Efeitos da terapia laser de baixa intensidade associada ao exercício aeróbio no reparo de tenotomia do tendão de aquiles de ratos diabéticos

Diabetes Mellitus (DM ) is a complex disease that requires continuous medical care for the reduction of risk factors in addition to glycemic control. The typical hyperglycemia of this disease produces glycosylation of proteins and so the consequence is the accumulation of glycosylation final products in various human tissues, among them, the tendon. The aerobic exercise (AE) and the low level laser therapy (LLLT) have been used to treat tendinopathies in individuals with or without DM. Objective: The aim of this study was to watch the effect of the LLLT and the AE, in association, in partial tenotomy of the tissue repair of the Achilles tendon (AT) of diabetic rats. Methods: 91 animals were utilized and divided in to the following groups: control group (GC), injured control group (GCL), diabetic group (GD), diabetic group LLLT (GD – TLBI), diabetic group trained (GD - EX) and diabetic group trained laser (GD-EX+TLBI). The animals were submitted to intervention with AE, using a protocol with a progressive increase of time (12 to 60 min) and speed of (4 to 9 m/min), and the LLLT (660 nm laser, 10mW, 4 J/cm², single point for 16 seconds, three times for week). It was analyzed morphological, biomechanical and molecular characteristics. For data showing normal distribution was used one-way ANOVA test and post hoc Tukey and data without normal distribution was used Mann Whitney test and post hoc Dunn's. It was accepted p <0.05 for statistical significance Results: The biomechanical tests indicated major improvement in the GC and GD-EX+TLBI groups when compared with the diabetic groups in the following variables: maximum load, strain, absorbed energy, stress, cross section area, elastic modulus and energy density (p<0.05). The analysis through molecular biology indicated that the association of aerobic exercise and LLLT generated an increase of the collagen I gene expression and modulated the expression of the MMP2 and MMP9 (p<0.05). No observed any major improvement in the morphological variable studied. Conclusion: the LLLT associated with aerobic exercise promotes and increase of the mechanical properties, in the control of collagen I gene expression and of the MMP2 and MMP9 of the diabetic rats.

Ateliês de história e pedagogia da matemática: contribuições para a formação de professores que ensinam matemática nos anos iniciais

This paper presents a discussion about the use of the History of Mathematics as an educational resource and conceptual mediator in the formation of teachers who teach mathematics in the years of elementary school. It was a qualitative action method, in order to show the importance of holding workshops of History and Pedagogy of Mathematics as contribution to overcome the conceptual difficulties of teaching and teachers regarding the content covered in the course of education and afterwards they have to teach in the early of elementary school. We assume that understanding the historical, social and cultural comprehension as a conceptual and didactic focus effectively nurture the pursuit of a teaching and learning of mathematics students safe and justified in order to contribute to overcoming the difficulties of teaching and learning usually occurred in the classroom of the early years. In this sense, we organized a study group formed by students of Bachelors in Education and Mathematics at the University of Piauí. We developed five training workshops in History and Pedagogy of Mathematics, with a workload of 20 hours each and four follow-up sessions and advicement, totalizing 180 hours. The purpose of workshops was to develop studies on the History of Mathematics that could support the formation of a conceptual and didactic group with a view to prepare teaching materials and activities based on information drawn from undertaken historical studies .The products designed were used in formation of the group itself and will later be used in training teachers of public school in Teresina, in the form of workshop of History and Pedagogy of Mathematics in order to overcome problems arising from teaching and conceptual this education degree in Education Based on the obtained informations it was possible to suggest new referrals procedural level of education and university extension that may contribute to the reorientation of initial and continuing training of teachers in the early years elementary school

Desenvolvimento de um núcleo versátil e integrado de ferramentas CAD/CAE para a modelagem e simulação de peças mecânicas

Currently there is still a high demand for quality control in manufacturing processes of mechanical parts. This keeps alive the need for the inspection activity of final products ranging from dimensional analysis to chemical composition of products. Usually this task may be done through various nondestructive and destructive methods that ensure the integrity of the parts. The result generated by these modern inspection tools ends up not being able to geometrically define the real damage and, therefore, cannot be properly displayed on a computing environment screen. Virtual 3D visualization may help identify damage that would hardly be detected by any other methods. One may find some commercial softwares that seek to address the stages of a design and simulation of mechanical parts in order to predict possible damages trying to diminish potential undesirable events. However, the challenge of developing softwares capable of integrating the various design activities, product inspection, results of non-destructive testing as well as the simulation of damage still needs the attention of researchers. This was the motivation to conduct a methodological study for implementation of a versatile CAD/CAE computer kernel capable of helping programmers in developing softwares applied to the activities of design and simulation of mechanics parts under stress. In this research it is presented interesting results obtained from the use of the developed kernel showing that it was successfully applied to case studies of design including parts presenting specific geometries, namely: mechanical prostheses, heat exchangers and piping of oil and gas. Finally, the conclusions regarding the experience of merging CAD and CAE theories to develop the kernel, so as to result in a tool adaptable to various applications of the metalworking industry are presented

Jambolão (Syzygium cumini) desidratado por liofilização e secagem em leito de jorro: avaliação do impacto do processo de secagem e caracterização do potencial funcional do produto final

Tropical fruits have been extensively studied due to their functional potential attributed to the presence of natural bioactive compounds. The exotic fruit jambolan (Syzygium cumini) has been reported for its appreciable amount of phenolic compounds, especially anthocyanins and antioxidant capacity. Nevertheless, there are hardly any derived jambolan products in the Brazilian market. In addition to that, considerable volumes of fruit are lost due to their high perishability. Dried fruits have become an important fruit market segment due to its weight and volume reduction and decreased transportation and storage costs. Thus, this study evaluated the jambolan pulp submitted to spouted bed drying (JLJ) and lyophilization (JLI), besides assessing the drying impact on the final product. In order to achieve this, the process performance was calculated and compared, as well the physicochemical and bioactive characteristics (moisture, water activity (aw), solubility, hygroscopicity, density, color, structure through images obtained by scanning electron microscopy (SEM), concentration of bioactive (total phenolic compounds (TPC), anthocyanins, proanthocyanidins and ascorbic acid) and antioxidant activity. The results showed drying efficiency higher than 60% for both products and that JLJ group showed higher moisture and water activity when compared to the JLI group (p<0.05). The two types of drying were able to produce stable final product in the microbiological point of view, given that both showed aw < 0.6. The final products exhibited high solubility (73.7 to 81.6%) and low hygroscopicity (9.8 to 11.6%), desirable characteristics for dehydrated foods. Despite the losses caused by drying, the dried jambolan pulp by both methods showed high TPC (468.6 to 534.0 mg GAE/100g dm), anthocyanins (from 491.9 to 673.4 mg. eq. cyanidin-3-glicoside/100g dm), proanthocyanidins (66.9 to 76.6 mg QTE/g dm) and ascorbic acid (156.4 to 186.8 mg/100 g dm). Taken together, the results of this study reveal spouted dried and freeze dried jambolan pulp as bioactive-rich natural products with suitable physicochemical and functional characteristics to be used as food ingredients. The data also demonstrate the drying techniques as rational strategies for the exploitation of the exotic fruit jambolan

Suco desidratado de caju (Anacardium occidentale L.) por atomização: caracterização físico-química, bioativa e estudo da vida de prateleira do produto

Despite the relatively organized cashew (Anacardium occidentale L.) productive chain and the number of cashew derivatives found in the market, it is estimated that over 90% of the cashew peduncle is wasted. A possible strategy for a better commercial exploitation of this agroindustrial commodity would be the production of spray dried cashew pulp. Thus, this paper approaches the yellow cashew pulp spray drying process and the final product evaluation. Based on that, the shelf life of the spray dried cashew pulp packed in different packaging was evaluated. Drying was conducted in two drying temperatures (140 °C to 150 °C) and two concentrations of Arabic gum (AG, 15% and 25%), which summed four experimental groups. The drying performance was evaluated as well as the physicochemical characteristics (moisture, water activity, total soluble solids, pH, density, solubility, particle diameter, hygroscopicity, degree of caking, color, scanning electronic microscopy and X-ray diffraction), composition (protein, ash, fat and sugars) and bioactive and functional value (total phenolic compounds, carotenoids, ascorbic acid and antioxidant activity) of the final products. Results showed spray drying efficiency higher than 65% for all experiments, mainly for the C4 group (150 °C and 25% AG) which reached efficiency of 93.4%. It was also observed high solubility (94.7% to 97.9%) and the groups with lower hygroscopicity (5.8% and 6.5%) were those with the highest proportion of drying coadjuvant. The particle diameters ranged between 14.7 μm and 30.2 μm and increased with the proportion of AG. When comparing the product before and after spray drying, the drying impact was evident. However, despite the observed losses, dried yellow cashew showed high phenolic concentration (from 235.9 to 380.4 mg GAE eq / 100 g DM), carotenoids between 0.22 and 0.49 mg/100 g DM and remarkable ascorbic acid levels (852.4 to 1346.2 mg/100 g DM), in addition to antioxidant activity ranging from 12.9 to 16.4 μmol TE/ g DM. The shelf life study revealed decreased phenolic content over time associated to a slight water activity increase. Overall, our results unveil the technological and bioactive potential of dried yellow cashew as a functional ingredient to be used in food formulations or as a ready-to-use product. The technological approach presented here can serve as an efficient strategy for a rational use of the cashew apple, avoiding its current underutilization

Preparação de resinas de poliuretana à base de óleo de mamona e dietanolamina

The aim of this work was the preparation of polyols from reactions between castor oil and dietanolamine to increase the hydroxyl content and the network degree in the products to application in electronic devices. The polyols and the mixtures obtained were characterized by nuclear magnetic ressonance. Castor oil (CO) is a natural triglyceride - based polyol possessing hydroxyl groups, which allow several reactions that produce many different products. Among them are the polyurethanes (PU), which have been considered an ideal product for the covering of electricelectronic circuits, due to their excellent electrical, shock-absorbing, solvents resistance and hydrolytic stability properties. About 90% of the fatty acids present in the castor oil are ricinoleic acid (12-hydroxyoleic acid), while the remaining 10% correspond to non-hydroxylated fatty acids, mainly linoleic and oleic acids. The chemical analysis of castor oil indicates a hydroxyl number of 2.7. In this work, a polyol was obtained by the reaction of the CO with diethanolamine (DEA), in order to elevate the hydroxyl value from 160 to 230 or to 280 mgKOH/g, and characterized by nuclear magnetic resonance (NMR) 1H and 13C (Mercury 200). The polyadition of the resulting polyol with isophorone diisocianate (IPDI) was carried out at 60°C, and the reaction kinetics was followed by rheological measurements in a Haake RS150 rheometer. The electrical properties were determined in a HP LCR Meter 4262A, at 1.0 Hz and 10.0 KHz. The chemical analysis showed that the polyols obtained presented hydroxyl number from 230 to 280 mgKOH/g. The polyadition reaction with IPDI produced polyurethane resins with the following properties: hardness in the range from 45 shore A to 65 shore D (ASTM D2240); a dielectric constant of 3.0, at 25°C (ASTM D150). Those results indicate that the obtained resins present compatible properties to the similar products of fossil origin, which are used nowadays for covering electric-electronic circuits. Therefore, the PUs from castor oil can be considered as alternative materials of renewable source, free from the highly harmful petroleum - derived solvents

Craqueamento termocatalítico de óleo de girassol na presença da peneira molecular SAPO-5

The catalytic cracking of triglycerides presents itself as a possible alternative to the production of biofuels with low emission of pollutants. In this work were synthesized the SAPO-5, the catalysts for the cracking reaction of soybean oil is presented. The solids were powder X-ray diffraction (XRD), thermogravimetric analysis (TG/DTG) and infrared spectroscopy (FTIR). The analyses indicated that the synthesis method has employed to obtain materials with high surface area and high acid. The soybean oil thermal and thermal catalytic cracking, realized from the room temperature to 450 ºC in a simple distillation system, has allowed obtaining two liquid fractions, each consisting of two phases, one aqueous and another organic, organic liquid (OL). The OL obtained from first fractions has shown high acid index, even in the thermal catalytic process. The products obtained in the cracking of soybean oil were analyzed by distillation, acid number, infra-red spectroscopy, density, viscosity, carbon residue, cetane number determination and characterization. The analysis of the products obtained in the presence and in the absence of the SAPO-5 permitted to conclude that all the solids tested presented catalytic activity in the deoxygenation of final products only at the second step of the cracking process

Adsorção dos gases NH3, NO e H2S em fosfato de vanadila, hidrogeno fosfato de vanadila e fosfatos de vanadila dopados por Al, Co, Mn e Cr

In this work were synthesized the materials called vanadyl phosphate, hydrogen vanadyl phosphate and vanadyl phosphate doped by transition metals with the aim in adsorption the following compounds: ammonia, hydrogen sulfide and nitrogen oxide. To characterize the starting compounds was used DRX, FTIR, FRX and TG analysis. After the characterization of substrates, proceeded de adsorption of NH3 and H2S gases in reactor, passing the gases with continuous flow for 30 min and room temperature. Gravimetric data indicate that the matrices of higher performance in adsorption of ammonia was those doped by aluminum and manganese, obtaining results of 216,77 mgNH3/g and 200,40 mgNH3/g of matrix, respectively. The matrice of higher performance in adsorption of hydrogen sulfide was that doped by manganese, obtaining results of 86,94 mgH2S/g of matrix. The synthesis of substrates VOPO4.2H2O and MnVOPO4.2H2O with nitrogen oxide was made in solution, aiming the final products VOPO4.G.nH2O and MnVOPO4.G.nH2O (G = NO and n = number of water molecules). The thermo analytical behavior and the infrared spectroscopy are indicative of formation of VOPO4.2,5NO.3H2O compound. Results of scanning electron microscopy (SEM) and Energy dispersive spectroscopy (EDS) of materials vanadyl phosphate and vanadyl phosphate modified after reaction in solid state or in solution with the gases show morphology changes in substrates, beyond the formation of orthorhombic sulfur crystals over their respective hosts when these adsorb hydrogen sulfide

Integração e interdisciplinaridade no processo ensino/aprendizagem de projeto: o curso de Arquitetura e Urbanismo da Universidade Potiguar de Mossoró-RN

Training in Architecture and Urbanism with its general characteristic involves, in its nature, knowledge of various areas (technology, theory, history, representation, and design), being the space of design conception that place where the synthesis of this knowledge is reflected more clearly. We believe that the integrated work in the architectural curriculum can provide an overview of the project, thus contributing to better training of the architect. This research aims to reflect on the role of integration and interdisciplinary in teaching architectural design. This theme has been work recurrently by critics in the teaching area of project and events of the area as the seminars of the Projetar, highlighted by several authors to search integration as an essential pedagogical approach to design education. The work aims to contribute to reflection and awareness of those involved on the importance of integration in the architectural course of project processes. For this, we analyzed the potential and limits of this process in Architecture and Urbanism Course (CAU) at the Universidade Potiguar (UNP) Mossoró, which has the integration and interdisciplinary recorded since the Pedagogical Project of the Course. This analysis will be performed by observing the development of “interdisciplinary work” in the fifth term during the first half of 2014.1. This research concerns an exploratory qualitative study that aims to investigate specific issues on the teaching/learning architecture project and the integration in architecture courses, following a non-participant observation in architectural design classes in the fifth term of CAU/UnP/ Mossoró, and analysis of final products, which would be the work of the last unit of the semester, called “Interdisciplinary work”. Questionnaires for the teachers who participated in the process has been apply via email and analyzed. Reflection supports several other already carried out to identify the difficulties inherent in applying these principles satisfactorily. Noting, however, that interdisciplinarity, in fact, it goes beyond integration and is even more difficult to achieve. In addition to an educational project that incorporates these principles, such as the course of Architecture and Urbanism of the UNP-Mossoró, full adhesion it is necessary by the faculty and students of this teaching philosophy.

Integração e interdisciplinaridade no processo ensino/aprendizagem de projeto: o curso de Arquitetura e Urbanismo da Universidade Potiguar de Mossoró-RN

Training in Architecture and Urbanism with its general characteristic involves, in its nature, knowledge of various areas (technology, theory, history, representation, and design), being the space of design conception that place where the synthesis of this knowledge is reflected more clearly. We believe that the integrated work in the architectural curriculum can provide an overview of the project, thus contributing to better training of the architect. This research aims to reflect on the role of integration and interdisciplinary in teaching architectural design. This theme has been work recurrently by critics in the teaching area of project and events of the area as the seminars of the Projetar, highlighted by several authors to search integration as an essential pedagogical approach to design education. The work aims to contribute to reflection and awareness of those involved on the importance of integration in the architectural course of project processes. For this, we analyzed the potential and limits of this process in Architecture and Urbanism Course (CAU) at the Universidade Potiguar (UNP) Mossoró, which has the integration and interdisciplinary recorded since the Pedagogical Project of the Course. This analysis will be performed by observing the development of “interdisciplinary work” in the fifth term during the first half of 2014.1. This research concerns an exploratory qualitative study that aims to investigate specific issues on the teaching/learning architecture project and the integration in architecture courses, following a non-participant observation in architectural design classes in the fifth term of CAU/UnP/ Mossoró, and analysis of final products, which would be the work of the last unit of the semester, called “Interdisciplinary work”. Questionnaires for the teachers who participated in the process has been apply via email and analyzed. Reflection supports several other already carried out to identify the difficulties inherent in applying these principles satisfactorily. Noting, however, that interdisciplinarity, in fact, it goes beyond integration and is even more difficult to achieve. In addition to an educational project that incorporates these principles, such as the course of Architecture and Urbanism of the UNP-Mossoró, full adhesion it is necessary by the faculty and students of this teaching philosophy.

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Relações interorganizacionais e confiança no setor da carcinicultura: um estudo de caso na camanor produtos marinhos

This study investigated how the types of confidence based on competence and good will act in the formation and maintenance of cooperation relationships between the Camanor and its partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). It used organizational approaches on networks based primarily on studies of Powell (1987, 1990), Das and Teng (2000, 2001), Child (2001) and Contractor and Lorange (2004) which have described the advantages that cooperative relationships can provide, as well as their limits as alternative governance structures. Confidence has been considered an important factor affecting the actions and development of organizations involved in networks or in strategic alliances (ZAHEER; HARRIS, 2006) and is the most appropriate control mechanism in these situations (SYDOW, 1998). Confidence is seen from two different approaches: the economic and the sociological (ZAHEER; HARRIS, 2006). To facilitate the understanding of confidence some typologies have been created, as proposed by Barney and Hansen (1994), Lane (1998), Das and Teng (2000), Child (2001) and Wever, Martens and Vandenbempt (2005). This study made use of the case study as proposition of Yin (2005). Semi-structured interviews were held with pre-determined routes, in a single stage performed in early 2008. The research subjects were owners and / or responsible for Camanor and its business partners (Aquatec, Purina, Caçuá, Uvifrios and Malta / Cleyton). Also secondary data were collected in several sites related to the industry and enterprises studied, in addition to data collected by previous studies conducted by CARCINEREDES (2006). The primary data were analyzed using the analysing technique of the content proposed by Bardin (1994). Regarding the secondary data, they were qualitatively analyzed according to documentary analysis technique (BARDIN, 1994). Thus, through the data collected, could be concluded that although there is confidence based on good faith in relationships(UZZI, 1998; OF; TENG, 2001), their presence does not determine the formation and / or maintenance of a partnership, serves only in order to facilitate the relationship, making them more flexible. The confidence based on competence (DAS; TENG, 2001) influenced the formation and maintenance of relations studied. Because whether or not to form a relationship with another organization it is used the perception of the partner acts, namely the reputation (image) as decision basis. And it is through the verification of the performance of the partner activities that will determine the continuation of the partnership

Influência dos intermediários de distribuição de produtos turísticos no processo de decisão do meio de hospedagem pelo consumidor

This study examines the complex hotel buyer decision process in front of the tourism distribution channels. Its objective is to describe the influence level of the tourism marketing intermediaries, mainly the travel agents and tour operators, over the hotel decision process by the buyer-tourist. The data collection process was done trough a survey with three hundred brazilian tourists hosted in nineteen hotels of Natal, capital of Rio Grande do Norte, Brazil. The data analysis was done using some multivariate statistic techniques as correlation analysis, multiple regression analysis, factor analysis and multiple discriminant analysis. The research characterizes the hotel services consumers profile and his trip, and identifying the distribution channels used by them. Furthermore, the research verifies the intermediaries influence exercised over hotel buyer decision process, looking for identify causality relations between the influence level and the buyer profile. Verifies that information about hotels available on internet reduces the probability that this influence can be practiced; however it was possible identifying those consumers considers this information complementary and non-substitutes than the information from intermediaries. The characteristics of the data do not allow indentifying the factors that constraint the intermediaries influence neither identifying discriminant functions of the specific distribution channel choice by consumers. The study concludes that consumers don t agree in have been influenced by intermediaries or don t know if they have, still considering important to consult them and internet doesn t substitute their function as information source

Sobre projetos, palavras e imagens: relacionando textos e desenhos nos trabalhos finais de graduação em arquitetura e urbanismo

This research continues the current debate about the role of the images and the words in the architectural design persuasion, where we emphasize the increasing valuation of written documents (FORTY, 2004; MARKUS; CAMERON, 2002), the seduction for the graphical representation (DURAND, 2003) and the rhetorical effects of the graphical and textual resources (TOSTRUP, 1999). Based on these quarrels, we look for verify in the graduate final projects the relation between the design texts and images. From the PROJEDATA, database of the PROJETAR research group (UFRN), we selected the final projects of two brazilians universities, UFRN and USP, that in a first analysis, they had shown as ideal types of two distinct design presentation models, respectively: texts and drawings in separated documents, or combined in an only support. Based on Markus explanation about the function and the content of the texts, on the Durand perspective with regard to graphical representation uses and on Tostrup point of view concerning the rhetorical potential of texts and drawings, we analyze, in a set of 25 projects, how the students relate the textual and imagetical speeches. For this, we related the focus of each speech, in order to verify the possible coherence between both. We conclude that in the model of USP final project the coherence between the texts and the drawings is clearer than in the model adopted in UFRN