Efeito da adição de grafite expandido por microondas nas propriedades térmicas, elétricas e mecânicas de nanocompósitos de matriz epóxi

Epoxy based nanocomposites with 1 wt % and 3 wt % of nanographite were processed by high shear mixing. The nanographite was obtained by chemical (acid intercalation), thermal (microwave expansion) and mechanical (ultrasonic exfoliation) treatments. The mechanical, electrical and thermal behavior of the nanocomposites was determined and evaluated as a function of the percentage of reinforcement. According to the experimental results, the electrical conductivity of epoxy was not altered by the addition of nanographite in the contents evaluated. However, based on the mechanical tests, nanocomposites with addition of 1 wt.% and 3 wt.% of nanographite showed increase in tensile strength of 16,62 % and 3,20 %, respectively, compared to the neat polymer. The smaller increase in mechanical strength of the nanocomposite with 3 wt.% of nanographite was related to the formation of agglomerates. The addition of 1 wt.% and 3 wt.% of nanographite also resulted in a decrease of 6,25 % and 17,60 %, respectively, in the relative density of the material. Thus, the specific strength of the nanocomposites was approximately 33,33 % greater when compared to the neat polymer. The addition of 1 wt.% and 3 wt.% of nanographite in the material increased the mean values of thermal conductivity in 28,33 % and 132,62 %, respectively, combined with a reduction of 26,11 % and 49,80 % in volumetric thermal capacity, respectively. In summary, it has been determined that an addition of nanographite of the order of 1 wt.% and 3 wt.% produced notable elevations in specific strength and thermal conductivity of epoxy

Estudo das propriedades termofísicas com variação da expansibilidade de compósito desenvolvido com matriz PUR-NOP e carga funcional de argilomineral

In this study were conducted experimental procedures for determination of variation of the expandability of rigid polyurethane foam (PUR) from a natural oil polyol (NOP), specifically the Castor oil plant, Ricinus communis, pure and additions of the vermiculite in phase dispersed in different percentage within a range from 0% to 20%, mass replacement. From the information acquired, were defined the parameters for production of bodies of test, plates obtained through controlled expansion, with the final volume fixed. Initially, the plates were subjected to thermal performance tests and evaluated the temperature profiles, to later be extracted samples duly prepared in accordance with the conditions required for each test. Was proceeded then the measurement of the coefficient of thermal conductivity, volumetric capacity heat and thermal diffusivity. The findings values were compared with the results obtained in the tests of thermal performance, contributing to validation of the same. Ultimately, it was investigated the influence that changes in physical-chemical structure of the material had exerted on the variation of thermophysical quantities through gas pycnometry, scanning electron microscopy (SEM) combined with energy dispersive X-ray fluorescence spectroscopy (EDXRF), infrared spectroscopy using Fourier transform (FTIR), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Based on the results obtained was possible to demonstrate that all load percentage analyzed promoted an increase in the potential expansion (PE) of the resin. In production of the plates, the composites with density near at the free expansion presented high contraction during the cure, being the of higher density adopted as definitive standard. In the thermal performance tests, the heating and cooling curves of the different composites had presented symmetry and values very close for lines of the temperature. The results obtained for the thermophysical properties of composites, showed little difference in respect of pure foam. The percentage of open pores and irregularities in the morphology of the composites were proportionate to the increment of vermiculite. In the interaction between the matrix and dispersed phase, there were no chemical transformations in the region of interface and new compounds were not generated. The composites of PUR-NOP and vermiculite presented thermal insulating properties near the foam pure and percentage significantly less plastic in its composition, to the formulation with 10% of load

Estudo do aproveitamento de resíduo de gesso como carga para compósito com matriz de resina expansiva de mamona

In the execution of civil engineering works, either by wasting during the coating of wall or demolition of gypsum walls, the generation of the gypsum waste involves serious environmental concerns. These concerns are increased by the high demand of this raw material in the sector and by the difficulties of proper disposal byproduct generated. In the search for alternatives to minimize this problem, many research works are being conducted, giving emphasis in using gypsum waste as fillers in composites materials in order to improve the acoustic, thermal and mechanical performances. Through empirical testing, it was observed that the crystallization water contained in the residue (CaSO4.2H2O) could act like primary agent in the expanding of the polyurethane foam. Considering that polyurethane produced from vegetable oils are biodegradable synthetic polymers and that are admittedly to represent an alternative to petrochemical synthetic polyurethane, this research consist an analysis of the thermal behavior of a composite whose matrix obtained from a resin derived from the expansive castor oil seed, with loads of 4%, 8%, 12% and 16% of gypsum waste replacing to the polyol prepolymer blend. Contributors to this analysis: a characterization of the raw material through analysis of spectroscopy by Fourier transform infrared (FTIR), chemical analysis by X-Ray Fluorescence (XRF) and mineralogical analysis by X Ray Diffraction (XRD), complemented by thermo gravimetric analysis (TGA). In order to evaluate the thermo physical properties and thermal behavior of the composites manufactured in die closed with expansion contained, were also carried tests to determine the percentage of open pore volume using a gas pycnometer, scanning electronic microscopy (SEM), in addition to testing of flammability and the resistance to contact with hot surfaces. Through the analysis of the results, it appears that it is possible to produce a new material, which few changes in their thermo physical properties and thermal performance, promotes significant changes and attractive to the environment

Plasticidade dependente da experiência induzida por manipulação da matriz extracelular

The primary somatosensory cortex (S1) receives inputs from peripheral tactile receptors and plays a crucial role on many important behaviors. However, the plastic potential of this region is greatly reduced during adulthood, limiting functional recovery after injuries. This fact is due to the presence, in the brain parenchima, of structures and substances that have an inhibitory effect on plasticity, such as chondroitin sulfate proteoglicans (CSP) present in the perineuronal.nets (PNNs) surrounding a subset of neurons. Maturation of PNNs coincide with the closure of critical periods of plasticity in cortical areas, since CSP act to stabilize synaptic contacts. Removal of CSP is proven to be an effective therapeutic approach to restore plasticity and increase the odds of functional recovery after cortical lesion. In the present work, we removed CSP from the sensorimotor cortex of rats to restore plasticity and promote the compensatory morphofunctional regeneration of cortical circuits modified by removal of mystacial vibrissae during the critical period. Treatment with the CSP-digesting enzyme chondroitinase ABC proved efficient to restore plasticity in S1 circuits, as evidenced by morphological rearrangements and functional recovery.

Plasticidade dependente da experiência induzida por manipulação da matriz extracelular

The primary somatosensory cortex (S1) receives inputs from peripheral tactile receptors and plays a crucial role on many important behaviors. However, the plastic potential of this region is greatly reduced during adulthood, limiting functional recovery after injuries. This fact is due to the presence, in the brain parenchima, of structures and substances that have an inhibitory effect on plasticity, such as chondroitin sulfate proteoglicans (CSP) present in the perineuronal.nets (PNNs) surrounding a subset of neurons. Maturation of PNNs coincide with the closure of critical periods of plasticity in cortical areas, since CSP act to stabilize synaptic contacts. Removal of CSP is proven to be an effective therapeutic approach to restore plasticity and increase the odds of functional recovery after cortical lesion. In the present work, we removed CSP from the sensorimotor cortex of rats to restore plasticity and promote the compensatory morphofunctional regeneration of cortical circuits modified by removal of mystacial vibrissae during the critical period. Treatment with the CSP-digesting enzyme chondroitinase ABC proved efficient to restore plasticity in S1 circuits, as evidenced by morphological rearrangements and functional recovery.

Efeito da adição de grafite expandido por microondas nas propriedades térmicas, elétricas e mecânicas de nanocompósitos de matriz epóxi

Epoxy based nanocomposites with 1 wt % and 3 wt % of nanographite were processed by high shear mixing. The nanographite was obtained by chemical (acid intercalation), thermal (microwave expansion) and mechanical (ultrasonic exfoliation) treatments. The mechanical, electrical and thermal behavior of the nanocomposites was determined and evaluated as a function of the percentage of reinforcement. According to the experimental results, the electrical conductivity of epoxy was not altered by the addition of nanographite in the contents evaluated. However, based on the mechanical tests, nanocomposites with addition of 1 wt.% and 3 wt.% of nanographite showed increase in tensile strength of 16,62 % and 3,20 %, respectively, compared to the neat polymer. The smaller increase in mechanical strength of the nanocomposite with 3 wt.% of nanographite was related to the formation of agglomerates. The addition of 1 wt.% and 3 wt.% of nanographite also resulted in a decrease of 6,25 % and 17,60 %, respectively, in the relative density of the material. Thus, the specific strength of the nanocomposites was approximately 33,33 % greater when compared to the neat polymer. The addition of 1 wt.% and 3 wt.% of nanographite in the material increased the mean values of thermal conductivity in 28,33 % and 132,62 %, respectively, combined with a reduction of 26,11 % and 49,80 % in volumetric thermal capacity, respectively. In summary, it has been determined that an addition of nanographite of the order of 1 wt.% and 3 wt.% produced notable elevations in specific strength and thermal conductivity of epoxy

Prevalência de alterações fundoscópicas em estudantes na cidade de Natal/Brasil

Objetivo: Determinar a prevalência de alterações fundoscópicas em estudantes de escolas das redes pública e privada de Natal-RN. Métodos: Avaliação oftalmológica foi realizada em 990 alunos, de 5 a 21 anos, matriculados nas escolas das redes públicas e privada do município de Natal- RN, que estiveram cursando alguma série do ensino fundamental ou médio, no período de 03 a 06 de 2001. Resultados: Alterações fundoscópicas foram observadas em 5,3% dos estudantes. As anormalidades encontradas, por ordem de freqüência, foram: branco sem pressão, 1,0%; cicatriz de retinocoroidite sugestiva de toxoplasmose, 1,0%; atrofia do epitélio pigmentado da retina, 0,8%; nevos da coróide, 0,4%; escavação da cabeça do nervo óptico aumentada, 0,4%; degeneração em treliça, 0,3%; buraco operculado, 0,2%; fundus miópico, 0,2%; tortuosidade vascular aumentada, 0,2%; granuloma sugestivo de toxocaríase, 0,2%; hipoplasia da cabeça do nervo óptico, 0,1%; persistência da artéria hialoidea, 0,1%; persistência de fibras de mielina, 0,1%; retina sal e pimenta, 0,1%; retinosquise, 0,1%. Conclusão: Houve uma baixa prevalência de alterações fundoscópicas na população estudada

Achados da fundoscopia e alterações do pé diabético em pacientes do Hospital Universitário Onofre Lopes/UFRN

Trabalho com o objetivo de identificar as alterações do pé diabético causadas pelas lesões microangiopáticas e das lesões do fundo de olho secundárias aretinopatia diabética. Métodos:76 pacientes com Diabetes Melito tipos 1 e 2atendidos no ambulatório de Oftalmologia e Cirurgia Vascular do HUOL/UFRN, Natal, RN, no período de novembro de 2004 a janeiro de 2005, com queixas relativas a alterações da retinopatia diabéticae/oudo pé diabético. Em todos os pacientes foi realizado exame clínico geral, vascular e oftalmológico. Na avaliação específicado pé diabético deu-se ênfase paraa investigação do status vascular pela Classificação de Fontaine para Doença Arterial Obstrutiva Periférica, biomecânica,e teste do monofilamento de Semmes-Weinstein. O exame oftalmológico constou de refração e fundoscopiaatravés da qual identificou-se as formas clínicas da retinopatia diabética. Os dados foram submetidos à análise estatística das variáveis primárias que consistiu em caracterizar o grupo quanto a idade, tempo de doença, nível de glicose A segunda estratégia da análise dos dados constituiu na realização de testes de associação entrealgumas variáveis secundárias selecionadas. O software utilizado para os testes estatísticos foi o Statistica Versão 5, 1997.Resultado: Dos 76 pacientes diabéticos 97% tinham idade superior a 40 anos. O tempo de doença65% tinham mais de 10 anos. Com relação à glicose 72,72% apresentaram níveis de glicose em jejum acima de 100mg/dl. 55,26% apresentavam algum grau de retinopatia diabética contra 44,74% que não apresentavamesses sinais. Com as alterações do pé diabético, identificou-se 59,93% com lesões com área de predominância isquêmica, enquanto 41,07% tinham ausência de sinais. 58,82% apresentaram área de predominância neuropática, e 41,18% sem sinais de neuropatia. Dos com retinopatia diabética 78,57% tinham comprometimento isquêmico no pé e 47,62% tinham algum grau de neuropatia diabética. Observou-se que a retinopatia diabética não proliferativa, nos seus diversos graus de comprometimento apresentou-se com percentuais em torno de 80% junto às lesões do pé diabético, seja isquêmico ou neuropático. Dos pacientes que tinham retinopatia 60,46% tinham alterações biomecânicas dos pés. Conclusão: Concluiu-se que a RDNP leve foi mais freqüente nas lesões do pé diabético isquêmico, enquanto a RDNP severa mostrou-se mais presente no pé diabético neuropático

Prevalência de alterações fundoscópicas em estudantes na cidade de Natal-Brasil

Objetivo: Determinar a prevalência de alterações fundoscópicas em estudantes de escolas das redes pública e privada de Natal-RN. Métodos: Avaliação oftalmológica foi realizada em 990 alunos, de 5 a 21 anos, matriculados nas escolas das redes públicas e privada do município de Natal-RN, que estiveram cursando alguma série do ensino fundamental ou médio, no período de 03 a 06 de 2001. Resultados: Alterações fundoscópicas foram observadas em 5,3% dos estudantes. As anormalidades encontradas, por ordem de freqüência, foram: branco sem pressão, 1,0%; cicatriz de retinocoroidite sugestiva de toxoplasmose, 1,0%; atrofia do epitélio pigmentado da retina, 0,8%; nevos da coróide, 0,4%; escavação da cabeça do nervo óptico aumentada, 0,4%; degeneração em treliça, 0,3%; buraco operculado, 0,2%; fundus miópico, 0,2%; tortuosidade vascular aumentada, 0,2%; granuloma sugestivo de toxocaríase, 0,2%; hipoplasia da cabeça do nervo óptico, 0,1%; persistência da artéria hialoidea, 0,1%; persistência de fibras de mielina, 0,1%; retina sal e pimenta, 0,1%; retinosquise, 0,1%. Conclusão: Houve uma baixa prevalência de alterações fundoscópicas na população estudada

Estudo da adição de argila expandida na formulação de concretos leves

Lightweight concrete has been the subject of several studies towards the development of new building materials. Emphasis has been given on the particle size effect and nature of aggregates used as raw materials. The present study includes an analysis of the materials that make this kind of concrete, analyzes of mechanical properties such as compressive and tensile strength, in addition to assessments of the interface concrete aggregate/matrix interface, porosity and absorption profile of chloride ions in lightweight concrete based on expanded clay. The experiments were carried out by molding cylindrical samples 100 mm in diameter and 200 mm in height. The dosage experiments were performed without additives or with the addition of minerals: (T1) 1: 2.01: 1.10: 0.78 (T2) 1: 2.00: 1.32 : 0.62 - (T3) 1 :1.93 :1.54: 0.47 (cement : sand : expanded clay 0500 : expanded clay 1506).The water to cement ratio was set to 0.43. Expanded clay minerals with different average particle sizes were used, i.e., 9.5 mm/0500 and 19 mm/1506. The larger aggregate was coated by a glassy layer, yielding lower water absorption characteristics to the concrete. The results showed that the use of light expanded clay aggregates is a technically interesting solution to the production of lightweight concrete for construction applications

Aproveitamento da fibra do epicarpo do coco babaçu em compósito com matriz epóxi: estudo do efeito do tratamento da fibra

Nowadays the environmental issues are increasingly highlighted since the future of humanity is dependent on the actions taken by man. Major efforts are being expended in pursuit of knowledge and alternatives to promote sustainable development without compromising the environment. In recent years there has been a marked growth in the development of reinforced composite fiber plants, as an alternative for economic and ecological effects, especially in the substitution of synthetic materials such as reinforcement material in composites. In this current study the chemical- physical or (thermophysics )characteristics of the babassu coconut fiber, derived from the epicarp of the fruit (Orbignyda Phalerata), which the main constituents of the fiber: Klason lignin, insoluble, cellulose, holocellulose, hemicellulose and the content of ash and moisture will be determined. A study was conducted about the superficial modification of the fibers of the epicarp babassu coconut under the influence of chemical treatment by alkalinization, in an aqueous solution of NaOH to 2.5% (m/v) and to 5.0% to improve the compatibility matrix / reinforcement composite with epoxy matrix. The results of the changes occurred in staple fibers through the use of the techniques of thermogravimetric analyses (TG) and differential scanning calorimetry (DSC). The results found on thermal analysis on samples of fiber without chemical treatment (alkalinities), and on fiber samples treated by alkalinization show that the proposed chemical treatment increases the thermal stability of the fibers and provides a growth of the surface of area fibers, parameters that enhance adhesion fiber / composite. The findings were evaluated and compared with published results from other vegetable fibers, showing that the use of babassu coconut fibers has technical and economic potential for its use as reinforcement in composites

Adição de nanopartículas de Ti em matriz de Fe através da deposição por magnetron sputtering

Microalloyed steels constitute a specific class of steel with low amount of carbon and microalloying elements such as Vanadium (V), Niobium (Nb) and Titanium (Ti). The development and application of microalloyed steels and steels in general are limited to the handling of powders with particles of submicron or nanometer dimensions. Therefore, this work presents an alternative in order to construction of microalloyed steels utilizing the deposition by magnetron sputtering technique as a microalloying element addiction in which Ti nanoparticles are dispersed in an iron matrix. The advantage of that technique in relation to the conventional metallurgical processes is the possibility of uniformly disperse the microalloying elements in the iron matrix. It was carried out deposition of Ti onto Fe powder in high CH4, H2, Ar plasma atmosphere, with two deposition times. After the deposition, the iron powder with nanoparticles of Ti dispersed distributed, were compacted and sintered at 1120 ° C in resistive furnace. Characterization techniques utilized in the samples of powder before and after deposition of Ti were Granulometry, Scanning Electron Microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (DRX). In the case of sintered samples, it was carried out characterization by SEM and Vickers Microhardness assays. The results show which the deposition technique by magnetron sputtering is practicable in the dispersion of particles in iron matrix. The EDX microanalysis detected higher percentages of Ti when the deposition were carried out with the inert gas and when the deposition process was carried out with reactive gas. The presence of titanium in iron matrix was also evidenced by the results of X-ray diffraction peaks that showed shifts in the network matrix. Given these results it can be said that the technique of magnetron sputtering deposition is feasible in the dispersion of nanoparticles of iron matrix in Ti.

Tratamentos de fibras de carnaúba [copernicia prunífera (miller) h. e. moore] para o desenvolvimento de compósito biodegradável com matriz de polihidroxibutirato

The use of raw materials from renewable sources for production of materials has been the subject of several studies and researches, because of its potential to substitute petrochemical-based materials. The addition of natural fibers to polymers represents an alternative in the partial or total replacement of glass fibers in composites. In this work, carnauba leaf fibers were used in the production of biodegradable composites with polyhydroxybutyrate (PHB) matrix. To improve the interfacial properties fiber / matrix were studied four chemical treatments to the fibers..The effect of the different chemical treatments on the morphological, physical, chemical and mechanical properties of the fibers and composites were investigated by scanning electron microscopy (SEM), infrared spectroscopy, X-ray diffraction, tensile and flexural tests, dynamic mechanical analysis (DMA), thermogravimetry (TGA) and diferential scanning calorimetry (DSC). The results of tensile tests indicated an increase in tensile strength of the composites after the chemical treatment of the fibers, with best results for the hydrogen peroxide treated fibers, even though the tensile strength of fibers was slightly reduced. This suggests a better interaction fiber/matrix which was also observed by SEM fractographs. The glass transition temperature (Tg) was reduced for all composites compared to the pure polymer which can be attributed to the absorption of solvents, moisture and other low molecular weight molecules by the fibers

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Comportamento da adição do carbeto de nióbio (nBC) na matriz metálica do aço ferrítico 15kH2mfa

The 15Kh2MFA steel is a kind of Cr-Mo-V family steels and can be used in turbines for energy generation, pressure vessels, nuclear reactors or applications where the range of temperature that the material works is between 250 to 450°C. To improve the properties of these steels increasing the service temperature and the thermal stability is add a second particle phase. These particles can be oxides, carbides, nitrites or even solid solution of some chemical elements. On this way, this work aim to study the effect of addition of 3wt% of niobium carbide in the metallic matrix of 15Kh2MFA steel. Powder metallurgy was the route employed to produce this metallic matrix composite. Two different milling conditions were performed. Condition 1: milling of pure 15Kh2MFA steel and condition 2: milling of 15Kh2MFA steel with addition of niobium carbide. A high energy milling was carried out during 5 hours. Then, these two powders were sintered in a vacuum furnace (10-4torr) at 1150 and 1250°C during 60 minutes. After sintering the samples were normalized at 950°C per 3 minutes followed by air cooling to obtain a desired microstructure. Results show that the addition of niobium carbide helps to mill faster the particles during the milling when compared with that steel without carbide. At the sintering, the niobium carbide helps to sinter increasing the density of the samples reaching a maximum density of 7.86g/cm³, better than the melted steel as received that was 7,81g/cm³. In spite this good densification, after normalizing, the niobium carbide don t contributed to increase the microhardness. The best microhardness obtained to the steel with niobium carbide was 156HV and to pure 15Kh2MFA steel was 212HV. It happened due when the niobium carbide is added to the steel a pearlitic structure was formed, and the steel without niobium carbide submitted to the same conditions reached a bainitic structure