Estudo da produção de biossurfactantes sintetizados por Pseudomonas aeruginosa AP029-GVIIA utilizando manipueira como fonte de carbono

This study evaluates the biosurfactants production from cassava wastewater, an agro industrial residue, to be used as carbon source. Using a factorial design 24-1 (half fraction), 10 tests were performed using Pseudomonas aeruginosa AP029/GVII-A in submerged batch cultivation in rotating incubator (shaker). The influence of factors (temperature, agitation, aeration ratio and concentration of cultivation medium) at two different levels for the synthesis of the biosurfactant. Samples were collected throughout the cultivation by 132 hours of fermentation were completed. The best outcome was intended by following production through substrate consumption, dry matter, reduction of surface tension (ring method) and emulsification index. The kinetics of microorganism was assessed for the carbon source used. The results showed that the cassava wastewater is a well assimilable substrate for the production of biotensoactive, reaching 91 % of consumption by the micro-organism under study. The growth temperature was found to be one of the leading factors in the synthesis of the metabolite, followed by aeration and also due to the agitation. The best results showed a 30 % reduction in surface tension (% RTS) for the environment, reaching values of 30 mN/m; 3.0 g /L of biomass and emulsifying index greater than 65 %. The metabolite synthesized still remained stable for different salt concentrations (1, 5 and 10 % w/ v) and alkaline pH (8-10).

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Mobilização de reservas e partição de metabólitos durante a germinação da semente e o estabelecimento da plântula em moringa

Seed germination and seedling establishment are critical processes for commercial plantation and depend directly on reserve mobilization as a source of cellular fuels and biosynthetic precursors. In this way, we investigated the coordination among reserve mobilization, metabolite partitioning, and mobilizing enzyme activities in Moringa oleifera Lam (moringa) an oil-seeded species employed in biofuel production. Seeds were germinated under controlled conditions and seedlings were grown hydroponically at a greenhouse. Samples were harvested at 0, 4, 8, 10, 12, 16, and 20 days after imbibition (DAI). The contents of dry mass (DM), neutral lipids (NL), soluble proteins (SP), starch, total soluble sugars (TSS), non-reducing sugars (NRS), and total free amino acids (TFAA) as the activity of isocitrate lyase (ICL), acid proteases, and amylases were determined. The mobilization of storage proteins was initiated during seed germination whereas the mobilization of storage lipids and starch was triggered throughout seedling establishment although all reserves have been depleted until 20 DAI. The partitioning of DM and metabolites to the roots and the shoots was uneven during seedling establishment. Low shoot/root ratio on the basis of DM could be related to the natural occurrence of moringa in drought climates. In the roots, TSS, NRS, and TFAA were accumulated from 12 to 16 DAI and then were consumed until the end of the experiment. In the shoots, TSS and TFAA were consumed in parallel with NRS accumulation from 12 to 20 DAI. The activity of ICL, acid proteases, and amylases was coordinated with the mobilization of lipids, proteins and starch respectively. Thus, we propose that the patterns of reserve mobilization and metabolite partitioning verified in moringa seem distinct from those found to other tree species and may be involved in metabolic strategies to enable environment colonization

Análise da adição de resíduo oriundo do tratamento de esgotos em massa cerâmica utilizada para fabricação de telhas

Sludge of Wastewater Treatment Plants (WTPs) disposal is a problem for any municipality, for this reason the amount of sludge production is now a key issue in selecting treatment methods. It is necessary to investigate new applications for this waste type, due to the restrictions imposed by the environmental organs. The raw materials used in the Red Ceramic, are generally very heterogeneous, for this reason, such materials can tolerate the presence of different types of wastes. In Rio Grande do Norte, the roof tiles production corresponds to 60,61% from the total of ceramic units produced. Due to the importance of the ceramic industry of roof tiles for the state, allied to the environmental problem of the sludge disposal, this work had for objective to verify the possibility of the incorporation of sewage sludge in ceramic body used for production of roof tiles. In the research, sludge originating from drying beds of WTP of the Central Campus from UFRN and clays originating from a ceramic industry from Goianinha/RN were used. The raw materials were characterized by techniques of: analysis of particles distribution by diffraction to laser; real density; consistence limits; chemical analysis by X-ray fluorescence; mineralogical analysis by X-ray diffraction; organic matter; and solids content. Five batches of roof tiles were manufactured in the approximate dosages of 2%, 4%, 6%, 8% and 10%. To evaluate the properties of each final product, tests of water absorption, impermeability, bending strength, leachability and solubility were accomplished. The roof tiles manufactured with sludge presented characteristics similar to the roof tiles without sludge in relation to the environmental risk. The results showed that it is possible to use approximately up to 4% of sludge in ceramic bodies for production of roof tiles. However, it is observed that the high amount of organic matter (71%) present in the sludge is shown as factor that limits the sludge incorporation in ceramic bodies, worsening the quality of the roof tiles. It is necessary the use of mixtures of different raw materials under point of view of the granulometry and of the other chemical and mineralogical properties for the obtaining of a satisfactory mass to the production of ceramic roof tiles

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Análise das propriedades termofísicas, mecânicas e geométricas de telhas cerâmicas queimadas em forno caieira e forno abóbada

In the industry of ceramic in Rio G. do Norte, tile stands out as the most manufactured product by this industry, being the intermittent kiln abóbada and caieira the principal type of kiln used in burning. There was a need to make a study of the influence exerted by the type of kiln in which tiles are burnt in their thermo physical properties. The analysis started with 24 raw samples of tile, which was split in two groups of 12 samples and burnt in Abóbada and Caieira kiln. Besides that, it was made study of the tax of heat transfer to the environment (for each kiln). After having been burnt the samples were taken for laboratory analysis. The properties verified were impermeability, determination of dry mass, absorption of water, the load of bending rupture and its geometric characteristics, the tests were conducted following the currents standards. The tests were carried out according to the ABNT - NBR 15310. The calculation of the rate of heat transfer showed that the abóbada kiln is more efficient than the Caieira, however the results of tests on the samples revealed no superiority of one over another sample. So the furnace had no influence on the performance of the ceramic tiles

Análise comparativa entre propriedades mecânicas, termofísicas e geométricas de tijolos produzidos pelos fornos caieira e abóbada

In the State of Rio Grande do Norte potteries are distributed in several counties in the four meso, which are: West Potiguar, Center Potiguar, Agreste Potiguar and East Portiguar. The ceramics, mostly, are responsible for products used in construction as bricks, tiles and white brick and wood used as fuel. This paper had a primary focus in the region of Seridó. The furnaces in this region, used to manufacture bricks are configured Caieira and Valt, in most of them using principles rustic, usually operated in an empirical way, using principles of control rather primitive, predominantly visual control. The focus of this study was to analyze the differences in the thermophysical, mechanical and geometric characteristics of bricks produced by Caieira and vault furnaces, using the NBR 15720 and the evaluation of energy efficiency in both furnaces. Thermophysical characteristics were analyzed through tests to determine the water absorption obtained from the difference between dry mass and wet mass of the sample and analysis of the thermal gradient, the mechanical characteristics from determination of the compressive strength of ceramic brick popularly known as bricks and also analyzed the geometrical characteristics of the bricks in order to verify the homogeneity of manufacturing. The tests showed that the energy difference of the two furnaces is not considered responsible for a significant difference in the properties of the products

Otimização da extração de polissacarídeos sulfatados da alga vermelha Gracilaria birdiae e análise da atividade anticoagulante e antioxidante

The sulfated polysaccharides (SP) from the edible red seaweed Gracilaria birdiae were obtained using five different condition extraction (GB1: Water; GB1p: Water/proteolysis; GB1s: Water/sonication; GB1sp: Water/sonication/proteolysis; GB2s: NaOH/sonication; GB2sp: NaOH/sonication/proteolysis. The yield (g) increased in the following order GB2sp>GB1sp>GB1p>GB2s>GB1s>GB1. However, the amount of SP extracted increased in different way GB2sp>GB1p>GB1>GB1sp>GB1s>GB2s. Infrared and electrophoresis analysis showed that all conditions extracted the same SP. In addition, monosaccharide composition showed that ultrasound promotes the extraction of other polysaccharides than SP. In the prothrombin time (PT) test, which evaluates the extrinsic coagulation pathway, none of the samples showed anticoagulant activity. While in the activated partial thromboplastin time (aPTT) test, which evaluates the intrinsic coagulation pathway, all samples showed anticoagulant activity, except GB2s. The aPTT activity decreased in the order of GB1sp>GB2sp>GB1p>GB1>GB1s>GB2s. Total capacity antioxidant (TCA) of the SP was also affected by condition extraction, since GB2s and GB1 showed lower activity in comparison to the other conditions. In conclusion, the conditions of SP extraction influence their biological activities and chemical composition. The data showed NaOH/sonication/proteolysis was the best condition to extract anticoagulant and antioxidant SPs from Gracilaria birdiae.

Avaliação da compactação do solo no crescimento inicial de espécies florestais da caatinga

Despite the importance of the study of roots, little is known about the negative effects of soil compaction in the development of the Caatinga forest species. In this sense, the objective was to evaluate the initial growth of Mimosa caesalpiniifolia, Tabebuia caraiba and Erythina velutina in soil under varying levels of compression. The experiment was conducted in a greenhouse located at the Academic Unit Specialized in Agricultural Sciences, UFRN. To perform the experiment, was used Oxisoil of sandy loam texture, from forest trial Area Agricultural School of Jundiaí (EAJ) of the municipality of Macaíba-RN, in an experimental unit consisting of three overlapping PVC rings, 10 cm in diameter and 25 cm in height, with a central ring which has undergone compression. The experimental design was a randomized block with six replications, being tested four levels of soil compaction (1.35; 1.45; 1.60 and 1.80 kg.dm-³), evaluating the following variables: diameter, height, number of leaves, dry weight of shoot and root system in each layer of the vessels. Overall, the species M. caesalpiniifolia, T. caraiba and E. velutina had initial growth favored by treatment consists of uncompressed soil. The M. caesalpiniifolia and T. caraiba species proved relatively resistant to compaction of the soil does not undergo any significant reduction in root growth density equal to or less than 1.60 kg.dm-³, whereas E. velutina proved susceptible effects of soil compaction, with significant changes in root growth under soil densities equal to or greater than 1.45 kg.dm-³. Increased soil compaction caused the impediment to the expansion of taproot inside the experimental units, promoting the accumulation of roots in the upper layers of the soil for the studied species. The subsoil physical impediment changed the initial aerial growth of M. caesalpiniifolia and E. velutina, but did not influence the growth of air T. caraiba seedlings the tested compression levels.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Testes para a avaliação da qualidade fisiológica de sementes de Moringa oleifera Lam

The evaluation of seed vigor is an important factor for detection of lots of high quality seeds, so that development of procedures to evaluate the physiological potential has been an important tool in quality control programs seeds. In this sense the study aimed to adapt the methodologies of accelerated aging, electrical conductivity and potassium leaching to evaluate Moringa oleifera seed vigor LAM.. Therefore, four lots of moringa seeds were subjected to the germination tests, seedling emergence, speed of emergence index, emergence first count, length and dry mass of seedlings and cold test for their physiological characterization, in addition to accelerated aging, electrical conductivity and potassium leaching. The experimental design was completely randomized with four replications of 50 seeds and the means compared by Tukey test at 5% probability. For accelerated aging the periods were studied aging 12, 24 and 72 hours at 40, 42 and 45°C. For the electrical conductivity test was used to a temperature of 25°C for periods of 4, 8, 12, 16 and 24 hours of immersion in 75 to 125 mL of distilled water, using 25 to 50 seeds, and for potassium leaching test samples were used 25 to 50 seeds, placed in plastic cups containing 70 and 100 mL of distilled water at 25°C for periods of 1, 2, 3, 4, 5 and 6 hours. From the results obtained, it can be inferred that the methods best fit for the accelerated aging test Moringa seeds were a temperature of 40°C for 12 to 72 hours, 42°C 72 hours 45°C 24 hours . In the electrical conductivity test Moringa seeds, the combination of 50 seeds in 75 mL distilled water for a period of immersion of 4 hours and 50 seeds in 125 mL of 4 hours were efficient for the differentiation of lots of Moringa seeds as to vigor and for potassium leaching test moringa seeds, the combination of 50 seeds in 100mL of distilled water allowed the separation of lots of four levels of vigor, at 2 hours of immersion, showing promise in evaluate the quality of moringa seeds.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Análise de microestrutura e de características geotécnicas de misturas de resíduo de polimento de porcelanato e solo

Brazil is a country in development, rich in natural resources. In order to grow sustainably, it is necessary to Brazil to preserve its environment, which is an expressive challenge, especially to industries, such as those producing ceramic materials. This study was developed using Porcelain Tile Polishing Residue (RPP) in blends with soil to build compacted fills. This residue is a slurry generated during the polishing process of porcelain tiles and contains powdery material from the polished tile, the abrasives used during the process and cooling water. The RPP was collected from a private company located in Conde/PB and it was mixed with a sandy-clayey soil, to build the fills. Laboratorial tests were conducted with pure soil, pure RPP and blends in proportions of 5%, 10%, 15% and 20% of RPP in addition to the dry mass of pure soil. The Chemical and Physical Characterization tests performed were: specific solid weight, grain size distribution, laser analysis of grain size distribution, Atterberg limits, X ray fluorescence, X ray diffraction, scanning electron microscopy and soil compaction,. The materials and blends were also compacted and direct shear tests and plate load tests were performed. Plate load tests were conducted using a circular plate with 30 cm diameter, on specimens of pure soil and 5% blend, compacted in a metallic box inside the Soil Mechanics Laboratory of the Federal University of Rio Grande do Norte, Brazil. Both mechanical tests performed were conducted under inundated conditions, willing to reduce the influence of soil suction. An evaluation of the results of the tests performed shows that RPP is a fine material, with grain size distribution smaller than 0,015mm, composed mainly of silica and alumina, and particles in angular shape. The soil was characterized as a clayey sand, geologically known as a lateritic soil, with high percentages of alumina and iron oxide, and particles with rounded shape. Both the Soil and the blends presented low plasticity, while the residue showed a medium plasticity. Direct shear tests showed that the addition of RPP did not cause major changes into blends’ friction angle data, however, it was possible to note that, for the proportions studied, that is a tendency of obtain lower shear stresses for higher percentages of RPP in the blends. Both pure soil and 5% mixture showed a punching disruption for the Plate load test. For this same test, the allowable stress for 5% mixture was 44% higher than the pure soil, and smaller vertical settlement results for all stresses.

Produção de ovinos em pastagem de capim-massai suplementados na estação seca

The low quality of tropical pastures in the dry season justifies the use of dietary supplements to meet the nutritional needs of sheep to meat production. Therefore, the objective of this experiment was to evaluate the agronomic characteristics of massaigrass in the dry season and the effect of protein supplements in the performance and productivity of sheep to meat production grazing. The protein supplements evaluated were: soybean meal, Leucena hay, Gliricidia hay and multiple mixture. The animals were managed in massaigrass pastures under rotational stocking and supplemented daily. Were used 24 sheep ½ Santa Inês x ½ SPRD (without defined breed), males uncastrated, mean age 90 days in a completely randomized design. Performance of sheep was evaluated for average daily gain of live weight gain per area and stocking rate (animals of 25 kg/ha). The pasture was evaluated for forage mass of pre and post-grazing, the percentages of participation of morphological constituents and their nutritional values and rates of herbage accumulation. The total herbage mass decreased throughout the dry season. Crude protein and in vitro digestibility of organic matter of the leaf were higher in the upper 15 cm of the canopy stratum. The average daily weight gain of the animals supplemented with legume hay was similar to that gained by animals supplemented with soybean meal in the four grazing cycles. The total live weight gain of animals supplemented with legume hay was higher than the animals supplemented only with multiple mixing the first two grazing cycles. Hays of Leucena and Gliricidia can be given for supplementation of sheep maintained on pasture

Gênero ou sexualidade?: (re) produção das identidades homoeróticas masculinas no cinema de massa

Homosexuality has been gaining strength in Cinema from the late twentieth century, when there is a dissemination of freedoms around the peripheral or marginal sexualities. Based on this assumption, it was formulated in the dissertation work, an analysis of the relationship between Cinema and Sexuality in order to understand, describe, reflect and analyze possible changes around the performative behaviors of male homosexual from the introduction of them in film production, arising from the mass culture industry. These productions are located in three different decades. In this case, the Cinema has not only the reproductive character of realities, but also a producing agent and consolidating them. The methodology applied was discourse analysis of three film works, namely La Cage aux Folles (1978), In & Out (1997) and Boat Trip (2002). The image, research object of this work, is developed by a mass culture that will produce mass identities which is characterized by crystallization of clichés around the gay world