Efeitos da perda de peso induzida pela cirurgia bariátrica sobre a função respiratória

Background: Obesity leads to alteration of lung volumes and capacities due to accumulation of fat in the chest wall and abdomen. Few studies have shown that weight loss induced by surgery improves lung function. Our objective was to evaluate the anthropometric development, pulmonary function, respiratory muscle, strength and endurance after weight loss induced by bariatric surgery. Methods: We evaluated in pre and post operative period variables of weight, BMI, NC, WHR and spirometric and respiratory pressure. Results: 39 subjects were evaluated, with age mean 35.9 ± 10.9 years, predominantly by women (76.3%). The weight mean decreased from 124.8 ± 17.5 kg to 88.8 ± 14.28 kg in post operative. The mean BMI ranged from 47,9 ± 5,6 Kg/m² to 34,3 ± 4,75 Kg/m². There was a significant increase in FVC from 3,63 ± 0,94 to 4,01±1,03, FEV1 from 3,03 ± 0,72 to 3,39 ± 0,85, FEF 25-75% from 3,41 ± 0,72 to 3,82 ± 0,94, PEF from 6,56 ± 1,47 to 7,81 ± 1,69, ERV from 0,35 ± 0,39 to 0,66 ± 0,38, MVV ranged from 103,43 ± 22,21 to 137,27 ± 29,84, all of them to p<0,01. The MIP and MEP showed no significant difference in pre and post operative. It was noted that for every centimeter reduced in neck circumference, an increase of 0.06 in FVC and 5.98 in MVV is observed. This is also observed in weight and BMI. Conclusion: We conclude that weight loss induced by bariatric surgery in obese provides a significant improvement in lung function and reduction of fat around the neck is more important in the generation of lung volume than the reduction of BMI

Tratamento de cascalho de perfuração utilizando sistemas microemulsionados

The oil industry is one of the activities that generates more waste to the environment. The drill cuttings is a waste generated in large quantities in the drilling process and that may cause environmental damage such as soil contamination and consequently the contamination of groundwater if disposed of without prior treatment. Arises the need to develop scientific activities and research ways to adapt these wastes the current environmental standards. In the case of solid wastes, the NBR 10004: 2004 of the Brazilian Association of Technical Standards (ABNT) classifies them into class I waste (hazardous) and class II (not dangerous), which determines which wastes may or may not be discarded in the environment without causing environmental impact. This study presents a novel alternative for treating drill cuttings, where this waste was classified as class I (Abreu & Souza, 2005), mainly by removing the n-paraffin present in it, since this arises when using drilling fluids base oil. Using microemulsion systems promotes the removal of this contaminant drill cuttings samples from wells located in Alto do Rodrigues - RN. Initially, we determined the concentration of paraffin using infrared method in samples were extracted with ultrasound, we obtained a paraffin concentration in the range from 36.59 to 43.52 g of paraffin per kilogram of cuttings. Used two microemulsion systems containing two nonionic surfactants from different classes, one is an alcohol ethoxylated (UNTL-90) and the other an nonylphenol ethoxylated (RNX 110). The results indicated that the system UNTL-90 surfactant has better efficiency than the system with RNX 110. The study of the influence of contact time at the extraction showed that for times greater than 25 minutes has a tendency to increase the percentage extraction with increasing contact time. It was also observed that the extraction is fast because at 1 minute contact has 22.7% extraction. The reuse of the microemulsion system without removing the paraffin extracted in previous steps, showed reduction of 29.32 in percentage of extraction by comparing the first and third extraction, but by comparing the first and second extractions reduction is 8.5 in percentage extraction, so the systems reuse optimization can be an option for economically viable removing paraffin from cuttings. The extraction with shaking is more effective in the treatment of cuttings, reaching the extraction percentage of 87.04%, that is, obtaining a drill cuttings with 0.551% paraffin. Using the percentage of paraffin employed in non-aqueous drilling fluids and fluid maximum limit on cuttings for disposal established by the Environmental Protection Agency of the United States (US EPA), one arrives at the conclusion that the level of paraffin on gravel cannot exceed 3.93%. Conclude that the amount of paraffin in the treated cuttings with the microemulsion system with shaking is below the established by US EPA, showing that the system used was efficient in removing the paraffin from the drill cuttings.