Diagênese e proveniência dos arenitos da tectonossequência Rifte na bacias do Rio do Peixe Araripe, NE do Brasil

This thesis presents diagenetic and provenance studies of sandstones belonging to the Rift Tectonosequence of the Rio do Peixe and Araripe basins. These basins are located in the interior of Northeast Brazil aligned along the Trend-Cariri Potiguar. Their origin is related to the Early Cretaceous rifting event. In terms of lithostratigraphy, the studied section corresponds to the Antenor Navarro, Sousa and Rio Piranhas formations of the Rio do Peixe Basin, and the Missão Velha and Abaiara formations of the Araripe Basin, outcropping in the central-west Cariri Valley. A facies analysis was performed and identified nine distinct sedimentary facies for the Rio de Peixe Basin and ten sedimentary facies for the Araripe Basin, individualized according to the different rock types and their sedimentary structures. These facies associations to led paleoenvironments interpretations and their vertical succession allowed understanding the evolution of the depositional setting during the cronostratigraphic interval studied in these basins. Based on petrographic and diagenetic studies it was possible to characterize the texture and mineralogy of these sandstones, identifying their diagenetic stage and the grain framework provenance. The petrographic study allowed to classify the lithotypes studied in both basins as quartzarenites. Such quartzarenites, in general, are rich in quartz, feldspar and lithic fragment grains, and at accessory levels tourmaline, sphene, zircon, epidote and other mineralogy. The diagenetic history of the studied rocks proved to be very complex, being characterized by a variety mineral of phases that succeeded each other during the eo, meso and telodiagenetic stages. According to the studied formation and the textural and compositional aspects of the rocks, some processes were more or less active, while others were even absent. The eodiagenetic stage is marked by mechanical infiltration of clays and early mechanical compactional processes. The mesodiagenetic phase is characterized by continuity of the mechanical compaction and the beggining of chemical compaction, with quartz and feldspar overgrowths, precipitation of kaolinite, alteration of framework grains to chlorite and illite, and finally, precipitation of opaque minerals. The telodiagenetic stage is represented by the oxidation of some grains, matrix and cements. For the provenance analysis of the studied sandstones were used ternary diagrams whose vertices correspond to the percentage of quartz, feldspar and lithic fragments. This study allowed identifies the source area of these rocks as continental blocks. It was also possible, based on the chemical stability and mineralogical maturity of the rocks, recognize that the Antenor Navarro Formation of the Rio do Peixe Basin, and the upper section of the Missão Velha Formation of Araripe Basin have less maturity and stability when compared with the other studied formations

Evolução diagenética e caracterização dos reservatórios da seção devoniana na Bacia do Rio do Peixe-Nordeste do Brasil

The Rio do Peixe Basin represents a main basin of northeastern Brazil and pioneering work positioned the rocks of this basin in the Early Cretaceous. However, a recent study, based on integrated pollen analysis from three wells, found an unprecedented siliciclastic sedimentary section, in the region, of early Devonian age. Therefore, the present study aims a detailed petrographic and petrological analysis of this devonian section, in the Rio do Peixe Basin and proposes a diagenetic evolution, to understand the characteristics of the porous system, identify the main reservoir petrofacies with the main factors impacting on the quality of these rocks as reservoirs and a quick study on the provenance of this section. The petrographic study was based on samples obtained from subsurface and surface. The diagenetic evolution of petrofacies and its identification were based only on subsurface samples and the study of provenance was based on surface samples. The thin sections were prepared from sandstones, pelites and sandstones intercalated with pelites. The original detrital composition for this section is arcosean and the main diagenetic processes that affected these rocks occur in various depths and different conditions, which resulted in extensive diagenetic variety. The following processes were identified: early fracture and healing of grains; albitization of K-feldspar and plagioclase; siderite; precipitation of silica and feldspar; mechanical infiltration of clay and its transformation to illite/esmectite and illite; autigenesis of analcime; dissolution; autigenesis of chlorite; dolomite/ferrous dolomite/anquerite; apatite; calcite; pyrite; titanium minerals and iron oxide-hidroxide. The occurrence of a recently discovered volcanism, in the Rio do Peixe Basin, may have influenced the diagenetic evolution of this section. Three diagenetic stages affected the Devonian section: eo, meso and telodiagenesis. This section is compositionally quite feldspathic, indicating provenance from continental blocks, between transitional continental and uplift of the basement. From this study, we observed a wide heterogeneity in the role of the studied sandstones as reservoirs. Seven petrofacies were identified, taking into account the main diagenetic constituent responsible for the reduction of porosity. It is possible that the loss of original porosity was influenced by intense diagenesis in these rocks, where the main constituent for the loss of porosity are clays minerals, oxides and carbonate cement (calcite and dolomite)

Caracterização de minerais pesados ao longo do Rio Piranhas-Açu/RN distribuição e proveniência

This dissertation deals with the characterization, distribution and provenience of heavy minerals along the Piranhas-Açu River, from the City of Parelhas (Seridó River) to your mouth at the City of Macau-RN. Many heavy minerals species were recorded in this study: clinoamphibole, epidote (including zoisite), garnet, sillimanite, tourmaline, staurolite, andalusite, zircon, rutile, augite, ilmenite, hematite and magnetite. Major transparent minerals, those forming more than 5% of some assemblages, are hornblende, epidote, tourmaline, staurolite and zircon. Predominant opaque mineral is ilmenite. Six assemblages were identified along the river: (i) Garnet-hornblende-tourmaline with sillimanite, when cutting rocks of the Seridó Formation; (ii) Hornblende-garnet-zircon, when crossing rocks of the Caicó gnaisse-migmatitic Complex; (iii) Hornblende-zircon-epidote-staurolite, when draining rocks of the Jucurutu Formation; (iv) Hornblende-zircon-epidote, when cutting rocks of the Açu Formation; (v) Hornblende-zircon-staurolite, on the lowermost Açu River, when crossing limestones of the Jandaíra Formation and (vi) Zircon-tourmaline-staurolite in the Açu River mouth (Cenozoic rocks) where coastal process dominate. Mineral ratios that reflect differences in grain shape, density, and selective chemical decomposition were used in an attempt to isolate the effects of source and process as controls of mineral variability. Reworking of the sediments was regionally effective in selective sorting; the more equant minerals (e.g. epidote) and heavier minerals (e.g. opaques) had a higher probability of being selected for permanent deposition during reworking. The processes of selective decomposition stand out at the river mouth. A priori knowledge of provenance, associated with the assemblage distribution and effects of process were utilized to the interpretations, that points to the follow provenances: hornblende comes from micashists of the Seridó Formation, orthognaisses and amphibolites of the Caico Complex, paragnaisses and paranphibolites of the Jucurutu Formation and granites intrusions; epidote comes from paragnaisses and calciosilicatics of the Jucurutu Formation, granites intrusions (-Npy3al/ca and -Npy3mz, gravels deposits and Açu Formation; Andalusite and staurolite come from the Seridó Formation; Sillimanite, tourmaline and garnet come from micashists of the Seridó Formation, as well as from quartzites of the Equador Formation; Zircon comes from Precambrian rocks (pink and prismatic zircon) and from sediments of several cycles (round zircon); Opaques come from all rocks cutted for the Piranhas-Açu River; Rutile comes from metamorphic rocks, in general; Augite comes from the Ceará-Mirim, Serra do Cuó and Macau volcanisms. The texture of gravels deposits reveals a sediment transport mechanisms by traction-current processes, together with a diagenetic clay matrix suggests a hot-humid environments for deposition. The presence of unstable heavy minerals assemblages, as well as pebbles of different composition and degrees of rounding and esfericity, indicate more than one source. The occurrence of calcio/alkaline granites suites, in areas closed to the gravel deposits, suggests that these intrusions are the main source of sediments. This could explain for instance, the significant amounts of epidote and presence of unstable heavy minerals (e.g. hornblende). The analyses of heavy minerals also show significante variability between the modern (Piranhas-Açu) and ancestral (Açu Formation) river sediments. In general, these variations reflect relatively higher unstable and lower stable heavy minerals contents of the modern Piranhas-Açu sediments. The absence of significant compositional differences probably reflects uniform weathering conditions

Mapeamento da zona costeria protegida por arenitos de praia (Beachrocks) em Nísia Floresta - RN

The goal of this work comprises the detailed mapping of the coastal zone of the south coast of the State of Rio Grande do Norte. The emphasis of the study is the units of beachrocks and the features of the physical environment associated. The mapping of the beachrocks and of the adjacent coastal features is justified, among other aspects, by the fact that the beachrocks constitute an important protection agent against the sea erosion. By one side, they dissipate the energy of the sea waves and make possible the imprisonment of sediments in the foreshore. The beachrocks in the studied area are constituted of discontinuous strips, parallel to the coast line presenting emerged in some places, even in the highest tides, entirely submerged or partially buried by coastal sediments. These sandstones compose the landscape of big part of the coast and they are responsible for the partial dissipation of the energy of the waves on the studied coast. The methodology used in this work consisted of different techniques were used, as the use of aerial pictures of small format (FAPEFs), acquisition of data of system of global positioning (GPS) and later elaboration of thematic maps and of digital models of soil (MDTs). The results obtained in the mapping of the use and occupation of the soil, demonstrate the existence of strong human pressure in the coastal area (built lots and no built), occupying about 54,74% of built areas. This problem has been taking to degradation risks due to the inconsequent expansion of divisions into lots and tourist enterprises. The MDT came as an excellent resource, as visual as functional, being possible to visualize several angles and to act in three dimensions the relief of the area in study, as well as to identify the present features in the coastal area. By the importance of the bodies of beachrocks as a protection agent against the coastal erosion, faces were delimited in the sandstones based in geometric criteria, classifying them in, central face, outside face, inside face, break and undermiming. These last two associates to the erosion and washout in the base of these bodies. Field data indicate clearly that the most important process in the fracturing of the bodies is associated with mechanisms related to the gravity, being the joints formed by processes of gravitational sliding. Finally, the mapping of the coastal zone starting from aerial pictures of small format it made possible the identification of the elements that compose the beach strip, for accomplishing with larger detailed level and by presenting a better monitoring of the dynamics of the coastal zone

Isótopos de Nd na proveniência de rochas e sedimentos da bacia potiguar, ne do Brasil

Nd ISOTOPES IN THE PROVENANCE OF TERRIGENOUS AND CARBONATE ROCKS AND SEDIMENTS OF THE POTIGUAR BASIN, NORTHEASTERN BRAZIL. Mesozoic and Cenozoic rocks from the Potiguar Basin, including terrigenous and carbonate sediments have been investigated to identify their isotopic signature and source areas. Additionally, this study aims to determine the provenance of terrigenous and carbonate sediments on the Brazilian Continental shelf adjacent to Potiguar Basin. The Sm-Nd isotopic signatures of the rocks yielded model ages (TDM) in the range of 2,19- 2,88 Ga, indicating archean to paleoproterozoic sources from the basement. The terrigenous sediments yielded model ages (TDM) in the range of 2,31-2,26 Ga, from 17,5 to 0 cm depth. Despite the small number of samples, limited variations of provenance ages indicates the homogenization of the sediments, probably due to the strong influence of the basement, as the main source of sediments to the shelf. The Sm-Nd isotopic signatures of the carbonate sediments yielded model ages (TDM) in the range of 2,09-2,61 Ga, indicating archean to paleoproterozoic sources from the basement. The results also indicate that the shelf sediments are mainly derived from the Açu River or other small rivers from the Setentrional Sector of Rio Grande do Norte State. The littoral drift doesn´t seem to contribute with sediments from the Oriental Sector since isotopic signatures from this sector were not detected.

Pirometamorfismo nos arenitos da Formação Açu, Bacia Potiguar, NE do Brasil

Pyrometamorphism results from conditions of high temperatures and very low pressures provoked by the intrusion of hypabyssal basic bodies into sedimentary or metassedimentary hosting rocks. The onshore portion of the Potiguar Basin in NE Brazil offers examples of this type of metamorphism nearby the contacts of Paleogene to Neogene plugs, sills and dikes of diabases and basalts crosscutting sandstones, siltstones and shales of the Açu Formation (Albian-Cenomanian). The thermal effects over these rocks are reflected on textures and minerals assemblages that characterize the sanidinite facies of metamorphism, often with partial melting of the feldspathic and mica-rich matrix. The liquid formed is potassic and peraluminous, with variably colored rhyolitic glass (colorless, yellow, brown) comprising microcrystals of tridymite, sanidine and clinoenstatite, besides residual detrital clasts of quartz and rarely zircon, staurolite and garnet. Lenses of shale intercalated within the sandstones display crystallites of Fe-cordierite (sekaninaite), mullite, sanidine, armalcolite (Fe-Ti oxide) and brown spinel. The rocks formed due to the thermal effect of the intrusions are called buchites for which two types are herein described: a light one derived from feldspathic sandstone and siltstone protoliths; and a dark one derived from black shale protoliths. Textures indicating partial melting and minerals such as sanidine, mullite, tridymite and armalcolite strongly demonstrate that during the intrusion of the basic bodies the temperature reached 1,000-1,150°C, and was followed by quenching. Cooling of the interstitial melts has as consequences the closure of pores and decrease of the permeability of the protolith, which varies from about 17-11% in the unaffected rocks to zero in the thermally modified types. Although observed only at contacts and over small distances, the number of basic intrusions hosted within the Potiguar Basin in both onshore and offshore portions leaves opened the possibility of important implications of the thermal effects over the hydrocarbon exploration in this area as well in other Cretaceous and Paleozoic basins in Brazil

Estudo da influência de sistemas microemulsionados na molhabilidade de arenitos e na recuperação avançada de petróleo

Sandstone-type reservoir rocks are commonly responsible for oil accumulation. The wettability is an important parameter for the physical properties of the container, since it interferes in characteristics such as relative permeability to the aqueous phase, residual oil distribution in the reservoir, operating characteristics with waterflood and recovery of crude oil. This study applied different types of microemulsion systems - MES - in sandstone reservoirs and evaluated their influences on wettability and residual oil recovery. For this purpose, four microemulsion were prepared by changing the nature of ionic surfactants (ionic and nonionic). Microemulsions could then be characterized by surface tension analysis, density, particle diameter and viscosity in the temperature range 30° C to 70° C. The studied oil was described as light and the sandstone rock was derived from the Botucatu formation. The study of the influence of microemulsion systems on sandstone wettability was performed by contact angle measurements using as parameters the rock treatment time with the MES and the time after the brine surface contact by checking the angle variation behavior. In the study results, the rock was initially wettable to oil and had its wettability changed to mixed wettability after treatment with MES, obtaining preference for water. Regarding rock-MES contact time, it was observed that the rock wettability changed more when the contact time between the surface and the microemulsion systems was longer. It was also noted only a significant reduction for the first 5 minutes of interaction between the treated surface and brine. The synthesized anionic surfactant, commercial cationic, commercial anionic and commercial nonionic microemulsion systems presented the best results, respectively. With regard to enhanced oil recovery performance, all systems showed a significant percentage of recovered oil, with the anionic systems presenting the best results. A percentage of 80% recovery was reached, confirming the wettability study results, which pointed the influence of this property on the interaction of fluids and reservoir rock, and the ability of microemulsion systems to perform enhanced oil recovery in sandstone reservoirs.

Estudo da influência de sistemas microemulsionados na molhabilidade de arenitos e na recuperação avançada de petróleo

Sandstone-type reservoir rocks are commonly responsible for oil accumulation. The wettability is an important parameter for the physical properties of the container, since it interferes in characteristics such as relative permeability to the aqueous phase, residual oil distribution in the reservoir, operating characteristics with waterflood and recovery of crude oil. This study applied different types of microemulsion systems - MES - in sandstone reservoirs and evaluated their influences on wettability and residual oil recovery. For this purpose, four microemulsion were prepared by changing the nature of ionic surfactants (ionic and nonionic). Microemulsions could then be characterized by surface tension analysis, density, particle diameter and viscosity in the temperature range 30° C to 70° C. The studied oil was described as light and the sandstone rock was derived from the Botucatu formation. The study of the influence of microemulsion systems on sandstone wettability was performed by contact angle measurements using as parameters the rock treatment time with the MES and the time after the brine surface contact by checking the angle variation behavior. In the study results, the rock was initially wettable to oil and had its wettability changed to mixed wettability after treatment with MES, obtaining preference for water. Regarding rock-MES contact time, it was observed that the rock wettability changed more when the contact time between the surface and the microemulsion systems was longer. It was also noted only a significant reduction for the first 5 minutes of interaction between the treated surface and brine. The synthesized anionic surfactant, commercial cationic, commercial anionic and commercial nonionic microemulsion systems presented the best results, respectively. With regard to enhanced oil recovery performance, all systems showed a significant percentage of recovered oil, with the anionic systems presenting the best results. A percentage of 80% recovery was reached, confirming the wettability study results, which pointed the influence of this property on the interaction of fluids and reservoir rock, and the ability of microemulsion systems to perform enhanced oil recovery in sandstone reservoirs.

Evolução diagenética e caracterização dos reservatórios da seção devoniana na Bacia do Rio do Peixe-Nordeste do Brasil

The Rio do Peixe Basin represents a main basin of northeastern Brazil and pioneering work positioned the rocks of this basin in the Early Cretaceous. However, a recent study, based on integrated pollen analysis from three wells, found an unprecedented siliciclastic sedimentary section, in the region, of early Devonian age. Therefore, the present study aims a detailed petrographic and petrological analysis of this devonian section, in the Rio do Peixe Basin and proposes a diagenetic evolution, to understand the characteristics of the porous system, identify the main reservoir petrofacies with the main factors impacting on the quality of these rocks as reservoirs and a quick study on the provenance of this section. The petrographic study was based on samples obtained from subsurface and surface. The diagenetic evolution of petrofacies and its identification were based only on subsurface samples and the study of provenance was based on surface samples. The thin sections were prepared from sandstones, pelites and sandstones intercalated with pelites. The original detrital composition for this section is arcosean and the main diagenetic processes that affected these rocks occur in various depths and different conditions, which resulted in extensive diagenetic variety. The following processes were identified: early fracture and healing of grains; albitization of K-feldspar and plagioclase; siderite; precipitation of silica and feldspar; mechanical infiltration of clay and its transformation to illite/esmectite and illite; autigenesis of analcime; dissolution; autigenesis of chlorite; dolomite/ferrous dolomite/anquerite; apatite; calcite; pyrite; titanium minerals and iron oxide-hidroxide. The occurrence of a recently discovered volcanism, in the Rio do Peixe Basin, may have influenced the diagenetic evolution of this section. Three diagenetic stages affected the Devonian section: eo, meso and telodiagenesis. This section is compositionally quite feldspathic, indicating provenance from continental blocks, between transitional continental and uplift of the basement. From this study, we observed a wide heterogeneity in the role of the studied sandstones as reservoirs. Seven petrofacies were identified, taking into account the main diagenetic constituent responsible for the reduction of porosity. It is possible that the loss of original porosity was influenced by intense diagenesis in these rocks, where the main constituent for the loss of porosity are clays minerals, oxides and carbonate cement (calcite and dolomite)

Caracterização batimétrica e fisicooceanográfica do canal de acesso ao porto de Cabedelo/PB: uma análise ambiental ao derrame de óleo

The State of Paraíba is one of the most dynamic states of Brazil, strategically located in the northeast, is notable for the excellent potential for integration of different transportation modes forming the states of Rio Grande do Norte, Pernambuco and Alagoas. The dynamic that occurs with port activity causes changes in the space where it is installed. And the elements of this space are always more than suffering direct or indirect influences as the flow in the port is expanded. Therefore, this region became subject to the accidental spillage of oil, because it presents a heavy traffic of ships of various sizes that can run aground or collide with oil causing accidental events. The study of geomorphological and sedimentological compositions of seafloor becomes important as more is known about the relationships between these parameters and associated fauna, and can identify their preferred habitats. The database background, acoustically collected along the proposed study area, is a wealth of information, which were duly examined, cataloged and made available. Such information can serve as an important tool, providing a geomorphological survey of the sedimentary area studied, and come to subsidize, in a flexible, future decision making. With the study area Port of Cabedelo, Paraíba - Brazil, this research aimed to evaluate the influence of the tidal surface and background in modeling the seabed, including the acquisition of information about the location of submerged rocky bodies and the depth of these bodies may turn out to be natural traps for the trapping of oil in case of leaks, and obtain the relationship between types of bed and the hydrodynamic conditions present in the region. In this context, for this study were collected bathymetric data (depth) and physical oceanographic (height of water column, water temperature, intensity and direction of currents, waves and turbidity), meteorological (rainfall, air temperature, humidity, winds and barometric pressure) of the access channel to the Port of Cabedelo / PB and its basin evolution (where the cruise ships dock), and includes tools of remote sensing (Landsat 7 ETM +, 2001), so that images and the results are integrated into Geographic Information Systems and used in the elaboration of measures aimed at environmental protection areas under the influence of this scale facilities, serving as a grant to prepare a contingency plan in case of oil spills in the region. The main findings highlight the techniques of using hydroacoustic data acquisition together bathymetric surveys of high and low frequency. From there, five were prepared in bathymetric pattern of Directorate of Hydrography and Navigation - DHN, with the depth in meters, on a scale of 1:2500 (Channel and Basin Evolution of Access to Port of Cabedelo), where there is a large extent possible beachrocks that hinder the movement of vessels in the port area, which can cause collisions, running aground and leaking oil. From the scatter diagram of the vectors of currents, it can be seen as the tidal stream and undergoes a channeling effect caused by the bidirectional effect of the tide (ebb and flood) in the basin of the Port of Cabedelo evolution in NW-direction SE and the highest speed of the currents occurs at low tide. The characterization weather for the period from 28/02 to 04/07/2010 values was within the expected average for the region of study. The multidisciplinary integration of products (digital maps and remote sensing images), proved to be efficient for the characterization of underwater geomorphological study area, reaching the aim to discriminate and enhance submerged structures, previously not visible in the images

Aplicação de sistemas microemulsionados ácidos em acidificação de poços

Stimulation operations have with main objective restore or improve the productivity or injectivity rate in wells. Acidizing is one of the most important operations of well stimulation, consist in inject acid solutions in the formation under fracture formation pressure. Acidizing have like main purpose remove near wellbore damage, caused by drilling or workover operations, can be use in sandstones and in carbonate formations. A critical step in acidizing operation is the control of acid-formation reaction. The high kinetic rate of this reaction, promotes the consumed of the acid in region near well, causing that the acid treatment not achive the desired distance. In this way, the damage zone can not be bypassed. The main objective of this work was obtain stable systems resistant to the different conditions found in field application, evaluate the kinetic of calcite dissolution in microemulsion systems and simulate the injection of this systems by performing experiments in plugs. The systems were obtained from two non ionic surfactants, Unitol L90 and Renex 110, with sec-butanol and n-butanol like cosurfactants. The oily component of the microemlsion was xilene and kerosene. The acqueous component was a solution of HCl 15-26,1%. The results shown that the microemulsion systems obtained were stable to temperature until 100ºC, high calcium concentrations, salinity until 35000 ppm and HCl concentrations until 25%. The time for calcite dissolution in microemulsion media was 14 times slower than in aqueous HCl 15%. The simulation in plugs showed that microemulsion systems promote a distributed flux and promoted longer channels. The permeability enhancement was between 177 - 890%. The results showed that the microemulsion systems obtained have potential to be applied in matrix acidizing

Aplicação de microemulsões na solubilização de frações pesadas de petróleo

This work presents studies related to the use of microemulsions in the solubilization of heavy crude oil fractions responsible by the formation of deposits. The first stage of the work was addressed to the construction of phases diagrams, with the intention of determining the area within which the microemulsion is formed. The following systems were studied: UNITOL L 90 n-Butanol - Water - Kerosene (system 1); UNITOL L 90 - n-Butanol - Water - Xylene (system 2); UNITOL L 90 n-Butanol - Water - Kerosene/Xylene 10% (system 3); UNITOL L 90 - Sec-Butanol - Water - Xylene (system 4). In parallel experiments of physical adsorption were carried out by the static method, with the intention of simulating natural conditions of reservoirs. Crude oil of the Fazenda Belém field (Rio Grande do Norte), was used as solute, xylene as solvent and the Assu sandstone (Rio Grande do Norte, Brazil) and Botucatu sandstone (Paraná, Brazil) as rock reservoirs. The curves of adsorption presented the S format type, in agreement with the classification proposed by Giles, Smith and Huitson (1974). The solubilization process was accomplished in the batch method, by varying the time of agitation, the microemulsions and the solid/solution ratio. The experiments showed that the microemulsions presented high efficiency in the solubilization of the crude oil adsorbed on the sandstones. System 2 presented an efficiency of 99% for the Assu sandstone and 97% for the Botucatu sandstone

Desenvolvimento de sistemas de pastas leves para aplicação em cimentação de poços petrolíferos com baixo gradiente de fratura

All around the world, naturally occurring hydrocarbon deposits, consisting of oil and gas contained within rocks called reservoir rocks , generally sandstone or carbonate exists. These deposits are in varying conditions of pressure and depth from a few hundred to several thousand meters. In general, shallow reservoirs have greater tendency to fracture, since they have low fracture gradient, ie fractures are formed even with relatively low hydrostatic columns of fluid. These low fracture gradient areas are particularly common in onshore areas, like the Rio Grande do Norte basin. During a well drilling, one of the most favorable phases for the occurrence of fractures is during cementing, since the cement slurry used can have greater densities than the maximum allowed by the rock structure. Furthermore, in areas which are already naturally fractured, the use of regular cement slurries causes fluid loss into the formation, which may give rise to failures cementations and formation damages. Commercially, there are alternatives to the development of lightweight cement slurries, but these fail either because of their enormous cost, or because the cement properties were not good enough for most general applications, being restricted to each transaction for which the cement paste was made, or both reasons. In this work a statistical design was made to determine the influence of three variables, defined as the calcium chloride concentration, vermiculite concentration and nanosilica concentration in the various properties of the cement. The use of vermiculite, a low density ore present in large amounts in northeastern Brazil, as extensor for cementing slurries, enabled the production of stable cements, with high water/cement ratio, excellent rheological properties and low densities, which were set at 12.5 lb / gal, despite the fact that lower densities could be achieved. It is also seen that the calcium chloride is very useful as gelling and thickening agent, and their use in combination with nanosilica has a great effect on gel strength of the cement. Hydrothermal Stability studies showed that the pastes were stable in these conditions, and mechanical resistance tests showed values of the order of up to 10 MPa

Estudo de sistemas microemulsionados utilizando água do mar na recuperação avançada de petróleo

Petroleum exists in the nature in certain underground formations where it is adsorbed into the rocks pores. For the conventional recovery methods usually only 30% of the oil is extracted and this can be credited, basically, to three aspects: high viscosity of the oil, geology of the formation and high interfacial tensions between the reservoir s fluids. The enhanced recovery methods use the injection of a fluid or fluids mixture in a reservoir to act in points where the conventional process didn't reach the recovery rates. Microemulsion flooding, considered an enhanced method, has the purpose to desorb the oil from the rock formation and to attain an efficient displacement of the oil emulsion. With this in mind, this work was accomplished with two main objectives: the study of the parameters effect that influence a microemulsified system (surfactant and cosurfactant types, C/S rate and salinity) and the evaluation of displacement efficiency with the microemulsions that showed stability in the rich aqueous area. For the analyzed parameters it was chose the microemulsions composition used in the recovery stage: 25% water, 5% kerosene, 46.7% of butanol as cosurfactant and 23.3% of BC or SCO cosurfactant. The core plugs of Assu and Botucatu sandstones were appraised in porosity and permeability tests and then submitted to the steps of saturation with seawater and oil, conventional recovery with water and enhanced recovery with the selected microemulsions. The Botucatu sandstone presented better recovery parameters, and the microemulsion composed with BS surfactant had larger recovery efficiency (26.88%)

Influência da acrilamida e da poliacrilamida em sistema microemulsionado visando aplicação na recuperação avançada de petróleo

This work aims to study the influence of two additives, the monomer, acrylamide and its polymer, polyacrylamide, solubilized in microemulsion systems and applied on enhanced oil recovery. By the microemulsion system obtained, it was chosen points into the phase diagram, presenting these compositions: 25%, 30%, 35% C/T; 2% Fo (fixed for all points) e 73%, 68% e 63% Fa, respectively. However, the monomer and the polymer were solubilized in these microemulsion points with 0.1%; 0.5%; 1% e 2% of concentration, ordering to check the concentration influence at the physicochemical properties (surface tension and rheology) of the microemulsion. Through the salinity study, was possible to observe that the concentrations of 1% and 2% of polymer made the solution became blurred, accordingly, the study of surface tension and rheology only was made for the concentrations of 0.1% e 0.5% of monomer and polymer, respectively. By the surface tension study it was observed that how the concentration of active matter (C/T) was increasing the surface tension was amending for each system, with or without additives. In the rheology study, as it increases the concentration of active matter increases both the viscosity of the microemulsion system (SME) with no additive, as the SME with polymer (AD2). After the entire study, it was chosen the lower point of active matter (25% C/T; 2% Fo e 73% Fa), plus additives in concentrations of 0.1% and 0.5% to be used on enhanced oil recovery. Assays were made on sandstone from Botucatu Formation, where after the tests, it was concluded that among the studied points, the point who showed the best efficiency of advanced shift was the microemulsion system + 0.5% AD2, with a recovery of 28% of oil in place and a total of 96,49%, while the other solution with 0.5% of polymer presented the worst result, with 14.1% of oil in place and 67,39% of efficiency of total displacement