Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.

Reconfigurações industriais das regiões metropolitanas do Nordeste: uma análise a partir do emprego formal

Industrial development experienced by Brazil from the 1950s, changed the concentration of population in the country. The process of development of domestic industry, concentrated in urban areas, crowded growing portion of the population.The Southeast region during the first stage of industrialization driven by the state, with the implementation of Plan goals, captained the major industrial projects implemented in the period and became the main industrial center of the country.In the decade from 1960 to 1980 the state action was marked by numerous regional development projects, softening the industrial concentration and Brazilian investment redirected to the Northeast.The second National Development Plan implemented in the 1970s led to major investments Northeast.This period marked the widespread urban growth and institutionalization of the first metropolitan areas in Brazil.The change of this developmental process is altered with the fiscal and financial crisis of the state in the 1980s and 1990s and spending cuts aimed at national development, reorienting the economy to liberal policies of economic liberalization and reduction of activity in the economy.Industrial policy was relegated to local development plans from the 1990s to the federating units fitting the wide use of tax incentives, the "war tax" to the continued industrialization process.In this context of the national economy work seeks to analyze the industrial setting in the metropolitan areas of Fortaleza, Recife and Salvador between 1995 and 2010.Although the metropolitan areas of Fortaleza, Recife and Salvador are the main urban centers of the Northeast, responsible for the advancement of industrial development, reconfigurations occurred between 1995 and 2010 by changing the level of industrial specialization built by regional division of labor in these regions.The work will be carried out by the method of descriptive analysis of the literature review on regional and urban development.Constitute quantitative method as the secondary data analysis of formal employment from the Annual Social Information (RAIS) Ministry of Labour and Employment (MTE).Using data RAIS / MTE analyzes the industrial specialization index using the Locational Quotient (LQ).Thus, it is assumed as a parameter analysis QL> 1, when the region has become specialized in a particular sector or QL <1, when the region does not have expertise in industrial sector analyzed.The conclusion of study indicates that there was in these metropolitan areas maintained the same bias hub.Fiscal policies, the states, was not successful in diversifying the productive structure and the Northeast region itself.This result is demonstrated by the need and dependence on state investments in the region to promote development.Industrial policies of recent years have been positive to meet the objectives of employment generation, but there must be specific policies for better diversification of production, in addition to integrating the economy of the Northeast sector and regionally

Estudo da incorporação de resíduo industrial polimérico ao CAP

This work presents the incorporation of an industrial polymeric waste into a petroleum asphalt cement with penetration grade 50-60 (CAP 50-60). The main goal of this research is the development of a polymer-modified asphalt, with improvements in its physical properties, in order to obtain a more resistant material to the traffic loads. Furthermore, the use of this polymeric waste will result in economic and environmental benefits. The CAP 50-60 used in this research was kindly supplied by LUBNOR Lubrificantes e Derivados de Petróleo do Nordeste (produced in Fazenda Belém Aracati - Ceará) and the industrial polymeric waste was provided by a button manufacturer industry, located in Rio Grande do Norte state. This polymeric waste represents an environmental problem due to its difficulty in recycling and disposal, being necessary the payment by the industry to a landfill. The difficulty in its reuse is for being this material a termofixed polymer, as a result, the button chips resulting from the molding process cannot be employed for the same purpose. The first step in this research was the characterization of the polymeric waste, using Differential Scanning Calorimetry (DSC) Infrared spectroscopy (IR spectroscopy), and Thermogravimetric analysis (TGA). Based on the results, the material was classified as unsaturated polyester. After, laboratory experiments were accomplished seeking to incorporate the polymeric waste into the asphalt binder according to a 23 experimental factorial design, using as main factors: the polymer content (2%, 7% and 14%), the temperature of the mixture (140 and 180 oC) and the reaction time (20 and 60 minutes). The characterization of the polymer-modified asphalt was accomplished by traditional tests, such as: penetration, ring and ball softening point, viscosity, ductility and flash point temperature. The obtained results demonstrated that the addition of the polymeric waste into the asphalt binder modified some of its physical properties. However, this addition can be considered as a feasible alternative for the use of the polymeric waste, which is a serious environmental and technological problem.

Inundações urbanas no semiarido nordestino: o caso da cidade de Pau dos Ferros - RN

The Apodi river basin, particularly within the snippet that crosses Pau dos Ferros - RN city, place anthropogenic actions that interfere in the dynamic environment by modifying the local landscape. The reflection of these actions can be seen in the floods that occur in rainy periods (February to may) virtually every year in the city. It is important to stress that the project of integration of the waters of the San Francisco basin with the northern basin of Northeastern will perennial the main channel of the river basin, and generate greater impacts in the region. This work sought to define a methodology able to delimit areas susceptible to flooding in cities of semiarid Northeast based on the Pau dos Ferros RN city. The dissertation is divided into two chapters and introduction. The introduction presents a theoretical frame based on discussion of the concept of risk, their main characteristics and subdivisions; floods; geotecnologies; Apodi River basin; municipal data Pau dos Ferros RN and design integration of Francisco basin with the northern basins Northeast. The first chapter evaluates the urban expansion process between 1987 and 2008, delimiting the flood areas and analyzes the relationship between urban growth and retention areas. The second chapter identifies the flood risk areas in the Pau dos Ferros city. The methodology used was based on tools of geographic information system GIS from software SPRING/INPE 5.1, as well as bibliographical, satellite images, aerial photographs and field activities. The results obtained enabled view the rapid expansion of the urban area of Pau dos Ferros, which has doubled in a period of 22 years. The population density checks with greater intensity in South-central portion of the city, in flood areas and not flood (Cap. 01). It was noted also that some neighborhoods along the River Apodi are susceptible to more instances of flooding ranging from minimum to maximum, while in neighborhoods near the Riacho Cajazeiras floods occur to a lesser extent because of altimetry higher and lower water volume. (Cap. 02). It is expected that this work will help in the preparation of flood risk municipal map subsidising managers in implementing public policies targeted to the softening of urban flood-related issues in Pau dos Ferros RN and serve as a model for mapping of other cities with similar characteristics analyzed in this work

Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.