Caracterização da resistência do algodoeiro a Ramularia areola e variabilidade molecular do patógeno

This research was conducted with the aim to study the genetic and pathogenic structure of Ramularia areola isolates collected in Brazil and to characterize the resistance response in cotton plants to ramularia spot. The genetic variability of 28 isolates of R. areola was studied using RAPD markers. The pathogenicity evaluation was realized by the inoculation of 6 isolates on cotton varieties Guazuncho-2 (Gossypium hirsutum) and VH8-4602 (Gossypium barbadense). The inheritance of disease resistance was studied using an artificially inoculated population of F2 individuals derived from the intercross of Guazuncho-2 (susceptible variety) end VH8-4602 (resistant variety), and also the parents and F1 individuals. Molecular polymorphism between the G. hisutum varieties DeltaOpal (suscetible) and CNPA CO-11612 (resistant) was estimated by 118 SSR and 24 AFLP markers. The parental genotypes Guazuncho-2 and VH8-4602 were selected for mapping, and then Recombinant Inbred Lines (RIL´s) derived from this crossing were evaluated with SSR 12 markers. The analysis of population structure of R. areola revealed that the three subpopulations were genetically simillar (Gst=0.18), and the isolates from Goiás and Minas Gerais were more similar to each other (0,92). This probability can be related to the relatively high gene flow among the three subpopulations (Nm=2.20). The isolates R. areola 9.1, from Minas Gerais State and 8.1 and 8.3 from Goiás State were the most aggressive ones to the susceptible variety Guazuncho-2. The variety VH8-4602 presented high level of resistance to ramularia spot. No differential interaction was observed between the pathogens and the analyzed varieties, and the resistance was classified as horizontal. The quantification of disease by number of necrotic lesions and number of spores in individual plants of F1 and F2 generations from the crossing between the varieties Guazuncho-2 and VH8-4602 presented continuous distribution, suggesting polygenic resistance. The resistance is probabilly recessive, since necrotic lesions and sporulation were observed on F1 plants. The molecular polymorphism between DeltaOpal e CNPA CO-11612 lineages was low (6%), then would be difficult to accomplish molecular mapping of disease resistance using this intercross. With the genotyping of the RIL s it was verified that 25% of the markers segregated in the proportions proposed by Mendel s Law and 75% of the studied markers presented segregation distortion in favor to the parental G. hirsutum. Both the low genetic variability of the pathogen and the number of resistance genes suggest that durable genetic resitance may be achieved

Índices de obesidade central e fatores de risco cardiovascular na síndrome dos ovários policísticos

Fundamento: A obesidade abdominal apresenta elevada prevalência em mulheres com síndrome dos ovários policísticos (SOP) e está associada a um aumento do risco cardiovascular. Objetivo: Verificar a acurácia da circunferência da cintura (CC), da relação cintura-quadril (RCQ), da relação cinturaestatura (RCEST) e do índice de conicidade (índice C), no que se refere à detecção de fatores de risco cardiovascular (FRCV) em mulheres com SOP. Métodos: Por meio de estudo transversal, foram alocadas 102 mulheres (26,5 ± 5 anos) com diagnóstico de SOP, de acordo com o consenso de Rotterdam. O colesterol total (CT), os triglicerídeos (TG), o LDL-colesterol (LDL-C), o HDLcolesterol (HDL-C), a glicemia de jejum, a glicemia após teste oral de tolerância à glicose (TOTG) e a pressão arterial (PA) foram avaliados em todas as pacientes, além das variáveis antropométricas. Resultados: A relação cintura-estatura foi o marcador que apresentou correlações positivas significativas com o maior número de FRCV (PA, TG e glicemia após TOTG), destacando-se ainda a correlação negativa com HDL-C. Todos os marcadores antropométricos avaliados se correlacionaram positivamente com PA, enquanto CC e RCQ apresentaram correlação positiva também com TG. No tocante à acurácia para detecção de FRCV, os indicadores antropométricos considerados apresentaram taxas de sensibilidade superiores a 60%, com destaque para a RCEST, que apresentou sensibilidade superior a 70%. Conclusão: A RCEST demonstrou ser o indicador antropométrico com a melhor acurácia para a predição de FRCV. Nesse sentido, propõe-se a inclusão desse parâmetro de fácil mensuração na avaliação clínica para o rastreamento de mulheres com SOP e FRCV----------------------ABSTRACT Background: Women with polycystic ovary syndrome (PCOS) present a high prevalence of abdominal obesity, which is associated with an increased cardiovascular risk. Objective: To verify the accuracy of the waist circumference (WC), waist-to-hip ratio (WHR), waist-to-height ratio (WHtR) and the conicity index (CI) in the detection of cardiovascular risk factors (CVRF) in women with PCOS. Methods: The present transversal study allocated 102 women (26.5 ± 5 years) with a diagnosis of PCOS, according to the Rotterdam criteria. Total cholesterol (TC), triglycerides (TG), LDL-cholesterol (LDL-C), HDL-cholesterol (HDL-C), fasting glucose, glucose after the oral glucose tolerance test (OGTT) and blood pressure (BP) were evaluated in all patients, in addition to the anthropometric variables. Results: The WHtR was the marker that presented significant positive correlations with the highest number of CVRF (BP, TG and post-OGTT glucose), whereas there was a negative correlation with HDL-C. All the evaluated anthropometric markers were positively correlated with BP, whereas WC and WHR also presented a positive correlation with TG. Regarding the accuracy for the detection of CVRF, the anthropometric markers presented a sensibility > 60%, especially the WHtR, which had a sensibility > 70%. Conclusion: The WHtR showed to be the most accurate anthropometric indicator for the prediction of CVRF. In this sense, we propose the inclusion of this easily-measured parameter in the clinical assessment for the screening of women with PCOS and CVRF

Resposta de Chromobacterium Violaceum cultivada em alta concentração de ferro

The Chromobacterium violaceum is a β-proteobacterium Gram-negative widely found in tropical and subtropical regions, whose genome was sequenced in 2003 showing great metabolic versatility and biotechnological and pharmaceutical potential. Given the large number of ORFs related to iron metabolism described in the genome of C. violaceum, the importance of this metal for various biological processes and due to lack of data about the consequences of excess of iron in free-living organisms, it is important to study the response mechanism of this bacterium in a culture filled with iron. Previous work showed that C. violaceum is resistant to high concentrations of this metal, but has not yet been described the mechanism which is used to this survival. Thus, to elucidate the response of C. violaceum cultured in high concentrations of iron and expecting to obtain candidate genes for use in bioremediation processes, this study used a shotgun proteomics approach and systems biology to assess the response of C. violaceum grown in the presence and absence of 9 mM of iron. The analysis identified 531 proteins, being 71 exclusively expressed by the bacteria grown in the presence of the metal and 100 just in the control condition. The increase in expression of proteins related to the TCA cycle possibly represents a metabolic reprogramming of the bacteria caused by high concentration of iron in the medium. Moreover, we observed an increase in the activity assay of superoxide dismutase and catalase as well as in Total Antioxidant Activity assay, suggesting that the metal is inducing oxidative stress in C. violaceum that increases the levels of violacein and antioxidant enzymes to better adapt to the emerging conditions. Are also part of the adaptive response changes in expression of proteins related to transport, including iron, as well as an increased expression of proteins related to chemotaxis response, which would lead the bacteria to change the direction of its movement away from the metal. Systems Biology results, also suggest a metabolic reprogramming with mechanisms coordinated by bottleneck proteins involved in transcription (GreA), energy metabolism (Rpe and TpiA) and methylation (AhcY)

Análise proteômica de Chromobacterium violaceum: acúmulo estacionário e diferencial após exposição à luz UVC

Chromobacterium violaceum is a free-living bacillus, Gram-negative commonly found in water and sand of tropical and subtropical regions. One of its main characteristic it's the ability to produce the purple pigment named violacein, that shows countless biological activities. In 2003, the genome of this organism was totally sequenced and revealed important informations about the physiology of this bacteria. However, few post-genomics studies had been accomplished. This work evaluated the protein profile of C. violaceum cultivated in LB medium at 28ºC that allowed the identification and characterization of proteins related to a possible secretion system that wasn't identified and characterized yet in C. violaceum, to the quorum sensing system, to regulatory process of transcription and translation, stress adaptation and biotechnological potential. Moreover, the response of the bacteria to UVC radiation was evaluated. The comparison of the protein profile, analyzed through 2-D electrophoresis, of the control group versus the treatment group allowed the identification of 52 proteins that arose after stress induction. The obtained results enable the elaboration of a stress response pathway in C. violaceum generated by the UVC light. This pathway, that seems to be a general stress response, involves the expression of proteins related to cellular division, purine and pirimidine metabolism, heat chock or chaperones, energy supply, regulation of biofilm formation, transport, regulation of lytic cycle of bacteriophages, besides proteins that show undefined function. Despite the response present similarities with the classic SOS response of E. coli, we still cannot assert that C. violaceum shows a SOS-like response, mainly due to the absence of characterization of a LexA-like protein in this organism

Proteômica diferencial da Chromobacterium violaceum em resposta ao estresse oxidativo induzido por peróxido de hidrogênio

The β-proteobacterium Chromobacterium violaceum is a Gram-negative, free-living, saprophytic and opportunistic pathogen that inhabits tropical and subtropical ecosystems among them, in soil and water of the Amazon. It has great biotechnological potential, and because of this potential, its genome was completely sequenced in 2003. Genome analysis showed that this bacterium has several genes with functions related to the ability to survive under different kinds of environmental stresses. In order to understand the physiological response of C. violaceum under oxidative stress, we applied the tool of shotgun proteomics. Thus, colonies of C. violaceum ATCC 12472 were grown in the presence and absence of 8 mM H2O2 for two hours, total proteins were extracted from bacteria, subjected to SDS-PAGE, stained and hydrolysed. The tryptic peptides generated were subjected to a linear-liquid chromatography (LC) followed by mass spectrometer (LTQ-XL-Orbitrap) to obtain quantitative and qualitative data. A shotgun proteomics allows to compare directly in complex samples, differential expression of proteins and found that in C. Violaceum, 131 proteins are expressed exclusively in the control condition, 177 proteins began to be expressed under oxidative stress and 1175 proteins have expression in both conditions. The results showed that, under the condition of oxidative stress, this bacterium changes its metabolism by increasing the expression of proteins capable of combating oxidative stress and decreasing the expression of proteins related processes bacterial growth and catabolism (transcription, translation, carbon metabolism and fatty acids). A tool with of proteomics as an approach of integrative biology provided an overview of the metabolic pathways involved in the response of C. violaceum to oxidative stress, as well as significantly amplified understanding physiological response to environmental stress. Biochemical and "in silico" assays with the hypothetical ORF CV_0868 found that this is part of an operon. Phylogenetic analysis of superoxide dismutase, protein belonging to the operon also showed that the gene is duplicated in genome of C. violaceum and the second copy was acquired through a horizontal transfer event. Possibly, not only the SOD gene but also all genes comprising this operon were obtained in the same manner. It was concluded that C. violaceum has complex, efficient and versatile mechanisms in oxidative stress response

Transcriptoma diferencial entre células-tronco mesenquimais humanas jovens e senescentes

Human mesenchymal stem cells (MSC) are powerful sources for cell therapy in regenerative medicine. The long time cultivation can result in replicative senescence or can be related to the emergence of chromosomal alterations responsible for the acquisition of tumorigenesis features in vitro. In this study, for the first time, the expression profile of MSC with a paracentric chromosomal inversion (MSC/inv) was compared to normal karyotype (MSC/n) in early and late passages. Furthermore, we compared the transcriptome of each MSC in early passages with late passages. MSC used in this study were obtained from the umbilical vein of three donors, two MSC/n and one MSC/inv. After their cryopreservation, they have been expanded in vitro until reached senescence. Total RNA was extracted using the RNeasy mini kit (Qiagen) and marked with the GeneChip ® 3 IVT Express Kit (Affymetrix Inc.). Subsequently, the fragmented aRNA was hybridized on the microarranjo Affymetrix Human Genome U133 Plus 2.0 arrays (Affymetrix Inc.). The statistical analysis of differential gene expression was performed between groups MSC by the Partek Genomic Suite software, version 6.4 (Partek Inc.). Was considered statistically significant differences in expression to p-value Bonferroni correction ˂.01. Only signals with fold change ˃ 3.0 were included in the list of differentially expressed. Differences in gene expression data obtained from microarrays were confirmed by Real Time RT-PCR. For the interpretation of biological expression data were used: IPA (Ingenuity Systems) for analysis enrichment functions, the STRING 9.0 for construction of network interactions; Cytoscape 2.8 to the network visualization and analysis bottlenecks with the aid of the GraphPad Prism 5.0 software. BiNGO Cytoscape pluggin was used to access overrepresentation of Gene Ontology categories in Biological Networks. The comparison between senescent and young at each group of MSC has shown that there is a difference in the expression parttern, being higher in the senescent MSC/inv group. The results also showed difference in expression profiles between the MSC/inv versus MSC/n, being greater when they are senescent. New networks were identified for genes related to the response of two of MSC over cultivation time. Were also identified genes that can coordinate functional categories over represented at networks, such as CXCL12, SFRP1, xvi EGF, SPP1, MMP1 e THBS1. The biological interpretation of these data suggests that the population of MSC/inv has different constitutional characteristics, related to their potential for differentiation, proliferation and response to stimuli, responsible for a distinct process of replicative senescence in MSC/inv compared to MSC/n. The genes identified in this study are candidates for biomarkers of cellular senescence in MSC, but their functional relevance in this process should be evaluated in additional in vitro and/or in vivo assays

Desenvolvimento de formulações para produção de grés porcelanato a partir de matérias-primas da região da bacia do Parnaíba

Brazil is a great ceramic raw materials productor because of the its big number of clay deposits, in various areas of the ceramic industry. Although, the majority of the natural reservations are unknown or not studied yet, so there is no scientific technical dates that can guide their usage and industrial application, as well as the racional and optimazed way of usage by the industrial sector. The state of Maranhão has a gigant mineral wealth as esmectite, bentonite, kaolin, clays, feldspates, marine salt, iron and others, but produce only products with small agregated value compared to the porcelanato, one of the most expensives ceramic cover tiles, the reason for that is the low water absorption (lower than 0,5%), beside present amazing tecnicals features, like mechanical resistence. The main objective of the work is to do the characterization of four clays, with the finallity of find an application by the results and develop formulations to produce porcelanato using these raw materials from Timon-MA. For this were made the raw materials characterization using X ray fluorecence; X ray diffraction; Differencial thermal analysis; Dilatometric analysis and Tecnological properties, planing three formulations that were sinterized at six different temperatures: 1150, 1170, 1190, 1210, 1230 and 1250ºC for 7 minutes. After the sinteratization, the samples were submitted to tension resistance analysis. Were attained two formulations with the requested properties to produce porcelanato

Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration

O efeito do tratamento da atapulgita no desenvolvimento de compósito com o polietileno reciclado

The study aimed at the treatment of attapulgite for the development and characterization of composite recycled low density polyethylene - PEBD_rec embedded with natural attapulgite - ATP_NAT, sifted - ATP_PN and attapulgite treated with sulfuric acid - ATP_TR in different compositions (1, 3 and 5%) and compared with the PEBD_rec. The atapulgitas, natural, screened and treated, were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and determining the area specific surface (BET). The composites were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), Xray diffraction (XRD), torque rheometry, scanning electron microscopy (SEM) and traction. The composite PEBD_rec / ATP (natural, sieved and treated) were produced by mixing in the molten state in a single screw extruder matrix wire with subsequent reprocessing matrix tape. It was found that the screening of attapulgite not reduce the quantity of quartz and the acid treatment completely extracted dolomite aggregate impurities of the channels attapulgite, and increase their surface area. The addition of attapulgite in PEBD_rec acts as a catalyst, reducing the thermal stability of the polymer. The increased concentration of attapulgite, increases resistance and reduces the elongation at break and modulus of elasticity of the composite PEBD_rec / attapulgite

Tratamentos de fibras de carnaúba [copernicia prunífera (miller) h. e. moore] para o desenvolvimento de compósito biodegradável com matriz de polihidroxibutirato

The use of raw materials from renewable sources for production of materials has been the subject of several studies and researches, because of its potential to substitute petrochemical-based materials. The addition of natural fibers to polymers represents an alternative in the partial or total replacement of glass fibers in composites. In this work, carnauba leaf fibers were used in the production of biodegradable composites with polyhydroxybutyrate (PHB) matrix. To improve the interfacial properties fiber / matrix were studied four chemical treatments to the fibers..The effect of the different chemical treatments on the morphological, physical, chemical and mechanical properties of the fibers and composites were investigated by scanning electron microscopy (SEM), infrared spectroscopy, X-ray diffraction, tensile and flexural tests, dynamic mechanical analysis (DMA), thermogravimetry (TGA) and diferential scanning calorimetry (DSC). The results of tensile tests indicated an increase in tensile strength of the composites after the chemical treatment of the fibers, with best results for the hydrogen peroxide treated fibers, even though the tensile strength of fibers was slightly reduced. This suggests a better interaction fiber/matrix which was also observed by SEM fractographs. The glass transition temperature (Tg) was reduced for all composites compared to the pure polymer which can be attributed to the absorption of solvents, moisture and other low molecular weight molecules by the fibers

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Incorporação de resíduo cerâmico para prevenção da retrogressão da resistência de cimentos de poços de petróleo submetidos à injeção de vapor

Steam injection is the most used thermal recovery method of oil nowadays because of the high degree of development of the technique that allows high recovery factors. However, injection of superheated steam into the reservoir affects the entire structure of the well, including the cemented layer that presents a retrogression of compressive strength and increases the permeability due to formation of more crystalline and denser phases at temperatures above 110 °C. These changes result in failures in the cement that favor the entrance of formation fluids into the annulus space resulting in unsafe operations and restrictions in the economic life of the well. But the strength retrogression can be prevented by partial replacement of cement by silica-based materials that reduce the CaO/SiO2 ratio of cement slurries changing the trajectory of the reactions, converting those deleterious phases in phases with satisfactory mechanical strength and permeability. The aim of this study was to evaluate the behavior of a ceramic waste material rich in silica in partial and total substitution of a mineral additive used to fight the strength retrogression of cement slurries subjected to high temperatures. The evaluation was made by compression, X-ray diffraction (XRD) and thermogravimetry (TG/DTG). The samples were submitted to a cycle of low temperature (38 °C) for 28 days and a cycle of low temperature followed by exposure to 280 ºC and 1000 psi by 3 days. The results showed that slurries with additions of up to 30% of the waste material are not enough to prevent the strength retrogression, while slurries with additions of the waste material combined with silica flour in various proportions produced hydrated products of low Ca/Si ratios that maintained the compressive strength at satisfactory levels

Avaliação da corrosão em dutos por técnica gravimétrica e de resistência elétrica

With the increasing of demand for natural gas and the consequent growth of the pipeline networks, besides the importance of transport and transfer of oil products by pipeline, and when it comes to product quality and integrity of the pipeline there is an important role regarding to the monitoring internal corrosion of the pipe. This study aims to assess corrosion in three pipeline that operate with different products, using gravimetric techniques and electrical resistance. Chemical analysis of residues originated in the pipeline helps to identify the mechanism corrosive process. The internal monitoring of the corrosion in the pipelines was carried out between 2009 and 2010 using coupon weight loss and electrical resistance probe. Physico-chemical techniques of diffraction and fluorescence X-rays were used to characterize the products of corrosion of the pipelines. The corrosion rate by weight loss was analyzed for every pipeline, only those ones that has revealed corrosive attack were analyzed located corrosion rate. The corrosion potential was classified as low to pipeline gas and ranged from low to severe for oil pipelines and the pipeline derivatives. Corrosion products were identified as iron carbonate, iron oxide and iron sulfide

Efeito da adição de cargas minerais leves na resistência mecânica de grautes para cimentação de poços offshore

The preparation of cement slurries for offshore well cementing involves mixing all solid components to be added to the mixing water on the platform. The aim of this work was to study the formulation of pre-prepared dry mixtures, or grouts, for offshore oilwell cementing. The addition of mineral fillers in the strength of lightweight grouts applied for depths down to 400 m under water depths of 500 m was investigated. Lightweight materials and fine aggregates were selected. For the choice of starting materials, a study of the pozzolanic activity of low-cost fillers such as porcelain tile residue, microsilica and diatomaceous earth was carried out by X-ray diffraction and mechanical strength tests. Hardened grouts containing porcelain tile residue and microsilica depicted high strength at early ages. Based on such preliminary investigation, a study of the mechanical strength of grouts with density 1.74 g/cm3 (14.5 lb/gal) cured initially at 27 °C was performed using cement, microsilica, porcelain tile residue and an anti-foaming agent. The results showed that the mixture containing 7% of porcelain tile residue and 7% of microsilica was the one with the highest compressive strength after curing for 24 hours. This composition was chosen to be studied and adapted for offshore conditions based on testes performed at 4 °C. The grout containing cement, 7% of porcelain tile residue, 7% of active silica and admixtures (CaCl2), anti-foaming and dispersant resulted satisfactory rheology and mechanical strength after curing for 24 hours of curing

Resistência da artéria carótida e autônima funcional em mulheres idosas

High carotid artery resistance indices in the elderly arise mainly as a result of harmful daily lifestyle behavior and poor eating habits. The aim of this multidisciplinary study was to assess and correlate carotid artery resistance and functional autonomy in elderly women. A descriptive, exploratory cross-sectional study was conducted with a sample comprising 27 women, enrolled in pastoral programs in the city of Teresina, Brazil. Carotid artery resistance was assessed by a high-resolution Doppler ultrasound device and functional autonomy was evaluated through five protocol tests of the Latin American Development Group for the Elderly (GDLAM), simulating activities of daily life. The data were analyzed by the Shapiro-Wilk test and the correlation by Spearman s test, considering a p-value of <0.05. The sample consisted of women with mean age and standard deviation of (68.67 ± 4.52) years, respectively and carotid resistance index of (0.71 ± 0.07). The general index value of functional autonomy classified the elderly of the study group as weak in the performance of activities of daily living (30.46 ± 6.31). The general index of functional autonomy showed a high level of sedentary behavior in the group studied (p < 0.01). The sample was classified as weak in the performance of activities of daily life. The correlation coefficient between the carotid resistance index and the general GDLAM index was r = 0.998 and p = 0.000, showing a significant correlation. The elderly women assessed had a high carotid artery resistance index and low functional autonomy; a positive correlation was found between the dependent variables studied. To perform this study we formed a team composed of a nurse, who helped in organizing the sample and performing the examinations; a radiologist, who conducted the Doppler examinations; an angiologist, who collaborated in interpreting examination data; in addition to two physical education professors and two physical therapists, who applied the functional autonomy tests and conducted the 34 research along elderly health lines, contributing thus to the multidisciplinary character, fundamental for carrying out the study