Uma fonte chaveada de 50kW com correção de fator de potência para alimentação de uma tocha de plasma Indutiva utilizando técnicas de controle digital

This work deals with the development of an experimental study on a power supply of high frequency that provides the toch plasmica to be implemented in PLASPETRO project, which consists of two static converters developed by using Insulated Gate Bipolar Transistor (IGBT). The drivers used to control these keys are triggered by Digital Signal Processor (DSP) through optical fibers to reduce problems with electromagnetic interference (EMI). The first stage consists of a pre-regulator in the form of an AC to DC converter with three-phase boost power factor correction which is the main theme of this work, while the second is the source of high frequency itself. A series-resonant inverter consists of four (4) cell inverters operating in a frequency around 115 kHz each one in soft switching mode, alternating itself to supply the load (plasma torch) an alternating current with a frequency of 450 kHz. The first stage has the function of providing the series-resonant inverter a DC voltage, with the value controlled from the power supply provided by the electrical system of the utility, and correct the power factor of the system as a whole. This level of DC bus voltage at the output of the first stage will be used to control the power transferred by the inverter to the load, and it may vary from 550 VDC to a maximum of 800 VDC. To control the voltage level of DC bus driver used a proportional integral (PI) controller and to achieve the unity power factor it was used two other proportional integral currents controllers. Computational simulations were performed to assist in sizing and forecasting performance. All the control and communications needed to stage supervisory were implemented on a DSP

Contribuições para a detecção e identificação de faltas em inversores Multiníveis

This work presents contributions in the detection and identication of faults in multilevel inverters through the study of the converters behavior under these operation conditions. Basically, the approached fault consists of an open-circuit in any switch of a three-level clamped diode inverter. The converter operation is characterized in the pre and post-fault states. A wave form behavior analysis of the pole voltage, phase current and dc-bus current is also done, which highlights characteristics that allow the detection of failure and, even, under favorable conditions, the identication of the faulty device. A compensation strategy of the approached fault (open-switch) is also investigated with the purpose of maintaining the driving system operational when a failure occurs. The proposed topology uses SCRs in parallel with the internal switches of the inverter, which allows, in some occasions, the full utilization of the dc-bus

Desempenho de um painel fotovoltaico de baixa tensão, acoplado ao protótipo de um conversor dc/dc topologia Booster

Low voltage solar panels increase the reliability of solar panels due to reduction of in series associations the configurations of photovoltaic cells. The low voltage generation requires DCDC converters devices with high efficiency, enabling raise and regulate the output voltage. This study analyzes the performance of a photovoltaic panel of Solarex, MSX model 77, configured to generate an open circuit voltage of 10.5 V, with load voltage of 8.5 V, with short circuit current of 9 A and a power of 77 W. The solar panel was assembled in the isolated photovoltaic system configuration, with and without energy storage as an interface with a DCDC converter, Booster topology. The converter was designed and fabricated using SMD (Surface Mounted Devices) technology IC (integrated circuit) that regulates its output voltage at 14.2 V, with an efficiency of 87% and providing the load a maximum power of 20.88 W. The system was installed and instrumented for measurement and acquisition of the following data: luminosities, average global radiation (data of INPE Instituto Nacional de Pesquisas Espaciais), solar panel and environment temperatures, solar panel and DC-DC converter output voltages, panel, inverter, and battery charge output currents. The photovoltaic system was initially tested in the laboratory (simulating its functioning in ideal conditions of operation) and then subjected to testing in real field conditions. The panel inclination angle was set at 5.5°, consistent with the latitude of Natal city. Factors such as climatic conditions (simultaneous variations of temperature, solar luminosities and ra diation on the panel), values of load resistance, lower limit of the maximum power required by the load (20.88 W) were predominant factors that panel does not operate with energy efficiency levels greater than 5 to 6%. The average converter efficiency designed in the field test reached 95%

Desenvolvimento de filtros cerâmicos impregnados com nanopartículas de prata para desinfecção de água potável

Brazil has vast amounts of hydric resources, whose quality has been deteriorating due to pollutant dumping. Household waste disposal is one of the main sources of water pollution, stimulating bacteria proliferation and introducing microorganisms, including those from fecal matter. Conventional water disinfection methods are a solution, but on the downside, they lead to the formation byproducts hazardous to human health. In this study, aiming to develop bactericidal filters for the disinfection of drinking water; silver nanoparticles were deposited on alumina foams through three routes: sputtering DC, dip coating and in situ chemical reduction of silver nitrate. The depositions were characterized through X-ray diffraction, scanning electron microscopy and EDS element mapping. The influence of the depositions on permeability and mechanical properties of the ceramic foams was assessed and, in sequence, a preliminary antibacterial efficiency analysis was carried out. Characterization results indicate that the chemical reduction routes were efficient in depositing homogeneously distributed silver particles and that the concentration of the metallic precursor salt affects size and morphology of the particles. The antibacterial efficiency analysis indicates that the chemical reduction filters have potential for water disinfection

Determinação de parâmetros de qualidade para formas farmacêuticas homeopáticas

All medicine, whether allopathic or homeopathic, must go through strict quality control, which must ratify their characteristics throughout the period of validity. During the time of preparation and storage, solutions of the drugs are in permanent contact with packaging materials that can release undesirable substances to the solution. Several factors may influence the release of packing materials, and factorial design (FD) is a useful tool for analyzing the phenomenon. The aim of this study was the determination of quality parameters for Homeopathic solid (globules) and liquid (drops) dosage forms. It was carried out analysis in homeopathic globules for weight variation, mechanical strength, and moisture content uniformity. For liquid preparations, standard solutions were prepared from natural rubber bulbs, which were subjected to exhaustive extraction with two ethanol solutions (30 and 70%) in the ultrasonic bath for 20 minutes at 25°C and 50°C in three successive cycles. Studies of transfer have been made within five days, by spectrophotometric analysis in the UV region at 312 nm with λmáx and 323 nm for samples in 70% ethanol and 30% respectively. PH values were analyzed. We also conducted two FD studies, where the first, the three-level variables were solvent (chloroform, ethanol and nhexane), sample mass (30, 60 and 90mg), particle size (large disk, small disk and powder sample). In the second study, the solvent level variables were different ethanolic degrees (EtOH 30%, 70% and pure). The percentage of lending in the solutions was 5.5%, 12.4%, 24.2% and 41% of the total estimated in the reference solution. The values of rate constants of transfer were determined in the order of 0.0134 days-1 and 0.0232 days-1 in absorbance values, the solutions in ethanol at 30% and 70% respectively. These results suggest that the speed of transfer of materials from rubber is affected both by the nature of the vehicle as by the temperature

Protótipo de uma unidade com tri-geração de energia para utilizações remotas: aplicação de módulo secondutivo gerador termoelétrico

The generation for termoeletricity is characterized as a solid process of conversion of thermal energy (heat) in electric without the necessity of mobile parts. Although the conversion process is of low efficiency the system presents high degree of trustworthiness and low requisite of maintenance and durability. Its principle is based on the studies of termogeneration carried through by Thomas Seebeck in 1800. The frank development of the technologies of solid state for termoeletricity generation, the necessity of the best exploitation of the energy, also with incentive the cogeneration processes, the reduction of the ambient impact allies to the development of modules semiconductors of high efficiency, converge to the use of the thermoeletric generation through components of solid state in remote applications. The work presents the development, construction and performance evaluation of an prototype, in pilot scale, for energy tri-generation aiming at application in remote areas. The unit is composed of a gas lamp as primary source of energy, a module commercial semiconductor for thermoelectric generation and a shirt for production of the luminosity. The project of the device made compatible a headstock for adaptation in the gas lamp, a hot source for adaptation of the module, an exchanger of to be used heat as cold source and to compose first stage of cogeneration, an exchanger of tubular heat to compose second stage of cogeneration, the elaboration of a converter dc-dc type push pull, adequacy of a system of acquisition of temperature. It was become fullfilled assembly of the prototype in group of benches for tests and assay in the full load condition in order to evaluate its efficiency, had been carried through energy balance of the unit. The prototype presented an electric efficiency of 0,73%, thermal of 56,55%, illumination of 1,35% and global of 58,62%. The developed prototype, as the adopted methodology of assay had also taken care of to the considered objectives, making possible the attainment of conclusive results concerning to the experiment. Optimization in the system of setting of the semicondutor module, improvement in the thermal insulation and design of the prototype and system of protection to the user are suggestions to become it a commercial product

Farelo do bagaço de caju na restrição alimentar qualitativa para suínos em terminação

The objective of this study was to evaluate the effects of the use of cashew bagasse bran (CBB) as food ingredient in qualitative feed restriction programs on the carcass traits, meat quality, organs weight and intestinal morphometry of barrows and gilts. Twenty – four crossbred pigs were used (12 barrows and 12 gilts) with an average initial body weight of 57.93 ± 3.67 kg/LW. The experimental designs was in randomized blocks 3x2 factorial arrangement with three level (0%, 15% e 30% CBB), two genders (barrows and gilts) and four repetition. A total of twenty-four instalments. The treatments were composed of basal diet (BD) formulated with corn, soybean meal and commercial base mix for finishing pigs, being containing different levels of CBB. At the end of the trial period the animals were slaughtered for the evaluation of the meat quality, traits carcass, Absolute Weight (AW) and Relative Weight (RW) of the organs and morphometric study of small intestine fragment. The inclusion of (CBB) in the diets did not affect the traits carcass of gilts, but interfered in the traits carcass of the barrow positively, increasing the yield of meat into cold carcass and reducing the thickness of subcutaneous fat, without affecting the fatty acid profile. However, we observed increased weight of organs and partial volume of absortiva mucosa of gilts. In the comparison between sex was observed a greater liver weight (AW) and (RW), and surface density of absortiva mucosa of barrow. The use of CBB was considered as ingredient to be used in programs of qualitative feed restriction for finishing pigs.

Farelo do bagaço de caju na restrição alimentar qualitativa para suínos em terminação

The objective of this study was to evaluate the effects of the use of cashew bagasse bran (CBB) as food ingredient in qualitative feed restriction programs on the carcass traits, meat quality, organs weight and intestinal morphometry of barrows and gilts. Twenty – four crossbred pigs were used (12 barrows and 12 gilts) with an average initial body weight of 57.93 ± 3.67 kg/LW. The experimental designs was in randomized blocks 3x2 factorial arrangement with three level (0%, 15% e 30% CBB), two genders (barrows and gilts) and four repetition. A total of twenty-four instalments. The treatments were composed of basal diet (BD) formulated with corn, soybean meal and commercial base mix for finishing pigs, being containing different levels of CBB. At the end of the trial period the animals were slaughtered for the evaluation of the meat quality, traits carcass, Absolute Weight (AW) and Relative Weight (RW) of the organs and morphometric study of small intestine fragment. The inclusion of (CBB) in the diets did not affect the traits carcass of gilts, but interfered in the traits carcass of the barrow positively, increasing the yield of meat into cold carcass and reducing the thickness of subcutaneous fat, without affecting the fatty acid profile. However, we observed increased weight of organs and partial volume of absortiva mucosa of gilts. In the comparison between sex was observed a greater liver weight (AW) and (RW), and surface density of absortiva mucosa of barrow. The use of CBB was considered as ingredient to be used in programs of qualitative feed restriction for finishing pigs.

Social determinants of dental treatment needs in Brazilian adults

Background The chronic cumulative nature of caries makes treatment needs a severe problem in adults. Despite the fact that oral diseases occur in social contexts, there are few studies using multilevel analyses focusing on treatment needs. Thus, considering the importance of context in explaining oral health related inequalities, this study aims to evaluate the social determinants of dental treatment needs in 35–44 year old Brazilian adults, assessing whether inequalities in needs are expressed at individual and contextual levels. Methods The dependent variables were based on the prevalence of normative dental treatment needs in adults: (a) restorative treatment; (b) tooth extraction and (c) prosthetic treatment. The independent variables at first level were household income, formal education level, sex and race. At second level, income, sanitation, infrastructure and house conditions. The city-level variables were the Human Development Index (HDI) and indicators related to health services. Exploratory analysis was performed evaluating the effect of each level through calculating Prevalence Ratios (PR). In addition, a three-level multilevel modelling was constructed for all outcomes to verify the effect of individual characteristics and also the influence of context. Results In relation to the need for restorative treatment, the main factors implicated were related to individual socioeconomic position, however the city-level contextual effect should also be considered. Regarding need for tooth extraction, the contextual effect does not seem to be important and, in relation to the needs for prosthetic treatment, the final model showed effect of individual-level and city-level. Variables related to health services did not show significant effects. Conclusions Dental treatment needs related to primary care (restoration and tooth extraction) and secondary care (prosthesis) were strongly associated with individual socioeconomic position, mainly income and education, in Brazilian adults. In addition to this individual effect, a city-level contextual effect, represented by HDI, was also observed for need for restorations and prosthesis, but not for tooth extractions. These findings have important implications for the health policy especially for financing and planning, since the distribution of oral health resources must consider the inequalities in availability and affordability of dental care for all.

Desenvolvimento de filtros cerâmicos impregnados com nanopartículas de prata para desinfecção de água potável

Brazil has vast amounts of hydric resources, whose quality has been deteriorating due to pollutant dumping. Household waste disposal is one of the main sources of water pollution, stimulating bacteria proliferation and introducing microorganisms, including those from fecal matter. Conventional water disinfection methods are a solution, but on the downside, they lead to the formation byproducts hazardous to human health. In this study, aiming to develop bactericidal filters for the disinfection of drinking water; silver nanoparticles were deposited on alumina foams through three routes: sputtering DC, dip coating and in situ chemical reduction of silver nitrate. The depositions were characterized through X-ray diffraction, scanning electron microscopy and EDS element mapping. The influence of the depositions on permeability and mechanical properties of the ceramic foams was assessed and, in sequence, a preliminary antibacterial efficiency analysis was carried out. Characterization results indicate that the chemical reduction routes were efficient in depositing homogeneously distributed silver particles and that the concentration of the metallic precursor salt affects size and morphology of the particles. The antibacterial efficiency analysis indicates that the chemical reduction filters have potential for water disinfection