Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Metalização mecânica de ZrO2 com Ti para brasagem ZrO2/Aço com ligas de adição sem metal ativo

Metal/ceramic interfaces using zirconia have dominated the industrial applications in the last decade, due to the high mechanical strength and fracture toughness of zirconia, especially at temperatures below 300 ºC. Also noteworthy is the good ionic conductivity in high temperatures of this component. In this work joining between ZrO2 Y-TZP and ZrO2 Mg-PSZ with austenitic stainless steel was studied. These joints were brazed at high-vacuum after mechanical metallization with Ti using filler alloys composed by Ag-Cu and Ag-Cu-Ni. The influence of the metallization, and the affinity between the different groups (ceramic / filler alloys) was evaluated, in order to achieve strong metal/ceramic joints. Evaluation of joints and interfaces, also the characterization of base materials was implemented using various techniques, such as: x-ray diffraction, leak test, three-point flexural test and scanning electron microscopy with chemical analysis. The microstructural analysis revealed physical and chemical bonds in the metal/ceramic interfaces, providing superior leak proof joints and stress cracking, in order to a good joint in all brazed samples. Precipitation zones and reaction layers with eutetic characteristics were observed between the steel and the filler metal

Análise topológica experimental por perfilometria cíclica indutiva de superficies de paredes estruturais

To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies

Dinâmica de Sedimentação de Lodo em Lagoas de Estabilização

Stabilization ponds are an effective sewage treatment alternative for the climatic conditions prevailing in Brazil. In the present work, a primary facultative pond was studied, in the city of Natal, Rio Grande do Norte, Northeast Brazil. The aim of this study was to evaluate the sedimentation dynamics in the facultative pond. The pond was divided in three section or zones along its length starting from the inlet end namely A1, A2 and A3. The research was accomplished in three phases. In the first the mapping of the sludge layer was done, sludge core samples were also collected for analysis for total, fixed and volatile solids and the depth of the sludge layer was determined using a portable echo sounder. In the second solids sedimentation rates were measured using traps placed in the inlet and outlet zones and in the third phase resuspension sludge was evaluate using a tracer. The amount accumulated sludge since the start operation was 13.583 m3. The sedimentation constant averages changed between 0.93 to 2.94 and 3.90 to 5.80 for the depths of 0.5 and 1.0 m respectively. The relationship between volatile and fixed solids (SV/SF) increased along the pond. The removal efficiencies were 52.12%, 36.09%, and 37.50% for BOD, COD and SS, respectively. The sludge accumulation model proposed had a good adjustment with 0.17 m3/hab.year rate. The results presented here demonstrated that the wind had a direct influence on the sedimentation of solids in this pond affecting the efficiency and sludge accumulation

A ocupação urbana do entorno de zonasde proteção ambiental de natal, suas condições de sustentabilidade e a relação com a ocorrência de insetos vetores

This study started from the hypothesis of the existence of a relation between the type of the urban occupation concerning to the sustainability conditions at the proximity of Environment Protected Zones and the occurrence of vectors insects in Natal, Rio Grande do Norte, Brazil. This research, which used data available by the City Administration Health and Urbanization Secretaries (respectively SMS and SEMURB), in the time period of 2006 to 2008, aimed to characterize the study site in terms of urban occupation, relating it to social environmental aspects of land occupation and the occurrence of vectors insects. This study is presented in two papers, the first one linking the occurrence of vectors insects and sustainable development indicators and the second relating the incidence of reported cases of Dengue and Dengue Hemorrhagic Fever (DHF) and the occurrence of larvae infection indexes of Aedes aegypti, in Natal, Rio Grande do Norte State. In the first paper, was made a correlation between Dengue Fever vectors and Visceral and Tegumentar Leishmaniasis vectors and sustainable development indicators, selected from IDS Brasil- 2008. Through factorial analysis a Sustainability Index (SI) was acquired for each region, the northern region of the municipality obtained lower numbers than southern region, which, in its turn, presented better sustainability conditions. Linking this index to vector infestation parameters shows a high significant correlation between the SI and the Breteau Index of Aedes aegypti (p=0,028) as well as with SI and sand flies infestation index (p=0,01). Higher rates in vectors infestation in regions with a lower Sustainable Development Index demonstrates that this index can be used to determine the increasing of probability of Aedes and sand flies occurrence in urban environment. The second paper analyzed the occurrence of the main vector of Dengue and DHF, the Aedes aegypti mosquito, and the relation between larvae infection indexes of this insect and reported cases of the diseases. This study revealed unexpected relation where areas with higher Breteau s Indexes showed lower infection rates of Dengue Fever, although showing high incidence of DHF

Evolução geodinâmica e condicionamento estrutural dos terrenos Piancó-Alto Brígida e Alto Pajeú, domínio da zona transversal, NE do Brasil

This thesis aims to advance in the geological knowledge of the region comprising the Piancó-Alto Brígida (TPAB) and Alto pajeú (TAP) terranes, in the Transversal Zone Domain (Borborema Province, NE Brazil), with the main objective of understanding the geodynamic evolution and the structural framework of these units. To reach this objective, and besides field work and interpretation of traditional aerial photographs, other tools were employed like of remote sensing products (Landsat 7 ETM+, aeroradiometrics, aeromagnetics and topographical images), lithogeochemical (whole rock) analyses and geochronological dating (U-Pb in zircon), besides integration with literature data. In the area, several precambrian geological units outcrop, represented in the TAP by the paleoproterozoic Serra Talhada and Afogados da Ingazeira complexes, Riacho Gravatá Complex (metavolcano-sedimentary sequence of Stenian-Tonian age) and Cariris Velhos orthogneisses (of Tonian age). The TPAB comprises the Santana do Garrote (lower unit) and Serra do Olho d'Água (upper unit) formations of the Cachoeirinha Group (Neoproterozoic III), besides the Piancó orthogneisses and Bom Jesus paragneisses; the latter correspond to an older (basement ?) block and a possible high grade equivalent of the Cachoeirinha Group (or Seridó Group ?), respectively. Several Brasiliano-age plutons occur in both terranes.The aeromagnetic data show the continuity, at depth, of the main shear zones mapped in the region. The Patos, Pernambuco, Boqueirão dos Cochos, Serra do Caboclo, Afogados da Ingazeira/Jabitacá and Congo-Cruzeiro do Nordeste shear zones reach depths greater than to 6-16 km. The aeromagnetic signature of other shear zones, like the Juru one, suggests that these structures correspond to shallower crustal features. The satellite images (Landsat 7 ETM+) and aerogamaspectrometric images discriminate different geological units, contributing to the mapping of the structural framework of the region. The Serra do Caboclo Shear Zone was characterized as the boundary/suture between the TPAB and TAP. This structure is an outstanding, pervasive feature that separates contrasting geological units, such as the Neoproterozoic III Cachoeirinha Group in the TPAB and the Riacho Gravatá Complex and the Cariris Velhos metaplutonics, of Stenian-Tonian age, in the TAP. Occupying different blocks, these units are not found in authoctonous relations, like unconformities and intrusive contacts. Concerning the Cariris Velhos (ca. 1,0 Ga old) event is recorded by radiometric ages of the Riacho Gravatá Complex metavolcanics and intrusive augen and orthogneisses, all of them displaying geochemical affinities of arc or collisional settings. A structural signature of this event was not recorded in the region, possibly due to its low grade/low strain style, obliterated by the overprinting of younger, higher grade/high strain Brasiliano-age fabrics.The first tectonic event (D1) observed in the Cariris Velhos lithotypes presents contractional kinematics with transport to the NW. Neoproterozoic III geochronologic dates, obtained in late-D1 granitoids, imply a Brasiliano age (ca. 610-600 Ma) for this deformation event. The second tectonic event (D2) characterized in the region corresponds to the Brasiliano transcurrent kinematics of the outstanding shear zones and associated granitoid plutons. The geochronological (U-Pb in zircon) data obtained during this thesis also confirms the occurrence of the Cariris Velhos magmatic suite in the TAP, as well as the Neoproterozoic III age to the Cachoeirinha Group in the TPAB. The TAP (Riacho Gravatá Complex, augen and orthogneisses) is interpreted as a continental arc possibly accreted to a microcontinent during the Cariris Velhos (Stenian-Tonian) event. Later on, this terrane collided with the TPAB at the beginning of the Brasiliano orogeny (D1 contractional deformation), and both domins were reworked by the transcurrent shear deformation of the D2 event

Litoestratigrafia e deformação cenzóica na região de Icapuí, Ceará, e implicações para a estruturação de campos de petróleo na borda ocidental da bacia Potiguar(NE do Brasil)

This thesis deals with the sedimentological/stratigraphic and structural evolution of the sedimentary rocks that occur in the NW continental border of the Potiguar Basin. These rocks are well exposed along coastal cliffs between the localities of Lagoa do Mato and Icapuí, Ceará State (NE Brazil). The sedimentological/stratigraphic study involved, at the outcrop scale, detailed facies descriptions, profile mapping of the vertical succession of different beds, and columnar sections displaying inferred lateral relationships. The approach was complemented by granulometric and petrographic analyses, including the characterization of heavy mineral assemblages. The data set allowed to recognize two kinds of lithological units, a carbonate one of very restricted occurrence at the base of the cliffs, and three younger, distinct siliciclastic units, that predominate along the cliffs, in vertical and lateral extent. The carbonate rocks were correlated to the late Cretaceous Jandaíra Formation, which is covered by the siliciclastic Barreiras Formation. The Barreiras Formation occurs in two distinct structural settings, the usual one with nondeformed, subhorizontal strata, or as tilted beds, affected by strong deformation. Two lithofacies were recognized, vertically arranged or in fault contacts. The lower facies is characterized by silty-argillaceous sandstones with low-angle cross bedding; the upper facies comprises medium to coarse grained sandstones, with conglomeratic layers. The Tibau Formation (medium to coarse-grained sandstones with argillite intercalations) occurs at the NW side of the studied area, laterally interlayered with the Barreiras Formation. Eolic sediments correlated to the Potengi Formation overly the former units, either displaying an angular unconformity, or simply an erosional contact (stratigraphic unconformity). Outstanding structural features, identified in the Barreiras Formation, led to characterize a neocenozoic stress field, which generated faults and folds and/or reactivated older structures in the subjacent late cretaceous (to paleogene, in the offshore basin) section. The structures recognized in the Barreiras Formation comprise two distinct assemblages, namely a main extensional deformation between the localities of Ponta Grossa and Redonda, and a contractional style (succeeded by oblique extensional structures) at Vila Nova. In the first case, the structural assemblage is dominated by N-S (N±20°Az) steep to gently-dipping extensional faults, displaying a domino-style or listric geometry with associated roll-over structures. This deformation pattern is explained by an E-W/WNW extension, contemporaneous with deposition of the upper facies of the Barreiras Formation, during the time interval Miocene to Pleistocene. Strong rotation of blocks and faults generated low-angle distensional faults and, locally, subvertical bedding, allowing to estimate very high strain states, with extension estimates varying between 40% up to 200%. Numerous detachment zones, parallel to bedding, help to acommodate this intense deformation. The detachment surfaces and a large number of faults display mesoscopic features analoguous to the ones of ductile shear zones, with development of S-C fabrics, shear bands, sigmoidal clasts and others, pointing to a hydroplastic deformation regime in these cases. Local occurrences of the Jandaíra limestone are controled by extensional faults that exhume the pre-Barreiras section, including an earlier event with N-S extension. Finally, WNWtrending extensional shear zones and faults are compatible with the Holocene stress field along the present continental margin. In the Vila Nova region, close to Icapuí, gentle normal folds with fold hinges shallowly pluging to SSW affect the lower facies of the Barreiras Formation, displaying an incipient dissolution cleavage associated with an extension lineation at high rake (a S>L fabric). Deposition of the upper facies siliciclastics is controlled by pull-apart graben structures, bordered by N-NE-trending sinistral-normal shear zones and faults, characterizing an structural inversion. Microstructures are compatible with tectonic deformation of the sedimentary pile, burried at shallow depths. The observed features point to high pore fluid pressures during deformation of the sediments, producing hydroplastic structures through mechanisms of granular flow. Such structures are overprinted by microfractures and microfaults (an essentially brittle regime), tracking the change to microfracturing and frictional shear mechanisms accompanying progressive dewatering and sediment lithification. Correlation of the structures observed at the surface with those present at depth was tested through geophysical data (Ground Penetrating Radar, seismics and a magnetic map). EW and NE-trending lineaments are observed in the magnetic map. The seismic sections display several examples of positive flower structures which affect the base of the cretaceous sediments; at higher stratigraphic levels, normal components/slips are compatible with the negative structural inversion characterized at the surface. Such correlations assisted in proposing a structural model compatible with the regional tectonic framework. The strong neogenepleistocene deformation is necessarily propagated in the subsurface, affecting the late cretaceous section (Açu and Jandaíra formations), wich host the hydrocarbon reservoirs in this portion of the Potiguar Basin. The proposed structural model is related to the dextral transcurrent/transform deformation along the Equatorial Margin, associated with transpressive terminations of E-W fault zones, or at their intersections with NE-trending lineaments, such as the Ponta Grossa-Fazenda Belém one (the LPGFB, itself controlled by a Brasiliano-age strike-slip shear zone). In a first step (and possibly during the late Cretaceous to Paleogene), this lineament was activated under a sinistral transpressional regime (antithetic to the main dextral deformation in the E-W zones), giving way to the folds in the lower facies of the Barreiras Formation, as well as the positive flower structures mapped through the seismic sections, at depth. This stage was succeeded (or was penecontemporaneous) by the extensional structures related to a (also sinistral) transtensional movement stage, associated to volcanism (Macau, Messejana) and thermal doming processes during the Neogene-Pleistocene time interval. This structural model has direct implications to hydrocarbon exploration and exploitation activities at this sector of the Potiguar Basin and its offshore continuation. The structure of the reservoirs at depth (Açu Formation sandstones of the post-rift section) may be controlled (or at least, strongly influenced) by the deformation geometry and kinematics characterized at the surface. In addition, the deformation event recognized in the Barreiras Formation has an age close to the one postulated for the oil maturation and migration in the basin, between the Oligocene to the Miocene. In this way, the described structural cenario represents a valid model to understand the conditions of hydrocarbon transport and acummulation through space openings, trap formation and destruction. This model is potentially applicable to the NW region of the Potiguar Basin and other sectors with a similar structural setting, along the brazilian Equatorial Atlantic Margin

Limites e evolução geodinâmica do Sistema Jaguaribeano, Província Borborema, Nordeste do Brasil

The studied area is geologically located in the Northern Domain of the Borborema Province (Northeast Brazil), limited to the south by the Patos shear zone. Terranes of the Jaguaribeano system are dominant, flanked by the Piranhas (E and S sides) and Central Ceará (NE side) terranes. Its basement comprises gneiss -migmatite terrains of Paleoproterozoic to Archean age (2.6 to 1.9 Ga old), overprinted by neoproterozoic to cambrian tectonotherma l events. Narrow supracrustal belts ( schist belts) display a 1.6 to 1.8 Ga age, as shown by whole - rock Rb-Sr and zircon U-Pb and Pb/Pb dates in acid metavolcanics which dominate in the lower section of these sequences, and in coeval metaplutonics (granitic augen gneisses). From the stratigraphic point of view, three Staterian belts are recognized: 1. Orós Belt - made up by the Orós Group, subdivided in the Santarém (predominantly pure to impure quartzites, micaschists and metacarbonates) and Campo Alegre (metandesites, metabasalts, metarhyolites and metarhyodacites, interlayered with metatuffs and metasediments) formations, and by the Serra do Deserto Magmatic Suite (granitic augen gneisses). 2. Jaguaribe Belt - its lithostratigrahic-lithodemic framework is similar to the one of the Orós Belt, however with a greater expression of the volcano -plutonic components (Campo Alegre Formation and Serra do Deserto Magmatic Suite). The Peixe Gordo Sequence, separately described, is also related to this belt and contain s metasedimentary, metavolcanic (with subordinated volcanoclastics) and metaplutonic units. The first one correlated to the Orós Group and the latter the Serra do Deserto Magmatic Suite. 3. Western Potiguar Belt - represented by the Serra de São José Gro up, subdivided in the Catolezinho (biotite -amphibole gneisses with intercalations of metacarbonates, calcsilicate rocks, amphibolites and quartzite beds to the top) and Minhuins (quartzites, micaschists, metaconglomerates, calcsilicate rocks, acid to the b asic metavolcanics and metatuffs) formations. Its late Paleoproterozoic (Staterian) age was established by a Pb/Pb date on zircons from a granitic orthogneiss of the Catolezinho Formation. The petrographic characteristics and sedimentary structures of the Santarém Formation of the Orós Group point to deltaic to shallow marine depositional systems, overlain by deep water deposits (turbidites). The geodynamic setting of this region encompassed a large depositional basin, probably extending to the east of the Portalegre shear zone and west of the Senador Pompeu shear zone, with possible equivalents in the Jucurutu Formation of the Seridó Belt and in the Ceará Group of central Ceará. The Arneiróz Belt, west Ceará, displays some stratigraphic features and granito ids geochemically akin to the ones of the Orós Belt. The evolutionary setting started with an extensional phase which was more active in the eastern part of this domain (Western Potiguar and part of the Jaguaribe belts), where the rudite and psamite sedime ntation relates to a fluviatile rift environment which evolved to a prograding deltaic system to the west (Orós Group). The basaltic andesitic and rhyolitic volcanics were associated to this extensional phase. During this magmatic event, acid magmas also crystallized at plutonic depths. The Orós Group illustrates the environmental conditions in the western part of this domain. Later on, after a large time gap (1.6 to 1.1 Ga), the region was subjected to an extensional deformational episode marked by 900 Ma old (Sm-Nd data) basic rocks, possibly in connection with the deposition of the Cachoeirinha Group south of the Patos shear zone. In the 800 to 500 Ma age interval, the region was affected by important deformational and metamorphic events coupled with in trusion of granitic rocks of variable size (dykes to batholiths), related to the Brasiliano/Pan -African geotectonic cycle. These events produced structural blocks which differentiate, one from the other, according to the importance of anatectic mobilizatio n, proportion of high-grade supracrustals and the amount of neoproterozoic -cambrian granitoid intrusions. On this basis, a large portion of the Jaguaretama Block/Terrane is relatively well preserved from this late overprint. The border belts of the Jagua retama Block (Western Potiguar and Arneiroz) display kyanite-bearing (medium pressure) mineral associations, while in the inner part of the block there is a north-south metamorphic zoning marked by staurolite or sillimanite peak metamorphic conditions. Regarding the deformations of the Staterian supracrustal rocks, second and third phases were the most important, diagnosed as having developed in a progressive tectonic process. In the general, more vigorous conditions of PT are related to the interval tardi - phase 2 early-phase 3, whose radiometric ages and regional structuring indicators places it in the Brasiliano/Pan-African Cycle. In the Staterian geodynamic setting of Brazilian Platform , these sequences are correlated to the lower Espinhaço Supergroup (p.ex., Rio dos Remédios and Paraguaçu groups, a paleproterozoic rift system in the São Francisco Craton), the Araí and Serra da Mesa groups (north of Goiás, in the so -called Goiás Central Massif), and the Uatumã Group (in the Amazonian Craton). Granitic ( augen gneisses) plutonics are also known from these areas, as for example the A-type granites intrusive in the Araí and Serra da Mesa groups, dated at 1.77 Ga. Gravimetric and geological data place the limits of the Jaguaribeano System (terranes) along the Senador Pompeu Shear Zone (western border) and the Portalegre- Farias Brito shear zone (eastern and southern). However, the same data area not conclusive as regards the interpretation of those structures as suture of the terrane docking process. The main features of those shear zones and of involved lothological associations, appear to favour an intracontinental transpressional -transcurrent regime, during Neoproterozoic-Cambrian times, marking discontinuities along which different crustal blocks were laterally dispersed. Inside of this orogenic system and according to the magnetic data (total field map), the most important terrane boundary appears to be the Jaguaribe shear zone. The geochronological data, on some tectonostratigraphic associations (partly represented by the Ceará and Jucurutu groups), still at a preliminary level, besides the lack of granitic zonation and other petrotectonic criteria, do not allow to propose tectonic terrane assembly diagrams for the studied area

Análise de terrenos na porção setentrional da Província Borborema, NE do Brasil: integração de dados geológicos e gravimétricos

It is presently assumed that the Borborema Province resulted from a complex collisional process associated with the convergent movement of plates, possibly involving amalgamation and accretion of microplates. This process was consolidated at the end of the Brasiliano event. It is investigated the possible limits for the tectonostratigraphic terranes in the northern portion of the province based on an integrated study of geological and gravity data. The study area comprises the portion of the Borborema Province located north of the Patos Lineament, limited by longitudes 33º00 W and 43º29 44"W and latitudes 1º36 S and 8º00 S. A revision of the regional geology allowed to identify areas presenting contrasting geological attributes, possibly representing different terranes whose limits are always shear zones of Brasiliano-age. The Sobral-Pedro II shear zone is the only one undoubtedly presenting geological attributes of sutures zones. The other shear zones are very likely associated with a geodinymic context of accretion, involving oblique collisions (docking), transcurrent and/or transforming sutures, and deep intracrustal shear zones. The gravity data contributed as a tool to identify strong lateral contrasts of density inside the upper crust possibly associated with crustal blocks tectonically juxtaposed. The dominant long wavelength anomaly in the Bouguer anomaly map is an expressive gradient, grossly parallel to the continental margin, caused by density variation across the crust-mantle interface in the transition from the continental crust to the oceanic crust originated by the separation between South America and Africa. Medium to small wavelength anomalies are due to intracrustal heterogeneities such as different Precambrian crustal blocks, Brasiliano-age granites and Mesozoic sedimentary basins. A regional-residual separation of the Bouguer anomaly map was performed in order to enhance in the residual map the effect due to intracrustal heterogeneities. The methodology used for this separation was a robust polinomial fitting. The inversion of residual gravity field resulted in a density contrast map (Δρ), in an equivalent layer that provided more accurated anomalies contours and consolidated the model which the sources of residual anomalies are located in the upper part of the present crust. Based on the coincidence of gravity lineaments in the residual map and Brasiliano shear zones, and using additional geological information, the following shear zones are proposed as limits between terranes: Patos shear zone, Sobral-Pedro II shear zone, Picuí-João Câmara shear zone, Remígio-Pocinhos shear zone, Senador Pompeu shear zone, Tauá shear zone, and Portalegre shear zone. Based on the geological/geophysical information it is attributed a higher level of confidence to the first three proposed limits(Patos, Sobral Pedro II, and Picuí-João Câmara shear zones). From west to east, these shear zones individualize the following terranes: Northwest of Ceará terrane, Central Ceará terrane, Tauá terrane, Orós-Jaguaribe terrane, Seridó terrane, and São José de Campestre terrane. In our study, the Rio Piranhas and Patos terranes are questioned because their previously proposed limits do not present good geological and gravimetric evidences. On the other hand, the previously proposed Cearense terrane is now subdivided into Central Ceará and Tauá terranes. Two residual gravity profiles located in the Seridó belt were interpreted using 2 ½ D direct gravity modeling. The main result of the modeling process is that all anomalies, with the exception of one, can be explained by outcroppring bodies, therefore restricted to the upper part of the present crust

Estruturação litosférica da Província Borborema ao longo da Transecta Angüera (BA) Macau (RN), com base em dados gravimétricos

Since 2005, geophysical surveys have been carried out in the Precambri-an Borborema Province, along two transects with 800 km long each one. A pool of Brazilian public universities and institutions has been acquired deep refrac-tion seismic, gravity and magnetotelluric, with the purpose to model the conti-nental lithosphere of the region. This paper present the gravity survey of the second transect, that crosses the Borborema Province from SW to NE, passing through the São Francisco Craton, Transversal and Meridional zones and Rio Grande do Norte Domain, in the Setentrional Zone. In this way, it cuts some important geologic structures, like the limit of the São Francis Craton and the Borborema Province, Paleozoic and Mesozoic sedimentary basins of Tucano, Jatobá and Potiguar and the extensive Pernambuco and Patos shear zones. Recognition techniques gravity sources in the subsurface, such as spectral analysis and Euler Deconvolution, were applied to the Bouguer anomalies, as well as their regional and residual components. These techniques provided in-formation on possible anomalous bodies, which correlated with pre-existing geological and geophysical data, subsidized a 2.5 D gravity modeling of the lithosphere beneath the Borborema Province and its southern limit with the São Francisco Craton.

Caracterização de reservatórios siliciclásticos neoaptianos: um estudo do membro carmópolis no campo de Camorim, sub-bacia de Sergipe, Brasil

The Camorim Oilfield, discovered in 1970 in the shallow water domain of the Sergipe Sub-basin, produces hydrocarbons from the Carmópolis Member of the Muribeca Formation, the main reservoir interval, interpreted as siliciclastics deposited in an alluvial-fluvial-deltaic context during a late rifting phase of Neoaptian age, in the Sergipe-Alagoas Basin. The structural setting of the field defines different production blocks, being associated to the evolution of the Atalaia High during the rift stage and subsequent reactivations, encompassing NE-SW trending major normal faults and NWEW trending secondary faults. The complexity of this field is related to the strong facies variation due to the interaction between continental and coastal depositional environments, coupled with strata juxtaposition along fault blocks. This study aims to geologically characterize its reservoirs, to provide new insights to well drilling locations in order to increase the recovery factor of the field. Facies analysis based on drill cores and geophysical logs and the 3D interpretation of a seismic volume, provide a high resolution stratigraphic analysis approach to be applied in this geodynamic transitional context between the rift and drift evolutionary stages of the basin. The objective was to define spatial and time relations between production zones and the preferential directions of fluid flow, using isochore maps that represent the external geometry of the deposits and facies distribution maps to characterize the internal heterogeneities of these intervals, identified in a 4th order stratigraphic zoning. This work methodology, integrated in a 3D geological modelling process, will help to optimize well drilling and hydrocarbons production. This methodology may be applied in other reservoirs in tectonic and depositional contexts similar to the one observed at Camorim, for example, the oil fields in the Aracaju High, Sergipe Sub-basin, which together represent the largest volume of oil in place in onshore Brazilian basins

A releitura de um documento: o processo de tombamento do centro histórico de Natal (RN)

During over seven decades of institutionalizing the national heritage protection legal instrument it can be noticed the many ways of the instrument application, according to the approaches that were assigned to the spaces with heritage values and the dynamic of the elaborated thoughts within this theme. For the application of the instrument effectively, there is a long process that is carried out. This process begins with the study elaboration that aims to subsidize and justify the motivation of property protection, as well as the proposal of buffer zones and national protection areas delimitations, completing the process with the denial of the request or with the publication of the definitive national protection area at the Official Gazette. Starting with the relation between the existing heritage values identification into the historical centres and the definition of its protection areas that the area management will be done, based as well into the management intervention norms established for the protection area perimeter. From this context, the present essay has as porpoise to discuss the approach used for the identification and selection of a historical centre liable for national protection and the repercussion of this identification into the national protection area the was established, using a case study of the national protection of the historical centre of the city of Natal. Starting from the assumption that there are inconsistences and distortions about the text speech of the written document and the spatial delimitation of this document, motivated by an area that privileges the edifications rather than the urban space. Beginning with the urban history methodology, we are based on the precepts of Rossi (2011), Lamas (2010) and Cullen (2009) for that space reading, along with what Sant’Anna (2004) defines as “city-document” to make a new reading of this “heritage value space” verifying if the proposed protection area reflects what is defined as motivation for the national protection area process during the recognizing process. Therefore, it is concluded that it is essential that the buffer zones and the national protection areas are aligned with the text presented at the national protection area instruction, so the norms and criteria definition management process are established. We highlight that a site management and the identified values protection become very difficult without a specific law that beacon the decisions that should be taken.

Assistência social ao idoso no município de Natal na proteção social básica: identificando demandas e desafios

Over the past decades, starting mainly in the 1960s, the number of elderly has grown in the country and an aging population is considered a remarkable global phenomenon. Given the speed of this process, this growth has produced different implications for the structure of the social, economic and cultural societies and, as such, constitutes new challenges for public policy, and particularly for the Brazilian social assistance policy. Considering the significant increase aging population in Natal and the challenges of social welfare policy, this research aims to identify and analyze the demands and challenges of Social Assistance Policy in the city of Natal / RN, in particular the access of the elderly to social protection basic in the Reference Centers of Social Assistance. This research uses a critical dialectical method, and the methodological procedures that guided the study: the bibliographical research, documentary and field as well as systematic observation. Some initial questions were important to guide this work: What are the demands that come to CRAS the elderly population? What are the answers to these demands by the Basic Social Protection? How this CRAS has implemented social protection responses to these demands as rights guarantee the elderly population? The services offered by CRAS meets user needs? To get the results of this research, bibliographic sources were used, documentary and observation for four (4) CRAS of different district areas of the city of Natal. The results of this research show that basic social protection is quite fragile, leaving part of the population at risk and social vulnerability still without attention due to several factors, including the reduced technical team and the impossibility of service to all neighborhoods referenced by CRAS in the respective zones, and 50% of elderly assisted arising from spontaneous demands.

Assistência social ao idoso no município de Natal na proteção social básica: identificando demandas e desafios

Over the past decades, starting mainly in the 1960s, the number of elderly has grown in the country and an aging population is considered a remarkable global phenomenon. Given the speed of this process, this growth has produced different implications for the structure of the social, economic and cultural societies and, as such, constitutes new challenges for public policy, and particularly for the Brazilian social assistance policy. Considering the significant increase aging population in Natal and the challenges of social welfare policy, this research aims to identify and analyze the demands and challenges of Social Assistance Policy in the city of Natal / RN, in particular the access of the elderly to social protection basic in the Reference Centers of Social Assistance. This research uses a critical dialectical method, and the methodological procedures that guided the study: the bibliographical research, documentary and field as well as systematic observation. Some initial questions were important to guide this work: What are the demands that come to CRAS the elderly population? What are the answers to these demands by the Basic Social Protection? How this CRAS has implemented social protection responses to these demands as rights guarantee the elderly population? The services offered by CRAS meets user needs? To get the results of this research, bibliographic sources were used, documentary and observation for four (4) CRAS of different district areas of the city of Natal. The results of this research show that basic social protection is quite fragile, leaving part of the population at risk and social vulnerability still without attention due to several factors, including the reduced technical team and the impossibility of service to all neighborhoods referenced by CRAS in the respective zones, and 50% of elderly assisted arising from spontaneous demands.

Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption