Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Parâmetros urbanísticos na regulação do uso e ocupação do solo: estudo da densidade e do coeficiente de aproveitamento nos planos diretores de Natal de 1994 e 2007

A Constituição Federal de 1988 e o Estatuto da Cidade estabelecem o Plano Diretor como instrumento básico da política de ordenamento territorial, tendo como princípio fundamental o cumprimento da função social da propriedade e do direito à cidade. Na perspectiva de adequação às diretrizes e objetivos da política urbana estabelecidos em 1988, o município de Natal elaborou os Planos Diretores de 1994 e 2007, definindo instrumentos e parâmetros de regulação do uso e ocupação do solo possíveis de assegurar o cumprimento da função social da propriedade urbana e de gerar subsídios ao planejamento e à gestão da cidade. Apesar de Natal ter sido um dos municípios brasileiros pioneiros na adoção desses princ pios, antecipando e incorporando os instrumentos que em 2001 viriam a ser definidos no Estatuto da Cidade, identifica-se que alguns desses instrumentos e parâmetros direcionados à regulação do uso e ocupação do solo não tiveram sua aplicação plena, a exemplo do mecanismo de acompanhamento e controle dado pelo Estoque de Área Edificável e da Densidade, que foi substituída pelo Coeficiente de Aproveitamento no Plano Diretor de 2007. Questionando esse procedimento, busca-se na presente pesquisa investigar de que maneira essa substituição do parâmetro densidade pelo coeficiente de aproveitamento influenciou na capacidade da gestão pública de regular os processos de uso e ocupação do solo, de forma a adequar a sua intensificação ao suporte da infraestrutura instalada. Foram tomadas como referência teórico-conceitual as contribuições sobre a prática de planejamento urbano no Brasil, nos marcos do ideário da reforma urbana, com destaque para as reflexõe s de Flávio Villaça, Orlando Alves Santos Junior e Daniel Todtmann Montandon, Luiz César de Q. Ribeiro, Raquel Rolnik, Ermínia Maricato, Laura Machado de Bueno e Renato Cymbalista, José Roberto Bassul e Carlos F. Lago Burnett, e, com relação aos parâmetros de controle urbanístico, o estudo identifica as diferentes abordagens sobre a densidade urbana e o coeficiente de aproveitamento com base nas reflexões de Claudio Acioly Jr., Forbes Davidson, Juan Luis Mascaró, Ricardo Ojima, Marcelo de Souza, José Rámon Navarro Vera e Armando Ortuño Padilla, Nestor Goulart Reis, Marta Dora Grostein e Susana Ricardo Alves. Como conclusão, discute-se a hipótese formulada, inicialmente, de que a mudança de parâmetros verificada colocou limites para o município realizar uma gestão adequada do solo urbano e, portanto, de fazer cumprir a função social da propriedade, considerando a necessidade de adequação entre a intensificação do uso e ocupação do solo e a infraestrutura instalada

Metagenômica comparativa de solo de regiões de mata atlântica e caatinga do estado do Rio Grande do Norte - Brasil

The microorganisms play very important roles in maintaining ecosystems, which explains the enormous interest in understanding the relationship between these organisms as well as between them and the environment. It is estimated that the total number of prokaryotic cells on Earth is between 4 and 6 x 1030, constituting an enormous biological and genetic pool to be explored. Although currently only 1% of all this wealth can be cultivated by standard laboratory techniques, metagenomic tools allow access to the genomic potential of environmental samples in a independent culture manner, and in combination with third generation sequencing technologies, the samples coverage become even greater. Soils, in particular, are the major reservoirs of this diversity, and many important environments around us, as the Brazilian biomes Caatinga and Atlantic Forest, are poorly studied. Thus, the genetic material from environmental soil samples of Caatinga and Atlantic Forest biomes were extracted by direct techniques, pyrosequenced, and the sequences generated were analyzed by bioinformatics programs (MEGAN MG-RAST and WEBCarma). Taxonomic comparative profiles of the samples showed that the phyla Proteobacteria, Actinobacteria, Acidobacteria and Planctomycetes were the most representative. In addition, fungi of the phylum Ascomycota were identified predominantly in the soil sample from the Atlantic Forest. Metabolic profiles showed that despite the existence of environmental differences, sequences from both samples were similarly placed in the various functional subsystems, indicating no specific habitat functions. This work, a pioneer in taxonomic and metabolic comparative analysis of soil samples from Brazilian biomes, contributes to the knowledge of these complex environmental systems, so far little explored

Análise e avaliação dos elementos de penetração no solo de equipamentos rodoviários após revestimento

The main objective is to analyze the abrasive wear resistance to the low stress of the elements that make up the organs of road machinery that are exposed directly to contact with abrasives. These samples were analyzed after these elements are coated superficially by the process of welding electrode coated with (SAER) and the manual process of coating type LVOF thermal spraying. As well, is to provide suggestions for a better recovery and return of these elements, which are reducing costs and avoiding downtime in the fronts of service. The samples were made from a substrate of carbon ABNT 1045 tempered steel, following the same specifications and composition of metals and alloys of constituents was followed the standard governing the dimensions of these samples and in accordance with the corresponding size. The results were evaluated by testing the hardness, abrasion resistance to wear by the low stress and the loss of volume involving the microstructure of coatings analyzed

Estudo da incorporação de cascalho proveniente da perfuração de poços de petróleo em formulações para tijolos de solo-cimento

The present work is to study the characteristics and technological properties of soil-cement bricks made from binary and ternary mixtures of Portland cement, sand, water, with or without addition of gravel from the drilling of oil wells, which could be used by industry, aiming to improve its performance and reduce cost by using the residue and, consequently, increasing its useful life. The soil-cement bricks are one of the alternatives to masonry construction. These elements, after a short curing period, provide compressive strength similar to that of solid bricks and ceramic blocks, and the higher the resistance the higher the amount of cement used. We used the soil from the city of São José do Mipibu / RN, the banks of the River Baldun, cement CPIIZ-32 and residue of drill cuttings from oil wells drilling onshore wells in the town of Mossley, RN, provided Petrobras. To determine the optimum mix, we studied the inclusion of different residues (100%, 80%, 70%, 60% and 50%) where 15 bodies were made of the test piece. The assessment was made of bricks made from simple compression tests, mass loss by immersion and water absorption. The experimental results proved the efficiency and high utilization of the waste from the drilling of oil wells, making the brick-cement-soil residue with a higher strength and lower water absorption. The best result in terms of mechanical strength and water absorption for the ternary mixture was 10% soil, 14% cement and 80% residue. In terms of binary mixtures, we obtained the best result for the mix-cement residue, which was 14% cement incorporated in the residue

Estudo da incorporação da cal em composições binárias de solo-cimento para produção de tijolos maciços

The use of binders in the soil for the production of solid bricks is an old construction technique that has been used by several civilizations over time. At the same time, the need for environmental preservation and the tendency of scarcity of natural resources make the construction invest in researching new concepts, methods and materials for building systems for the sustainability of their economic activities. Thus arises the need to obtain building materials with low power consumption, capable of reducing the growing housing shortage of rural and urban population. Currently, research has been conducted on this topic to better understand the cementitious and pozzolanic reactions that occur in the formation of the microstructure of the soil-cement when added to other materials such as, for example, lime, and the relationship between microstructure and formed interfaces with the physical, mechanical and chemical analysis in compounds made from these ternary compositions. In this context, this study aimed to analyze the results of the influence of the incorporation of lime to the soil-cement to form a ternary mixture to produce soil-cement bricks and mortar without structural purposes. From the inclusion of contents of 6 %, 8 %, 10% and 12% lime to the soil, and soil-cement mixes in amounts of 2 %, 3 %, 4 % and 5 % were shaped-bodies of -cylindrical specimens to determine the optimum moisture content and maximum dry apparent specific weight. Then they were cured, and subjected to the tests of compressive strength, absorption and durability modified. Compositions obtained the best results in the tests performed on the bodies-of-proof cylindrical served as a parameter for molding of solid bricks, which underwent the same experimental methodology previously cited. The raw materials used, as well as compositions in which the bricks were molded solid, were characterized by physical and chemical tests, X-ray diffraction and scanning electron microscopy. The results obtained in the study indicate that the compositions studied, that showed the best results in terms of compressive strength, water absorption and durability ternary composition was soil, 10 % cement and 2 % lime

Avaliação da correlação entre os parâmetros, carbono orgânico total e elementos tóxicos, em solo de um posto de serviço e revenda de combustíveis

Today a major responsibility for the contamination of soil and groundwater and surface water are establishments known as gas stations of fuel which has attracted increasing attention from both the general population as the state agencies of environmental control due to leaks in storage tanks and mainly to disruption of pipe corrosion of tanks and pumping. Other services, like oil changes and car wash are also causes for concern in this type of establishment. These leaks can cause or waste produced, and the contamination of aquifers, serious health problems and public safety, since most of these stations located in urban areas. Based on this, the work was to evaluate soil contamination of a particular service station and fuel sales in the city of Natal, through the quantification of heavy metals like Cd, Cu, Cr, Ni, Pb, Zn of total organic carbon (TOC) and organic matter using different techniques such as optical emission spectrometry with inductively coupled plasma source (ICP OES), Total Organic Carbon analyzer and gravimetric analysis respectively. And also to characterize the soil through particle size analysis. Samples were taken in 21 georeferenced points and collected in the same period. The soils sampled in sampling stations P3, P5, P6, P10, P11, P12, P13, P14, P15, P17, P18 and P20 showed the smallest size fractions ranging from fine sand to medium sand. The other study sites ranged from fine sand to medium sand, except the point P8 showed that only the type size medium sand and P19, indicating a particle size of the coarse type. The small correlation of organic matter with the elements studied in this work suggests that these are not of anthropogenic origin but geochemical support

Avaliação de HPA e BTEX no solo e água subterrânea, em postos de revenda de combustíveis: estudo de caso na cidade de Natal -RN

The retail fuel stations are partially or potentially polluters and generators of environmental accidents, potentially causing contamination of underground and surface water bodies, soil and air. Leaks in fuel retail stations´ underground storage systems are often detected in Brazil and around the world. Monoaromatic hydrocarbons, BTEX (benzene, toluene, ethylbenzene and xylenes) and polycyclic aromatic hydrocarbons (PAHs) are an indication of the presence of contamination due to its high toxicity. This paper presents a case study of contamination in a Fuel Retail Station by petroleum derivative products in the city of Natal. For identification and quantification of the hydrocarbons, EPA analytical methods were used. The values of benzene quantified by EPA method 8021b CG-PID/FID, ranged from 1.164 to 4.503 mg.Kg-1 in soil samples, and from 12.10 to 27,639 μg.L-1 in underground water samples. Among the PAHs, naphthalene and anthracene showed the most significant results in soil samples, 0.420 to 15.46 mg.Kg-1 and 0.110 to 0,970 mg.Kg-1, respectively. In underground water samples, the results for Naphthalene varied between 0.759 and 614.7 μg.L-1. PAHs were quantified by EPA Method 8270 for GCMS. All of the results for the chemical analysis were compared with the values for the CONAMA 420/2009 resolution. The results for benzene (27,639 μg.L-1) showed levels highly above the recommended by the CONAMA 420 resolution, wherein the maximum permissible for underground water is 5 μg.L-1. This is a worrying factor, since underground water makes up 70% of the city of Natal´s water supply

Arthropoda de solo em um ecossistema semi-árido da região neotropical: composição, variabilidade temporal e estratificação

Caatinga is an important laboratory for studies about arthropods adaptations and aclimatations because its precipitation is highly variable in time. We studied the effects of time variability over the composition of Arthropods in a caatinga area. The study was carried out at a preservation area on Almas Farm, São José dos Cordeiros, Paraíba. Samples were collected in two 100 m long parallel transects, separated for a 30 m distance, in a dense tree dominated caatinga area, between August 2007 and July 2008. Samples were collected in each transect every 10 m. Ten soil samples were taken from each transect, both at 0-5 cm (A) and 5-10 cm (B) depth, resulting in 40 samples each month. The Berlese funnel method was used for fauna extraction. We registered 26 orders and the arthropods density in the soil ranged from 3237 to 22774 individuals.m-2 from January 2007 to March 2008, respectively. There was no difference between layers A and B regarding orders abundance and richness. The groups recorded include groups with few records or that had no records in the Caatinga region yet as Pauropoda, Psocoptera, Thysanoptera, Protura and Araneae. Acari was the most abundant group, with 66,7% of the total number of individuals. Soil Arthropods presented a positive correlation with soil moisture, vegetal cover, precipitation and real evapotranspiration. Increases in fauna richness and abundance were registered in February, a month after the beginning of the rainy season. A periodic rain events in arid and semiarid ecosystems triggers physiological responses in edafic organisms, like arthropods. Edafic arthropods respond to time variability in the Caatinga biome. This fauna variation has to be considered in studies of this ecosystem, because the variation of Arthropods composition in soil can affect the dynamics of the food web through time

Efeitos das variáveis ambientais locais sobre a abundância, a riqueza e a biomassa da macrofauna de solo em um ecossistema semiárido no estado do rio grande do norte, nordeste do brasil

The soil macrofauna is influenced to several biotic and abiotic environmental factors, from changes in the physical environment to a variety of interactions among the species involved, affecting the patterns of biodiversity of soil fauna. The power and specificity of the mechanisms that act on soil organisms vary greatly depending on environmental conditions at different scales of space and time. The Caatinga has great spatial heterogeneity of vegetation, climate and soil, so the soil macrofauna would follow this local spatial variation in the environment? This study aimed to investigate the effects of local environmental variables on biological parameters (taxa richness, total abundance and biomass) of soil macrofauna in a fragment of caatinga in João Câmara, Rio Grande Norte, Northeast Brazil. The study was conducted in the Cauaçu farm, where a grid of 2000m x 500m was drawn, and later, 30 sampling points were randomly selected. The methodology used to collect the macrofauna was the TSBF method. We tested the effects of 10 environmental variables on macrofauna across the plots and across the layers of soil. The hypothesis that macrofauna soil responds to changes in the environment was not supported throughout the plots, but was confirmed to soil layers. The soil macrofauna shows a pattern of concentration in the surface layer and decreases considerably in the deeper layers. This pattern had significant and positive relationship with the aerial plant biomass and fine root stock. The aerial plant biomass releases plant necromass that accumulates in the surface layer, providing an important source of resource and shelter for soil macrofauna, explaining their greater abundance in this layer. The roots are used as a means for the arrival of nutrients to the soil from the primary production, thus a greater amount of root conditions higher food intake for macrofauna, especially the herbivores

Alteração da qualidade do solo em zona ripária sob diferentes usos: potencial de poluição para um manancial tropical

The demographic growth press environments that are more susceptible to perturbations, like riparian areas, without knowing about the effects of replacing these natural environments by different land uses on soil quality and, consequently, on watershed. The study of soil quality has evolved as an important tool for soil sustainable management of this component of the biosphere that affects aquatic and terrestrial ecosystems functions. Thus, physical and chemical soil proprieties were measured to assess soil quality under different land uses (agricultural, pasture, urban, industrial and natural vegetation,) in the riparian zone of Extremoz Lake, an important human water source, evaluating whether the soil offers potential risk to water pollution. Data were subjected to descriptive statistics and Principal Component Analysis (PCA). The results showed negative changes in soil quality such as alkalinization and increase in P, Pb, Mn and Zn contents in most anthropized areas. The sandy texture and low organic matter content in all soils showed the fragility of the soil to erosion and leaching of elements in excess to water bodies, evidencing that this soils has potential to diffuse contaminants. Conservative management of soil is necessary to provide an adequate ecological state in riparian zones of the Extremoz Lake, thus allowing controlling and buffering diffuse sources of pollution to this important water supply source

Televisão em solo educativo: educando o olhar

This work supplies a reflection concerning the presence of the daily television in the children s lives. It points with respect to the necessity of the incorporation of the nature of the medias and information in the educative proposals in way to promote the approach of the two areas in the junction of its respective epistemologies. It considers the development of a visual acuity for the student staff, pointing out the paper of the educator as a promoter of this taken over on a contract basis. Therefore, we present a research of field, carried through in some public and private primary schools in Natal and other cities that are part of the Grande Natal , trying to show with what perspective the teachers use the languages in this stage of education, prioritizing the television elements. As elements of the collection of the information, we made use of half-structuralized interviews, beyond comments directed for the moments where the teachers used the television with educative intention. As results, we noticed that some considerable part of the involved educators still don t get to conceive the television as integrating part of the roll of the languages, using this resource in a limited way, restricting to the contact with sets of documentaries and essentially educative productions, besides the use of objectives directed toward the entertainment, forgetting the opened TV, present in the daily lives of the children since the tender age

Estabilização de um Solo com Cimento e Cinza de Lodo Para Uso em Pavimentos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Impactos do estresse salino e da cobertura morta nas características químicas do solo e no desenvolvimento do amaranto

Availability of good quality water has been reduced vertiginously, over the last decade, in the world. In some regions, the water resources have high concentration of the dissolved salts, these characteristics of the water make it s use impossible. Water quality can be a limitation for irrigated agriculture, principally in regions of arid or semiarid climate where the water resources are generally saline and are exposed at high evaporation ratio. For that reason, precipitation of the salts occurs near the soil surface and those salts themselves cumulate in the vegetal tissue, reducing the soil fertility and crop production. The adoption of tolerant crop to the water salinity and soil salinity, adaptable to the climatic conditions is other emergent necessity. This work had the goal of studying the effects of four salinity levels of the irrigation water salinity and use of mulch, dried leaves of Forest mangrove (Acacia mangiumWilld), in cultivated soil with amaranth (Amaranthus cruentus, BRS Alegria variety), in greenhouse. It was utilized the transplant of plants to PVC columns, containing 30 kg of silty loam soil, 10 days after emerging, with space of 50 x 50 cm between lines. Treatments were composed by combination of four levels of salinity (0.147; 1.500; 3.000 e 4.500 dS m-1), obtained by addition NaCl (commercial) to irrigation water and soil with and without protection, by mulch. A factorial system 4 x 2 was used with four repetitions, totalizing 32 parcels. The concentrations of nutrients in soil solution have been evaluated, in the dry matter of the vegetal tissue (roots, stem, leaves and raceme residue), at the end of the vegetative cycle. The use of soil protection reduced time for the beginning inflorescence of plants, at the same time, the increase of the salinity delayed this phase of amaranth development. The use of the mulch effectively increased the height, stem diameter, area of the larger leaf, humidity and dry matter content and amaranth grain production. The vegetal species showed salinity tolerance to experimented levels. The adopted treatments did not affect the pH values, exchangeable cation contents, electrical conductivity of soil solution (EC1:5) and saturated extract (ECSE), and Ca+2, Mg+, Fe+2 and Mn+2 contents, in the soil solution. The increase of the salinity concentration in the irrigation water inhibited the mineralization process of the organic matter (OM) and, consequently, the efficiency in the it´s utilization by plants, at the same time, produced increase in the values of the exchangeable sodium percentage (ESP), sodium adsorption ratio (SAR) and potassium adsorption ratio (PAR), in the soil solution. Therefore, the use of the mulch did not affect the first three parameters. The protein and nutrient contents: K+, Ca+2, P, Mg+2 e Cu+2, in amaranth grains, were improved by tillage condition. The raceme residues showed chemical/nutritional composition that makes advantageous its application in animal ration. In this context, it follows that amaranth tolerate the saline stress, of the irrigation water, until 4.500 dS m-1, temperature and relative humidity of the air predominant in the experimental environment