Controlador preditivo não linear aplicado ao controle de golfadas em processos de produção de petróleo

Slugging is a well-known slugging phenomenon in multiphase flow, which may cause problems such as vibration in pipeline and high liquid level in the separator. It can be classified according to the place of its occurrence. The most severe, known as slugging in the riser, occurs in the vertical pipe which feeds the platform. Also known as severe slugging, it is capable of causing severe pressure fluctuations in the flow of the process, excessive vibration, flooding in separator tanks, limited production, nonscheduled stop of production, among other negative aspects that motivated the production of this work . A feasible solution to deal with this problem would be to design an effective method for the removal or reduction of the system, a controller. According to the literature, a conventional PID controller did not produce good results due to the high degree of nonlinearity of the process, fueling the development of advanced control techniques. Among these, the model predictive controller (MPC), where the control action results from the solution of an optimization problem, it is robust, can incorporate physical and /or security constraints. The objective of this work is to apply a non-conventional non-linear model predictive control technique to severe slugging, where the amount of liquid mass in the riser is controlled by the production valve and, indirectly, the oscillation of flow and pressure is suppressed, while looking for environmental and economic benefits. The proposed strategy is based on the use of the model linear approximations and repeatedly solving of a quadratic optimization problem, providing solutions that improve at each iteration. In the event where the convergence of this algorithm is satisfied, the predicted values of the process variables are the same as to those obtained by the original nonlinear model, ensuring that the constraints are satisfied for them along the prediction horizon. A mathematical model recently published in the literature, capable of representing characteristics of severe slugging in a real oil well, is used both for simulation and for the project of the proposed controller, whose performance is compared to a linear MPC

Modelo de desdobramento da função qualidade adequado a produção da cerâmica vermelha

A presente dissertação representa uma contribuição na resolução dos problemas que se apresentam no setor das indústrias de cerâmica vermelha, apresentamos um modelo, baseado na estratégia do QFD (Desdobramento da Função Qualidade), na qual associa os requisitos dos consumidores na elaboração dos projetos do produto e dos processos de produção. A qualidade do produto é avaliada tanto no aspecto interno(especificações técnicas) quanto no aspecto externo (qualidades exigidas pelos clientes). A pesquisa mostra, além da realidade que vive o setor das indústrias de cerâmica, a importância e os atributos da qualidade definidos pelos consumidores relativo aos tijolos cerâmicos de vedação. O trabalho também mostra os resultados da aplicação do modelo numa das empresas do setor, através de desdobramentos da qualidade exigida, se estabelece a qualidade planejada, mostra ainda a posição da empresa em relação aos concorrentes em função do desempenho do produto. Procura-se ainda, através de sugestões de melhorias, atacar os problemas das falhas na qual geram o desperdício

Produção de enzimas por fungos em fermentação semi-sólida utilizando bagaço de coco e pedúnculo de caju como substratos

The production of enzymes by microorganisms using organic residues is important and it can be associated with several applications such as food and chemical industries and so on. The objective of this work is the production of CMCase, Xylanase, Avicelase and FPase enzymes by solid state fermentation (SSF) using as substrates: bagasse of coconut and dried cashew stem. The microorganisms employed are Penicillium chrysogenum and an isolated fungus from the coconut bark (Aspergillus fumigatus). Through the factorial design methodology and response surface analysis it was possible to study the influence of the humidity and pH. For Penicillium chrysogenum and the isolated fungus, the coconut bagasse was used as culture medium. In another fermentation, it was used the mixture of coconut bagasse and cashew stem. Fermentations were conducted using only the coconut bagasse as substrate in cultures with Penicillium chrysogenum fungus and the isolated one. A mixture with 50% of coconut and 50% of cashew stem was employed only for Penicillium chrysogenum fungus, the cultivation conditions were: 120 hours at 30 °C in BOD, changing humidity and pH values. In order to check the influence of the variables: humidity and pH, a 2 2 factorial experimental design was developed, and then two factors with two levels for each factor and three repetitions at the central point. The levels of the independent variables used in ascending order (-1, 0, +1), to humidity, 66%, 70.5% and 75% and pH 3, 5 and 7, respectively. The software STATISTICA TM (version 7.0, StatSoft, Inc.) was used to calculate the main effects of the variables and their interactions. The response surface methodology was used to optimize the conditions of the SSF. A chemical and a physic-chemical characterization of the coconut bagasse have determined the composition of cellulose (%) = 39.09; Hemicellulose (%) = 23.80, Total Lignin (%) = 36.22 and Pectin (%) = 1.64. To the characterization of cashew stem, the values were cellulose (g) = 15.91 Hemicellulose (%) = 16.77, Total Lignin (%) = 30.04 and Pectin (%) = 15.24. The results indicate the potential of the materials as substrate for semisolid fermentation enzyme production. The two microorganisms used are presented as good producers of cellulases. The results showed the potential of the fungus in the production of CMCase enzyme, with a maximum of 0.282 UI/mL and the Avicelase enzyme the maximum value ranged from 0.018 to 0.020 UI/ mL, using only coconut bagasse as substrate. The Penicillium chrysogenum fungus has showed the best results for CMCase = 0.294 UI/mL, FPase = 0.058 UI/mL, Avicelase = 0.010 UI/mL and Xylanase = 0.644 UI/ mL enzyme, using coconut bagasse and cashew stem as substrates. The Penicllium chrysogenum fungus showed enzymatic activities using only the coconut as substrate for CMCase = 0.233 UI/mL, FPase = 0.031 to 0.032 UI/ mL, Avicelase = 0.018 to 0.020 UI/mL and Xylanase = 0.735 UI/ mL. Thus, it can be concluded that the used organisms and substrates have offered potential for enzyme production processes in a semi-solid cultivation

Levantamento e avaliação de critérios para a ampliação de escala da produção de biossurfactantes utilizando melaço como substrato

Biosurfactants are amphiphilic molecules synthesized by microorganisms such as bacteria, yeast or filamented fungi cultivated in various carbon sources among sucrose and hydrocarbons. These molecules are composed by a hydrophilic and hydrophobic part. They operate mostly at interfaces of fluids of different polarities. Because of this characteristic, they are potentially employed in numerous industries, such as the textile, medical, cosmetics, food and mainly in the petrochemical ones. Therefore industry has interest in developing new biosurfactant production processes in high scale, in order to become them economically competitive when compared to synthetic biosurfactants. This work aims to evaluate the biosurfactant production applying a non-conventional substrate sugar cane molasses proceeding from the sugar industry thus reducing the production costs. The strain identified as AP029/GLIIA, isolated from oil wells in Rio Grande do Norte state and used in these experiments belongs to the culture collection of Antibiotics Department of UFPE. The fermentation were carried out using different conditions according to a factorial planning 24 with duplicate at center point, in which the studied factors were molasse concentration, nitrate concentration, agitation and aeration ratio. The experiments were performed in a shaker at 38ºC of temperature. Samples were withdrawn in regular periods of time of up to 72 hours of fermentation in order to analyze substrate consumption, cellular concentration, superficial tension, critical micelle dilution (CMD-1 e CMD-2) as well as extracelullar protein production. The results showed a production of 3,480 g/L of biomass, a reduction of 41% on superficial tension, 67% of substrate consumption and 0,2805 g/L of extracellular protein

A convergência digital na produção da notícia: reconfigurações na rotina produtiva dos jornais Tribuna do Norte e Extra

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Publicidade e moda: um estudo sobre a materialidade da mídia e a produção de sentido na revista ffw>>mag!

The proposal of this research is to analyze the convergence between fashion and communication shown on the materiality of the print media, and how the language from the supporter influences on the production of sense by the target market. Made real in the research corpus comprised of six ffw>>mag! magazines from the year 2011. The applied conceptual mechanism tries to investigate the production of sense from the physical attributes before interpreting the message s content, to do so, the Materiality of Communication is used, which offers an investigative apparatus of the media in its material shape, and those as influences in the communicative acts and processes. Methodologically, we adopt the Peircean Semiotics Theory, for its study focus on the analysis of the possible processes of production of sense. Through Semiotics we achieve the interpretative levels that allow us to clarify the questionings that come from the research s objectives, identifying and tracing the cognitive and intelligibility schemes bound to the media speeches of materiality. The analysis coordinated to the concepts and theories employed in this study point to a confirmation that the materiality of the reviewed media communicates to the readers in the same intensity as its content, provides a preview of the content and notifies the intentions of the publication. In the commercial way, characterizing the target audience it craves, and also in the conceptual way, demonstrating the ideas it wants to communicate. Where the convergence between communication and fashion unfolds as the materiality of the media by the choice of the materials and finishing options, and mainly by the selection and manipulation of technical images and colors from the cycles of fashion

O papel da tecnologia cênica e seus desdobramentos para uma economia da produção cultural no nordeste

O papel da tecnologia na produção contemporânea em artes cênicas vem influenciando profundamente as formas de recepção e produção de Teatro, Dança, espetáculos de Circo, shows musicais, entre outras manifestações espetaculares organizadas. Sua aplicação se estende amplamente a outras áreas que necessitam enfatizar o caráter cênico de seus processos de fruição como é o caso dos museus, feiras de ciências, exibições e mostras em artes visuais e o aparato tecnológico de luz, som e configuração espacial usados para estes fins. Neste sentido, o desenvolvimento deste tipo de tecnologia vem gerando e alimentando cadeias produtivas que movimentam uma economia da produção cultural e criam uma rede de relações articuladas em diferentes níveis de atuação, envolvendo produtores de equipamento, fornecedores, lighting designers, cenógrafos, profissionais de sonorização, arquitetos, técnicos de montagem e operação, instituições ensino especializadas, associações de área, entre outros. O foco deste trabalho se concentra em demonstrar como a análise de demandas de tecnologia cênica articuladas pelos sistemas de produção cultural, em particular na região Nordeste do Brasil, possibilitam compreender modelos de organização em curso, contribuindo para o desenvolvimento de uma reflexão multidisciplinar acerca dos processos de produção artística de natureza cênica e como esta produção é afetada pelos limites e possibilidades dos aspectos que caracterizam uma economia destas produções

Otimização da síntese do AlSBA-15 para produção de biodiesel por transesteri-ficação do óleo de coco

Stimulus encouraging the production and consumption of biodiesel favors the policy of pre-serving the environment, contributing to the reduction of greenhouse gas reducing climate change. The current trend of research in this field focuses on improving these processes with the use of heterogeneous catalysts, seeing has significant advantages such as: low contamination of products, ease of separation of the catalyst from the reaction medium, possibili-ty of reuse of the catalyst, decreased corrosion problems. The objective of this research was to optimize the synthesis of AlSBA-15 for the production of biodiesel through transesterification process via ethyl route. For the optimization of hydrothermal synthesis of type AlSBA-15 catalyst has assembled a 23 factorial experimental matrix with eleven trials. The stoichiometric amounts of starting materials were varied according to different ratios Si / Al which is a factor in the experimental design, in addition to the time and temperature of aging of the synthesis gel. The material showed the best results of characterization (SBET = 591.7 (m2 / g), Vp = 0.83 (cm3 / g), Dp = 5.59 (nm), w = 6.48 (nm) was synthesized at 100 ° C for 24 hours, with a ratio Si / Al = 10.This material was applied as a heterogeneous catalyst in the reaction of ethyl transesterification as raw coconut oil in natura. Coconut oil presented suitable for obtaining biodiesel via ethyl route.The visual aspects and physical-chemical characteristics of the reaction products show that AlSBA-15 catalyst favored the reaction. According to physical-chemical analysis the order of oxidative stability of the product of the transesterification reaction was: catalytic reaction at 1500 ° C> non-catalytic reaction at 100 ° C> 100 ° C catalytic> catalytic reaction at 200 ° C Reaction. The results of oxidative stability and kinematic viscosity shows that the biodiesel produced in the catalytic sandblasting held at 150 ° C which was maintained within the ABNT NBR 7148, ABNT NBR 10441 and EN 14112.

Produção do espaço e reestruturação produtiva do setor de laticínio no Rio Grande do Norte

Since the 1970s, Brazil has gone through several changes in its economic and productive structures, which have symbiotic relationship with the organization and dynamics of the Brazilian territory. This set of economic, social and technical-scientific transformations developed in the amid the productive capital restructuring, a process that occurs on a global scale, but that effective with particularities in different places. Adopting this presuposition the present research had as main objective analyze the productive restructuring of the dairy sector in Rio Grande do Norte, highlighting its relationship with production process / organization of space and its impact on the social relations of production. The adopted methodology to elaborate of this study was based on the achievement a bibliographic review with regard to proceedings of production of space and productive restructuring, document research about the dynamics of the dairy sector in Rio Grande do Norte, as well as on regulatory instructions governing the dairy production in Brazil, we achieve parallel secondary data collection, with official organs such as IBGE, EMATER and SINDLEITE. Another important methodological resource was the realization of the field research, which enabled us to empirically understand the distinct realities lived by agents acting on milk production system in Rio Grande do Norte. The analyzes performed nevertheless evidence that the restructuring process in the dairy sector is fomented, greatly by state,that finance, encourages and normatizes the production of milk in the country. In the specific case of Rio Grande do Norte, this process is boosted by the creation of "Programa do Leite," which by constituting of an institutional market, contributes to the strengthening and expansion of industries, the detriment of the artisanal processing sector. Nevertheless family farmers continue to act in the activity, be only producing and trading fresh milk, supplying milk to processing units, mediating the production of their peers or by the craft benefiting milk in traditional cheese factories presents in the entire state of Rio Grande do Norte. The results reveal that it is a complex web of social relations of production that are established at the heart of laticinista activity in the Rio Grande Norte, these are summarily marked by relations of competition and complementarity between industrial and artisanal processing of milk

Guia do autor da Editora da UFRN

Este guia tem o objetivo de trazer informações acerca da submissão de propostas de publicação pela Editora da UFRN, bem como de esclarecer sobre os processos de produção pelos quais passam o original do autor até o seu lançamento e comercialização.

Apoio governamental à inovação Tecnológica: análise da indústria farmacêutica paraense

The transformations economical, cultural and social that happen in world ambit they are associated to the intense progress and expansion of new technologies, forcing governments, people, companies and nations to the introduction of new patterns of behavior, forcing, in that way, to the continuous renewal of products and technological processes to maintain the competitiveness, so much among nations, as in the managerial world. In that matter, the technological innovation is recognized as basic factor of maintainable economical competitiveness, being the responsible for the breaking and/or improvement of the techniques and production processes, what presupposes the systematization varied institutional arrangements that they involve firms, interaction nets among companies, government agencies, universities, research institutes, laboratories of companies and scientists and engineers activities. Those arrangements, to the if they articulate with the educational system, with the industrial and managerial section and, also, with the financial institutions, they take the form that Freeman (1987) it coined of national system of innovation, promoted through public politics of CT&I, which seek to induce and to support innovative initiatives in the companies, as well as to establish demands and to prioritize vocations and regional potentialities. In that context of government support to the technological innovation interferes this study, that it looked for to know the reasons of the fragility innovative in the pharmaceutical industry of State of Pará in Brazil, pointed for PINTEC (2005), starting from the point of view of the businessmen of that section. For such, the qualitative approach was used - with interviews directing semi and the technique of the content analysis. The results of the research pointed that the fragilities innovative of the section links to the ignorance of the government support to the technological innovation on the part of the businessmen of the pharmaceutical industry of State of Pará in Brazil

Depois das fronteiras: a formação dos espaços de pobreza na periferia norte de Natal-RN

The periphery of the city of Natal was built during the last 20 years, trough informal land developments. This dissertation analyses the urbanization of Natal`s North Zone, the largest residential area in the city where 40% of the population lives. This urban space is characterized as a space of poverty because of its majority of low income dwellers as well as lack of infrastructure. The main objective here is to identify and characterize this space as well as resulting segregation. Variables as income, space morphology, residential typology and the history of real estate development as well as dweller`s history of life are analysed

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Otimização de solução extrativa e desenvolvimento tecnológico de produto seco por aspersão de Psidium guajava L.

The increasing in the consumption of plant medicine by parts of the population generated a bigger need for studies. Drug substitutions, changes and adulterations at the production techniques are common places at plant-originated drugs trade, leading governmental departments of drug control round the world to adopt many analytical practices to medicinal plants. However, agronomic and technological issues cause characteristics and chemical composition variation at the drug, problem to be solved by the subject researchers. The present work aims to obtain a spray dried extract from a extractive solution obtained from Psidium guajava L. leaves based in book references that stress the intermediate dosage forms advantages. It also tries to validate useful methodologies for the quality control for both raw material and its derivates. Using eight sets of the spray dried extract (with Eudragit®, Aerosil ® e Avicel PH101 ® as drying adjuvants), the study proposes analytical methods using techniques commonly performed to plant medicines and its intermediate forms. As results, a viable spray-dried extract was obtained from a standartized extract solution. Among the studied adjuvants, the combination Aerosil ® with Eudragit ® showed the drying outcome, rheology, humidity and tannin content values that best fitted the demands of the Brazilian Pharmacopaea

De socialidades mediadas e do homer a propósito do espectador-reativo em Jesús Martín-Barbero

This study aims to examine the contemporary viewer and also propose a review of the literature surrounding the spanish researcher Jésus Martín-Barbero. The proposed review, based on Martín-Barbero observations and the Latin American Cultural Studies analysis, observes the individual as part of the processes of communication and research on the concept of cultural mediation, the viewer as component/agent/object of the production of meaning. The study will perceive it as an element of inaccuracy/inadequacy and understand it as a subject of these reactive processes that contain complex and involve communication and culture, in contrast the impressions that resulted from a discussion between a television professional and a communication researcher and of these findings on the same viewer. The work also aims to point the viewer as a component of the possible mapping desired by Martín-Barbero to massive contemporary interpretation of the processes and its concept of night map