Proposta de zoneamento ambiental visando a proteção dos recursos hídricos de uma bacia hidrográfica

One of the most important natural resources for sustaining human life, water, has been losing the basic requirements of quality and quantity sufficient enough to attend the population due to water contamination'problems, often caused by human beings themselves. Because of this, the sources of this resource are often located in remote places of the natural environment to ensure the quality of the water. However, when urban expansion began to occupy these areas, which were once regarded as distant, environmental pollution problems began to occur due to occupation of the land without planning. Based on this occurrence, this study aims to propose environmental zoning for the Maxaranguape river watershed in order to protect its water resources. This is important because this river can serve as a source of supply for the metropolitan area of Natal, the capital of Rio Grande do Norte. In accordance to this proposition, the model of natural soil loss vulnerability (CREPANI et al., 2001), the model of aquifer pollution vulnerability (FOSTER et al., 2006), and the legal incompatibility map (CREPANI et al., 2001) were used to delimit the zones. All this was done with Geographic Information System (GIS) and also created a geographic database update of the basin. The results of the first model mentioned indicated that 63.67% of the basin was classified as moderately stable / vulnerable, 35.66% as moderately vulnerable, and 0.67% as vulnerable. The areas with high vulnerability degree correspond with sand dunes and river channels areas. The second model indicated that 2.84% of the basin has low vulnerability, 70.27%) has median vulnerability, and 26.76% and 0.13% has high vulnerability and extreme vulnerability, respectively. The areas with the highest vulnerability values also refer to part of the sand dunes and river channels besides other areas such as Pureza urban area. The legal incompatibility map indicated that the basin has 85.02 km2 of Permanent Protection Area (PPA) and 14.62% of this area has some incongruity of use. Based on these results it was possible to draw three main zones: Protection and Sustainable Use Zone (PSUZ), Protection and Environmental Restoration Zone (PERZ) and Environmental Control Zone, which are divided into A, B and C. The PSUZ refer to the coastal areas of the basin, where the sand dunes are located. These sites should be areas of environmental protection and of sustainable urban expansion. The ZPRA refer to river channels, which are in high need of rehabilitation. The third zone corresponds to the rest of the basin which should have, in general, the mapping of possible sources of contamination for further control on the use and occupation of the river

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.