better PAR Index at T3 compared to the less well-finished ones (PAR T2- T3). Regression analysis showed that PAR Index at T1 and T2, age at T1, and length of retainer wear had a slight association with occlusal stability (R2 = 0.27). Patient satisfaction was significantly associated only with PAR Index at T3 (r2=0.125, P<.0001). We can conclude that, even thought orthodontic treatment is quite stable, not so well-finished treatments tend to show some improvement and well-finished ones deteriorate some in the long-term. Despite of that, well-finished patients still have better occlusal characteristics. Patient satisfaction is not related to the result of orthodontic treatment; nevertheless, there is a slight association with dentition in the long-term