Análise do desempenho térmico de um sistema de aquecimento solar utilizando coletor com superfície absorvedora em chapas de PVC

It s presented a solar collector to be used in a system for heating bath water, whose main characteristic is its low cost. The collector consists of five plates of PVC with 10 mm thick, 200 mm in width and 1400mm in length, with an area equal to 1.4 square meters. The plates were connected in parallel to the ends of PVC tubes of  40 mm and 32 mm. The plates were coated on one side with aluminum sheets of soft drinks and beers cans open. The system worked on a thermosiphon and was tested in two configurations: the plates uncoated and coated with aluminum material, to determine the influence of material on the efficiency of the collector. For both configurations was used EPS plates below the surface to minimize heat losses from the botton. The thermal reservoir of the heating system is, also, alternative and low cost, since it was constructed from a polyethylene tank for storing water, with volume of 150 end 200 liters. It will be presented the thermal efficiency, heat loss, water temperature of the thermal reservoir at the end of the process and simulation of baths for a house with four residents. The will be demonstrated thermal, economic and material viability of the proposed collector, whose main innovation is the use of recyclables materials, cans of beer and soft drinks, to increase the temperature of the absorber plate.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Modificação do eletrodo AWS E7018 com adição de filmes finos externos de PVC e Al, para soldagem de aço C-Mn

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Análise da eficiência de contratos de serviços de elevada especificidade terceirizados pela petrobras

The definition of the boundaries of the firms is subject that has occupied the organizational theorists long ago, being the seminal work of Coase (1937) indicated as the trigger for one theoretical evolution, with emphasis on governance structures, which led to a modern theory of incomplete contracts. The Transaction Cost Economics (TCE) and Agency Theory arise within this evolution, being widely used in studies related to the theme. Empirically, data envelopment analysis (DEA) has established itself as a suitable tool for analysis of efficiency. Although TCE argues that specific assets must be internalized, recent studies outside the mainstream of theory show that, often, firms may decide, for various reasons, hire them on the market. Researches on transaction costs face with the unavailability of information and methodological difficulties in measuring their critical variables. There`s still the need for further methodological deepening. The theoretical framework includes classic works of TCE and Agency Theory, but also more recent works, outside the mainstream of TCE, which warn about the existence of strategies in use of specific assets that aren`t necessarily aligned with the classical ideas of TCE. The Brazilian oil industry is the focus of this thesis, that aimed to evaluate the efficiency of contracts involving high specificity service outsourced by Petrobras. In order to this, we made the categorization of outsourced services in terms of specificity, as well the description of services with higher specificity. Then, we verified the existence of relationship between the specificity of services and a number of variables, being found divergent results than those that are preached by the mainstream of TCE. Then, we designed a DEA model to analyze the efficiency in the use of onshore drilling rigs, identified among the services of highest specificity. The next step was the application of the model to evaluate the performance of drilling rigs contracts. Finally, we verified the existence of relationship between the efficiency of contracts and a number of variables, being found, again, results not consistent with the theory mainstream. Regarding to analyze of efficiency of drilling rigs contracts, the model developed is compatible with what is found in academic productions in efficiency of drilling rigs. The results on efficiency show a wide range of scores, with efficiencies ranging from 31.79% to 100%, being low the sample efficiency average. There is consonance between the model results and the practices adopted by Petrobras. The results strengthen the DEA as an important tool in studies of efficiency with possibility to use for analysis other types of contracts. In terms of theoretical findings, the results reinforce the arguments that there are situations in which the strategies of the organizations, in terms of use of assets and services of high specificity, do not necessarily follow what is recommended by the mainstream of TCE

Inserção de fornecedores locais como fonte de desempenhos em custos de transação e legitimidade: estudo de caso na cadeia produtiva do petróleo e gás do Rio Grande do Norte

The inclusion of local suppliers in production chains has considerable impact on its performance, but most notably in its main actors. The results of this process may be of different kinds and can be analyzed from economic or institutional approaches. This study aimed to verify the existence of different performances of Petrobras due to the inclusion of local suppliers in the oil and gas production chain in the state of Rio Grande do Norte, from the viewpoints of transaction costs and the Institutional Theory. In order to this, were made the characterization of the PROMINP, the description of its actions and results, the mapping of its institutional context of reference, and identification of results obtained by Petrobras in terms of transaction costs and legitimacy. The theoretical framework is based on authors dealing with industrial concentration, as like Marshall, Krugman, Porter and Schmitz, from the sociological perspective of neoinstitucional theory, as like DiMaggio and Powell and Scott and Meyer, and transaction costs, as like Williamson. This is a qualitative research, with data collection done by consulting secondary fonts and semi-structured interviews with nineteen actors of three groups, namely: actors involved in actions of the program, representatives of enterprises and representative of Petrobras. To analyze the content was used the Suchman s model (1995) for categories associated with strategies of legitimation and fourteen variables associated with the three variables assets specificity, bounded rationality and opportunism (Williamson, 1995, 1989) in the case of transaction costs. The results indicate that PROMINP has achieved its objectives by encouraging the increased participation of local companies in the oil and gas production chain, reflecting in the economic development of the state. The Redepetro/RN, fostered and built upon the interaction of the participants, is presented as a solution of continuity to the participation of enterprises in the chain, after the closure of the actions of the program. PROMINP demands responses to coercive, legislative and regulatory pressures of the organizational field, whose institutional context of reference is wide. From the point of view of legitimacy, through strategies to gain cognitive legitimacy and maintaining pragmatic legitimacy, Petrobras can manipulate the environment, ensuring the compliance of the constituents to their technical and institutional demands. Enterprises, in turn, respond to the demands through compliance with technical demands, mainly through the certification of processes, and cultural changes. There aren t clear gains related to the transaction costs, however, gains in legitimacy can be seen as a cumulative capital that can serve as a competitive differential that generates economic gains. In terms of theoretical findings, it was found that, due to its explanatory power for actions that are difficult to explain only in economic terms, Institutional Theory may be used as theoretical support concurrent with other theories. TCE model has limitations in explaining the program actions. In the case, it s emphasized that Petrobras doesn t seek only economic efficiency, but has in its mission the commitment to social development.

Influência da profundidade e dos parâmetros ambientais sobre o desenvolvimento de Gracilaria birdiae (Rhodophyta, Gracilariales) em viveiro de camarão

This study evaluates the influence of depth and environmental parameters on the development of Gracilaria birdiae Plastino & Oliveira (Gracilariaceae Rhodophyta) in an organic shrimp pound (Litopenaeus vannamei) under euthrophical conditions. PVC structures (module) witch four ropes laden with 150 g of macroalgae each, were kept during 35 days at three different depths (surface, 10 and 20 cm depth). Wet biomass weighing and environmental parameters (temperature, salinity, turbidity, pH, transparence, precipitation, evaporation, insolation, accumulated solar radiation, nitrite, nitrate, ammonium and orthophosphate) were measured weekly. At all three proposed depths, the macroalgae displayed a higher biomass at the end of experiment than at the initial inoculations. The module kept at a 10 cm depth presented the greatest average biomass (186,3), followed by that kept at 20 cm (180,4 g) and the surface module (169,9 g). Biomass variations showed algae to suffer the direct effects of depths. Biomass loss was associated with the factors that influence light penetration, such as sediment deposits above the thallus, rate of evaporation and precipitation. The smallest loses occurred in the algae kept on surface (0,16%), followed by the algae kept at 20 cm (0,20%) and 10 cm (0,22%). The specific growth rate (SGR) of G. birdiae showed no significant difference between the three depths nor the sample periods. Nevertheless, the modules kept at 10 and 20 cm depths presented similar growth evolution, both growing 0,38%·per day-1, while the module kept on surface had an average SGR of 0,36%·day-1. The models related to growth rate demonstrated temperature, salinity, pH, orthophosphate, ammonium, precipitation and turbidity as the principal environmental parameters influencing the development of G. birdiae

Efeito dos nutrientes (nitrogênio e fósforo) sobre o desenvolvimento da Gracilaria birdiae: crescimento e possível uso como biofiltro

Marine shrimp farming has grown exponentially during the last years in Brazil. In spite of the promising economical situation, this activity is facing an increasing criticism due to its environmental impact. Thus, the necessity of alternatives to mitigate environmental degradation caused by this activity. An alternative that is being studied is the policulture that is the integrated culture of two or more organisms, normally one of them a filtering organism. Among filtering organisms, macroalgae are very practicable because they are efficient in the removal of the exceeding nutrients of the water and do not leave residues in the water. Besides, the integrated culture with macroalgae allows the economical exploration of the seaweed (for the manufacture of jelly and jam, for the dairy industry, pharmaceuticals, etc.) along with possibility of a sustainable aquaculture. In the present experiment, the development of the seaweed Gracilaria birdiae, the influence and tolerance of this species to the environmental parameters, and its absorption efficiency in relation with the three kinds of macronutrients (NH4+, NO3- and PO4-3) found in the effluents of marine shrimp farming was studied. The experiment was divided in two parts: a laboratorial part and one part carried under natural conditions. The water used in the laboratory trial was collected in the shrimp ponds of Tecnarão farm and distributed in aquaria containing 20 g of G. birdiae. In the field trial, 0.5 kg of G. birdiae was inserted in PVC cages cultivated in the farm. The results of the study showed a modest growth of G. birdiae, probably due to its low tolerance to highly eutrophicated environments. However, the removal of nutrients was very expressive. Ammonia was reduced in approximately 34 %. Ortho-phosphate showed a reduction of 93.5 %. The capacity of biofiltration of the NO3- by the macro algae was of 100 %, showing that G. birdiae is a seaweed-filtered with a high level of removal for this nutrient under laboratorial conditions. In spite of the low growth of the macro algae in the experiment, the results in relation to the removal of nutrients of the water was encouraging, suggesting that this species can be an efficient biofilter and thus, a strong candidate to be used in a sustainable aquaculture

Utilização da macroalga Ulva lactuca linnaeus na redução de nutrientes (NH4+,NO3- e PO4-2) provenientes da carcinicultura

Dentre as macroalgas capazes de absorver altas concentrações de N e P dissolvidos na água, destaca-se a Chlorophyta Ulva lactuca, bastante adaptável e resistente às adversidades ambientais, como grandes variações de temperatura, salinidade, matéria orgânica e metais pesados. Trata-se também de uma espécie bastante comum nas áreas intertidais do litoral norte-riograndense. Devido a suas características ecológicas, fisiológicas e nutricionais, foi avaliado nesse estudo, o seu potencial como biofiltro na redução de NH4+, NO3- e PO4-2, tanto em condições controladas como também em um viveiro de camarão. No experimento laboratorial, foram utilizados quatro aquários de vidro de 30 x 20 x 20cm com 10L de água, sendo três aquários experimentais contendo 20g de U. lactuca e um controle. O acréscimo de biomassa foi de 2,92g (22,92 ± 6,29g; p < 0,05) em relação ao inóculo inicial de 20g, sob temperatura (28,50 ± 0,58ºC), salinidade (35,00 ± 0,00 ), pH (8,26 ± 0,02) e luz constante (250 μmol.m2s-1). O crescimento positivo (1,78 ± 4,38%dia-1; p < 0,05), juntamente com a alta eficiência de absorção de amônio (83%; p < 0,001), nitrato (83%; p < 0,001) e ortofosfato (53%; p < 0,001), demonstrou que, nessas condições, a Ulva lactuca absorveu os nutrientes e aumentou sua biomassa. Já no experimento de campo, realizado na fazenda TECNARÃO, situada no município de Arez/RN (06° 11 40 Latitude Sul, e 35º 09 37 Longitude Oeste), foram utilizadas três gaiolas de PVC, posicionadas a 12cm da superfície da água, cada uma com dimensões de aproximadamente 59 x 59 x 15cm, onde foram colocadas 200g de U. lactuca. O ganho de biomassa de 3g (203,00 ± 41,02g; p < 0,001) foi muito semelhante às condições controladas, demonstrando a adaptabilidade da espécie em condições ambientais variáveis, onde, apesar da temperatura pouco variável (27,45 ± 0,64ºC), houve progressiva diminuição de salinidade (25 - 15 ), devido ao período de fortes chuvas (34,70 ± 23,78mm). Somado a isso, foram observados vários fatores biológicos interferindo no viveiro, como a presença de epífitas, organismos endofíticos, fouling e a herbivoria por parte dos próprios camarões. Houve aumento nas concentrações de NH4+ (4,36 ± 1,69 μmol.L-1), NO3- (0,17 ± 0,25μmol.L-1) e PO4-2 (0,41 ± 0,13μmol.L-1), coincidindo com o crescimento da espécie até a terceira semana. Todos os parâmetros ambientais analisados, assim como a biomassa e a Taxa de Crescimento Relativo (TCR), obtidos no campo, apresentaram variações altamente significativas (p < 0,001). As correlações observadas entre biomasa e NH4+ (r = 0,82; p < 0,001) e entre biomassa e PO4-2 (r = 0,87; p < 0,001), indicam que esta espécie é capaz de ter um crescimento satisfatório nas condições eutróficas de um viveiro de camarão, sendo possível seu uso como biofiltro.

Viabilidades térmica, econômica e de materiais de um sistema solar de aquecimento de água a baixo custo para fins residenciais

An solar alternative system for water heating is presented. Is composed for one low cost alternative collector and alternative thermal reservoir for hot water storing. The collector of the system has box confectioned in composite material and use absorption coils formed for PVC tubes. The box of hot water storage was confectioned from a plastic polyethylene drum used for storage of water and garbage, coated for a cylinder confectioned in fiber glass. The principle of functioning of the system is the same of the conventionally. Its regimen of work is the thermosiphon for a volume of 250 liters water. The main characteristic of the system in considered study is its low cost, allowing a bigger socialization of the use of solar energy. It will be demonstrated the viabilities thermal, economic and of materials of the system of considered heating, and its competitiveness in relation to the available collectors commercially. Relative aspects will be boarded also the susceptibility the thermal degradation and for UV for the PVC tubes. It will be shown that such system of alternative heating, that has as main characteristic its low cost, presents viabilities thermal, economic and of materials

Projeto, construção e análise de desempenho de coletores solares alternativos utilizando garrafas pet

A solar alternative system for water heating is presented. It work on a thermosiphon, consisting of one or two alternative collectors and a water storage tank also alternative, whose main purpose is to socialize the use of energy mainly to be used by people of low income. The collectors were built from the use of pets bottles, cans of beer and soft drinks and tubes of PVC, ½ " and the thermal reservoirs from a drum of polyethylene used for storage of water and garbage placed inside cylinder of fiber glass and EPS ground between the two surfaces. Such collectors are formed by three elements: pet bottles, cans and tubes absorbers. The heating units, which form the collector contains inside the cans that can be closed, in original form or in the form of plate. The collectors have an absorber grid formed by eight absorbers PVC tube, connected through connections at T of the same material and diameter. It will be presented data of the thermal parameters which demonstrate the efficiency of the heating system proposed. Relative aspects will be boarded also the susceptibility the thermal degradation and for UV for the PVC tubes. It will be demonstrated that this alternative heating system, which has as its main feature low cost, presents thermal, economic and materials viabilities

Estudo térmico de um sistema solar de aquecimento de água residencial para duas configurações de superfície absorvedora

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are its low cost and easy manufacturing and assembly. The absorbing surface of the collector is formed by an aluminum plate with eight flaps where they lodge PVC pipes. The catchment area of solar radiation corresponds to 1.3 meters. The collector box was made of wood, is covered by transparent glass and thermal insulation of tire chips and expanded polystyrene (EPS). Absorber tubes were connected in parallel through the use of PVC fittings and fixed to the plate by the use of metal poles and rivets. The entire absorber received paint flat black for better absorption of sunlight. The system worked on a thermosiphon assembly and absorber of the collector has been tested in two configurations: with the tubes facing up, directly exposed to the impact of sunlight and facing down, exchanging heat with the plate by conduction. It was determined the most efficient configuration for the correct purpose. The solar collector was connected to a thermal reservoir, also alternative, low-cost forming the system of solar water heating. We evaluated thermal parameters that proved the viability of the heating system studied

Análise do desempenho térmico de um sistema de aquecimento solar de baixo custo

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are low cost and easy manufacturing and assembly. The system operates under natural convection or thermosiphon. The absorbing surface of the collector is formed by twelve PVC pipes of 25 mm outside diameter connected in parallel via connections in T of the same material. The tubes were covered with absorbing fins made with recycled aluminum cans. We studied eight settings between absorber plate, thermal insulating EPS boards and thermal reservoirs 150 and 200 liters. It was determined the most efficient configuration for the correct purpose. We evaluated thermal parameters that proved the viability of the heating system studied

Projeto, construção e análise de eficiência térmica de um sistema de aquecimento solar de água de baixo custo

We studied the feasibility of using a system of Solar Water Heating (SAS) with low cost, for three configurations. In configurations I and II have the collector grid absorber composed of six PVC tubes placed in parallel on the tile cement. In configuration II, the PVC tubes were transparent cover made of plastic bottles. Configuration III uses a collector composed of 12 black HDPE pipes, supported on four cement tiles 2.44 m x 0.50 m, two by two overlapping and interspersed with a filling of glass wool, comprising an area exposed to the global radiation incident of 2.44 m2, with the top two tiles painted matte black. In this configuration, the HDPE pipes replace conventional PVC pipes painted black. The total cost of SAS for configuration III, the most economical, was around $ 150.00. For the configurations tested the system of operation was thermosyphon collector. The study showed that the proposed systems have good thermal efficiency, are easy to install and handle and have low cost compared to conventional.

Construção e analise de desempenho de um sistema de aquecimento solar de água utilizando placa de policarbonato como superfície absorvedora

It was studied a system for heating water to be used to obtain water for bathing at home, the absorbing surface of the collector is formed by one plate of polycarbonate. The polycarbonate plate has 6 mm thick, 1.050 mm wide and 1.500 mm long with an area equal to 1,575 m². The plate was attached by its edges parallel to PVC tubes of 32 mm. The system worked under the thermo-siphon and was tested for two configurations: plate absorber with and without isolation of EPS of 30 mm thick on the bottom surface in order to minimize heat losses from the bottom. The tank's thermal heating system is alternative and low cost, since it was constructed from a polyethylene reservoir for water storage, with a volume of 200 liters. Will present data on the thermal efficiency, heat loss, water temperature of thermal reservoir at the end of the process simulation and baths. Will be demonstrated the feasibility of thermal, economic and material pickup proposed for the intended purpose.

Análise tribológica de um sistema de acionamento alternativo de pigs para a indústria do petróleo

It is analyzed through the concepts of tribology and mechanical contact and damage the suggestion of implementing a backup system for traction and passage of Pipeline Inspection Gauge (Pig) from the inside of pipelines. In order to verify the integrity of the pipelines, it is suggested the possibility of displacement of such equipment by pulling wires with steel wires. The physical and mechanical characteristics of this method were verified by accelerated tests in the laboratory in a tribological pair, wire versus a curve 90. It also considered the main mechanisms of wear of a sliding system with and without lubricant, in the absence and presence of contaminants. To try this, It was constructed a test bench able to reproduce a slip system, work on mode back-and-forth ("reciprocation"). It was used two kinds of wires, a galvanized steel and other stainless steel and the results achieved using the two kinds of steel cables were compared. For result comparative means, it was used steel cables with and without coating of Poly Vinyl Chloride (PVC). The wires and the curves of the products were characterized using metallographic analysis, microhardness Vickers tests, X-ray diffraction (XRD), X-Ray Refraction (XRF) and tensile tests. After the experiments were analyzed some parameters that have been measurable, it demonstrates to the impracticality of this proposed method, since the friction force and the concept of alternating request at the contact between the strands of wire and the inner curves that are part ducts caused severe wear. These types of wear are likely to cause possible failures in future products and cause fluid leaks