Utilização de nanosílica como aditivo estendedor para pastas cimentantes de baixa densidade destinadas à cimentação de poços petrolíferos

Cementing operations are conducted at different times of the well s life and they have high importance, because the functions are fundamental to keep good properties during a long life of the well, such as, maintain the mechanical stability of the well, to promote the isolation hydraulic and support the tubing. In some situations, the rocky zones have low fractures pressures and require the use of lightweight slurries to prevent the hydrostatic pressure in the formation is greater than the pressure of fracture. There are three ways to reduce the density of cement slurries: exterders water additives, microspheres and foamed slurries. The most used extender water additive is sodium bentonite, which is a clay with a good capacity of water absorption and expansion of its volume, the main disadvantage of this additive is the reduction of the strength. Currently, the use of nanoscale particles has received special attention, mainly because they get new functionalities. Following this trend, this paper aims to use a colloidal solution of nano-silica as an exterders water additives for use in oil wells. Slurries were designed with fixed 13lb/gal density and concentration of nano silica 0.1 gpc; 0.4 gpc; 0.7 and 1gpc, the influence of nano-silica was studied at these levels in isolation and combined varying concentrations of CaCl2,. Tests including rheology, stability, strength, thickening time, porosity and permeability. Besides the API tests, microstructural characterizations were performed after 28 days of the slurries, X-ray diffraction (XRD) and scanning electron microscopy (SEM)

Uso de argilominerais e diatomita como adsorvente de fenóis em águas produzidas na indústria de petróleo

The oil production in Brazil has been increasing each year. Consequently, increasing volumes of water produced are generated with large quantities of contaminants, which brings many problems in disposing of these waters. The concern that the concentrations of contaminants in water produced meet existing laws for disposal of effluents, has been extremely important for the development of different techniques for treatment of water produced. The study of clay minerals as adsorbents of organic contaminants has grown considerably so in order to combine the low cost with the efficiency of environmental preservation and health issues. Thus, this study aims to understand the characteristics of vermiculite clay, sodium bentonite, calcium bentonite and diatomite and evaluate their performance as adsorbents for phenol in the water produced. Through adsorption isotherms it was possible to observe the behavior of these adsorptive clay and diatomite for adsorption of phenol, the main phenolic compound found in water produced. Different concentrations of synthetic solutions of phenol were put in touch with these adsorbents under same conditions of agitation and temperature. The adsorbents were composted adsorptive favorable, but the vermiculite and diatomite showed little capacity for absorption, being suggested for absorbs small concentrations of phenol in the balance isothermal

Estudo da modificação de bentonita para a remoção de fenol em águas produzidas na indústria de petróleo

This study evaluates the inclusion of quaternary ammonium salt, bromide hexadecyl trimethyl ammonium (HDTMA-Br) on sodium bentonite to evaluate their performance on the adsorption of phenol present in produced water. It was observed an increase in d001 samples modified with HDTMA-Br by diffraction of X-rays, showing the intercalation of quaternary ammonium cations in the interlamellar layers of clay. Through the adsorption isotherms could be abserver adsorption behavior of sodium bentonite and organophilic bentonite produced in three different concentrations of HDTMA-Br for adsorption of phenol, which is the main phenolic compound found in the product water. Different concentrations of synthetic solutions of phenol were placed in contact with these adsorbents under the same conditions of agitation and temperature. The adsorbent showed adsorptive favorable, especially the clay modified with the highest concentration of HDTMA-Br, 150% CEC of clay, BEN30-14, with higher amounts of phenol adsorbed per gram of adsorbent (mg.g-1)

Utilização de nanosílica como aditivo estendedor para pastas cimentantes de baixa densidade destinadas à cimentação de poços petrolíferos

Cementing operations are conducted at different times of the well s life and they have high importance, because the functions are fundamental to keep good properties during a long life of the well, such as, maintain the mechanical stability of the well, to promote the isolation hydraulic and support the tubing. In some situations, the rocky zones have low fractures pressures and require the use of lightweight slurries to prevent the hydrostatic pressure in the formation is greater than the pressure of fracture. There are three ways to reduce the density of cement slurries: exterders water additives, microspheres and foamed slurries. The most used extender water additive is sodium bentonite, which is a clay with a good capacity of water absorption and expansion of its volume, the main disadvantage of this additive is the reduction of the strength. Currently, the use of nanoscale particles has received special attention, mainly because they get new functionalities. Following this trend, this paper aims to use a colloidal solution of nano-silica as an exterders water additives for use in oil wells. Slurries were designed with fixed 13lb/gal density and concentration of nano silica 0.1 gpc; 0.4 gpc; 0.7 and 1gpc, the influence of nano-silica was studied at these levels in isolation and combined varying concentrations of CaCl2,. Tests including rheology, stability, strength, thickening time, porosity and permeability. Besides the API tests, microstructural characterizations were performed after 28 days of the slurries, X-ray diffraction (XRD) and scanning electron microscopy (SEM)

Uso de argilominerais e diatomita como adsorvente de fenóis em águas produzidas na indústria de petróleo

The oil production in Brazil has been increasing each year. Consequently, increasing volumes of water produced are generated with large quantities of contaminants, which brings many problems in disposing of these waters. The concern that the concentrations of contaminants in water produced meet existing laws for disposal of effluents, has been extremely important for the development of different techniques for treatment of water produced. The study of clay minerals as adsorbents of organic contaminants has grown considerably so in order to combine the low cost with the efficiency of environmental preservation and health issues. Thus, this study aims to understand the characteristics of vermiculite clay, sodium bentonite, calcium bentonite and diatomite and evaluate their performance as adsorbents for phenol in the water produced. Through adsorption isotherms it was possible to observe the behavior of these adsorptive clay and diatomite for adsorption of phenol, the main phenolic compound found in water produced. Different concentrations of synthetic solutions of phenol were put in touch with these adsorbents under same conditions of agitation and temperature. The adsorbents were composted adsorptive favorable, but the vermiculite and diatomite showed little capacity for absorption, being suggested for absorbs small concentrations of phenol in the balance isothermal

Estudo de titanatos nanoestruturados obtidos por tratamento hidrotérmico de óxido de titânio em meio alcalino

TiTanate NanoTubes (TTNT) were synthesized by hydrothermal alkali treatment of TiO2 anatase followed by repeated washings with distinct degrees of proton exchange. TTNT samples with different sodium contents were characterized, as synthesized and after heattreatment (200-800ºC), by X-ray diffraction, scanning and transmission electron microscopy, electron diffraction, thermal analysis, nitrogen adsorption and spectroscopic techniques like FTIR and UV-Vis diffuse reflectance. It was demonstrated that TTNTs consist of trititanate structure with general formula NaxH2−xTi3O7·nH2O, retaining interlayer water in its multiwalled structure. The removal of sodium reduces the amount of water and contracts the interlayer space leading, combined with other factors, to increased specific surface area and mesopore volume. TTNTs are mesoporous materials with two main contributions: pores smaller than 10 nm due to the inner volume of nanotubes and larger pores within 5-60 nm attributed to the interparticles space. Chemical composition and crystal structure of TTNTs do not depend on the average crystal size of the precursor TiO2-anatase, but this parameter affects significantly the morphology and textural properties of the nanostructured product. Such dependence has been rationalized using a dissolution-recrystallization mechanism, which takes into account the dissolution rate of the starting anatase and its influence on the relative rates of growth and curving of intermediate nanosheets. The thermal stability of TTNT is defined by the sodium content and in a lower extent by the crystallinity of the starting anatase. It has been demonstrated that after losing interlayer water within the range 100-200ºC, TTNT transforms, at least partially, into an intermediate hexatitanate NaxH2−xTi6O13 still retaining the nanotubular morphology. Further thermal transformation of the nanostructured tri- and hexatitanates occurs at higher or lower temperature and follows different routes depending on the sodium content in the structure. At high sodium load (water washed samples) they sinter and grow towards bigger crystals of Na2Ti3O7 and Na2Ti6O13 in the form of rods and ribbons. In contrast, protonated TTNTs evolve to nanotubes of TiO2(B), which easily convert to anatase nanorods above 400ºC. Besides hydroxyls and Lewis acidity typical of titanium oxides, TTNTs show a small contribution of protonic acidity capable of coordinating with pyridine at 150ºC, which is lost after calcination and conversion into anatase. The isoeletric point of TTNTs was measured within the range 2.5-4.0, indicating behavior of a weak acid. Despite displaying semiconductor characteristics exhibiting typical absorption in the UV-Vis spectrum with estimated bandgap energy slightly higher than that of its TiO2 precursor, TTNTs showed very low performance in the photocatalytic degradation of cationic and anionic dyes. It was concluded that the basic reason resides in its layered titanate structure, which in comparison with the TiO2 form would be more prone to the so undesired electron-hole pair recombination, thus inhibiting the photooxidation reactions. After calcination of the protonated TTNT into anatase nanorods, the photocatalytic activity improved but not to the same level as that exhibited by its precursor anatase

Trissoralen um medicamento de baixa dosagem: estudos termoanalíticos da compatibilidade do fármaco-excipientes e determinação de parâmetros de qualidade para cápsulas magistrais

The trioxsalen (Tri) is a low-dose drug used in the treatment of psoriasis and other skin diseases. The aim of the study was applying the thermal analysis and complementary techniques for characterization, evaluation of the trioxsalen stability and components of manipulated pharmaceutical formulations. The thermal behavior of the Tri by TG/DTG-DTA in dynamic atmosphere of synthetic air and nitrogen showed the same profile with a melting peak followed by a volatilization-related event. From the curves TG / DTG is observed a single stage of mass loss. By heating the drug in the stove at temperatures of 80, 240 and 260 °C, it had no change in chemical structure through the techniques of XRD, HPLC, MIR, OM and SEM. From the non-isothermal and isothermal TG kinetic studies was possible to calculate the activation energy and reaction order for the Tri. The drug showed good thermal stability. Studies on drug-excipient compatibility showed interaction of trissoralen with sodium lauryl sulfate 1:1. There was no interaction with aerosol, pregelatinized starch, sodium starch glycolate, cellulose, croscarmellose sodium, magnesium stearate, lactose and mannitol.The characterization of three trioxsalen formulations at concentrations of 2.5, 5, 7.5, 10, 12.5 and 15 mg was performed by DSC, TG / DTG, XRD, NIR and MIR. The PCA classification method based on spectral data from the NIR and MIR of trissoralen formulations allows successful differentiation into three groups. The formulation 3 was the one that best showed analytical profile with the following composition of aerosil excipients, pre-gelatinized starch and cellulose. The activation energy of the volatilization process of the drug was determined in binary mixtures and formulation 3 through fitting and isoconversional methods. The binary mixture with sodium starch glycolate and lactose showed differences in kinetic parameters compared to the drug isolated. The thermoanalytical techniques (DSC and TG / DTG) were shown to be promising methodologies for quantifying trioxsalen obtained by the linearity, selectivity, no use solvents, without sample preparation, speed and practicality.