Concreto celular polimérico: influência na adição de resíduo de poliéster insaturado termofixo

This work addresses the production of lightweight concrete building elements, such as plates, prefabricated slabs for pre-molded and panels of fencing, presenting a singular concrete: the Lightweight Concrete, with special properties such low density and good strength, by means of the joint use of industrial waste of thermosetting unsaturated polyesters and biodegradable foaming agent, named Polymeric Lightweight Concrete. This study covered various features of the materials used in the composition of the Polymeric Lightweight Concrete, using a planning of factorial design 23, aiming at studying of the strength, production, dosage processes, characterization of mechanical properties and microstructural analysis of the transition zone between the light artificial aggregate and the matrix of cement. The results of the mechanical strength tests were analyzed using a computational statistics tool (Statistica software) to understand the behavior and obtain the ideal quantity of each material used in the formula of the Polymeric Lightweight Concrete. The definition of the ideal formula has the purpose of obtaining a material with the lowest possible dry density and resistance to compression in accordance with NBR 12.646/92 (≥ 2.5 MPa after 28 days). In the microstructural characterization by scanning electron microscopy it was observed an influence of the materials in the process of cement hydration, showing good interaction between the wrinkled face of the residue of unsaturated polyesters thermosetting and putty and, consequently, the final strength. The attaining of an ideal formula, given the Brazilian standards, the experimental results obtained in the characterization and comparison of these results with conventional materials, confirmed that the developed Polymeric Lightweight Concrete is suitable for the production of building elements that are advantageous for construction

Aplicação de técnicas eletroquímicas na determinação do potencial de corrosividade de ligas de alumínio em água produzida

The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed

Diversidade de espécies e ecologia da comunidade de lagartos de um fragmento de Mata Atlântica no nordeste do Brasil

Neste estudo foram investigadas a diversidade, a composição, e as diferenças no uso do espaço (hábitat e microhábitat) e do alimento em uma comunidade de lagartos habitantes da serapilheira de um fragmento de Mata Atlântica, do Estado de Alagoas, Brasil. Para a observação e/ou coleta dos espécimes, foram utilizados os métodos de busca ativa e armadilhas de queda (pit-fall traps) sem cerca-guia. Para análises de diversidade e da existência de diferenças de diversidade entre os hábitats e microhábitats, utilizou-se o índice de Shannon. A largura dos nichos espacial (hábitat e microhábitat) e alimentar foi avaliada, utilizando-se o índice de diversidade de Simpson. A similaridade entre as áreas foi averiguada utilizando-se o índice de Jaccard. Para avaliar o grau de sobreposição quanto ao uso do espaço (hábitats e microhábitats) e do alimento pelas espécies, foi utilizada uma versão da equação de MarcArthur & Levis. Foram obtidas vinte e três espécies de lagartos, pertencentes a nove famílias; destas, dezenove foram obtidas no interior da mata e nove na borda. Para o interior da mata as espécies mais abundantes foram Kentropyx calcarata, Dryadosaura nordestina, Enyalius catenatus e Gymnodactylus darwinii. Na borda da mata as espécies mais abundantes foram Tropidurus hispidus, T. semitaeniatus, Ophiodes striatus e Ameiva ameiva. Quanto à utilização dos recursos, os resultados mostraram que espécies filogeneticamente próximas nem sempre utilizam de maneira semelhante os recursos disponíveis. A dieta em geral foi composta por artrópodes. Tropidurus hispidus e T. semitaeniatus se mostraram especialistas no consumo de Himenoptera (Formicidae), que estiverem presentes em 100% dos seus estômagos. Ophiodes striatus teve como principal alimento caramujos (Gastropoda) e aranhas com 60% cada; sendo Gastropoda mais abundante para esta espécie

Avaliação da eficiência de lagoas de estabilização no tratamento de resíduos esgotados de fossas sépticas

Because of disability in public policy development in mind to attend issues of sanitation in the municipalities, companies known as "clean-blue" appeared proposing to solve a simple collection and management of wastewater produced in single or multifamily residences, commercial, hospitals, etc. In the case of an activity in which there are no worries about the fate of sewage, emerged some doubts about the degree of health and environmental safety in these companies. Traditionally, most of them makes the provision of waste depleted soil or wetland, open, usually located on the outskirts of cities (MENESES, 2001). In turn, the sludge from septic tanks exhausted, provided no technical criteria - in the soil, rivers and as an agricultural fertilizer put in risk the health of the population and environmental quality. This work was entered in the search network 5 of the Notice of the Research Program in Sanitation - PROSAB-5, aimed to study the theme 'Characterization and study of alternative ways of treating sludge from septic tanks in the city of Natal, RN', proposing to evaluate the performance of the use of stabilization ponds as a system to handle waste from septic tanks exhausted. A series of lakes studied belong to one of the largest clean-pit of Natal, consisting of two anaerobic ponds, one facultative and maturation, and a tank disinfection, the wastewater being released in the Potengi River. Samples were collected between the months of October 2007 to October 2008, at six points previously defined and judged as more appropriate to what is proposed study. The analysis results in field and laboratory showed the most significant removal of COD (88.93%), total suspended solids (94.87%), organic nitrogen (66.87%) and thermotolerant coliforms (99.88%). Some results have not reached the expected because the system under study had operating problems that have undermined the efficiency of the reactors

Caracterização genética de vacas leiteiras por meio de marcadores moleculares e suas implicações na composição e qualidade do leite

The objective of this study was to identify DNA polymorphisms at the genes leptin, β-lactoglobulin and pituitary-specific transcription factor in three genetic groups of Holstein x Guzerat dairy cows and investigate the relationship between their genotypes and the composition and quality of milk of dairy cows. Samples were collected in August 2009, being 113 blood samples from lactating crossbred cows and 58 milk samples. For analysis of DNA polymorphisms blood samples were collected, analyzed later in the Genetic Laboratory affiliated to the Zootechny Institute of São Paulo and individual milk samples were collected according to standards established by the laboratory of Management Program of Northeast Dairy Herds (PROGEN), at Federal Rural University of Pernambuco (UFRPE) for analysis of milk composition and quality. The characterization of genotypes was performed by PCR-RFLP, for which were designed specific primers for each studied gene and restriction enzymes Kpn2I, HaeIII and HinfI that cut the DNA of the following genes: leptin, β-lactoglobulin and a PIT, respectively. The leptin estimate genotypic frequence were CC 0.112, TT 0.225 and CT 0.661, for β-lactoglobulin were AA 0.136, AB 0.323 and BB 0.539, and for PIT were ++ 0.655, -- 0.311 and +- 0.032. The results show that the population is in Hardy-Weinberg disequilibrium for leptin, β-lactoglobulin and a PIT due to excess of heterozygotes in the population, however, as these genes are associated with the milk production it is considered that the animals have genetic potential for milk production in the Brazilian semi-arid conditions. Through the characterization of the studied herd there were not found implications of the polymorphism of leptin, β-lactoglobulin and PIT in the composition and quality of milk from cows in the different genetic groups 1/2, 3/4 and 7/8 Holstein x Guzerat. Key words: β-lactoglobulin, crossbred cows, leptin, PCR-RFLP, PIT1, semi-arid.

Influência do pré-aquecimento na adaptação marginal de dois materiais seladores de fóssulas e fissuras, analisada através de tomografia de coerência ótica

Among the non-invasive techniques employed in the prevention of caries highlights the sealing pits and fissures which is a conservative maneuver, in order to obliterate them to protect them from attack acid bacteria. Influenced by the studies of pre-heating composite resin, which has experienced great improvement in some of their physical properties, this study aimed to evaluate in vitro the superficial and internal marginal adaptation of different materials and sealants in pre-heating or not. A total of 40 extracted human third molars (n=10) that had their occlusal surfaces prepared to receive sealant. We tested two types of sealing materials: resin sealant (Fluoroshield) and low-viscosity resin (Permaflo), where 50% of previously received heated material and the other half received sealant material at room temperature. All samples were subjected to thermal cycling and pH, simulating a cariogenic oral environment, and later were analyzed appliance OCT (optical coherence tomography). The images obtained alterations were recorded and analyzed statistically. Change was considered as the emergence of bubbles, gaps and cracks in the sealant. Comparisons of the same material, assessing the fact that it is not sealed or preheated material, as well as comparisons between different materials subjected to the same temperature were carried out. The nonparametric Tukey test was used (p < 0,05). The results showed that there was statistically significant difference between both the materials analyzed, as between the situations in which the sealant material was submitted (preheated or not). On the issue of marginal adaptation and internal surface, seen through Optical coherence tomography, may suggest that there is a difference between the use of one type or another of the sealing material analyzed, with superiority attributed to resin Permaflo compared to sealant Fluroshield, telling is the same for the different techniques used