Análise de falhas em rolamentos por análise de vibração aplicado a aerogeradores

With the heavy use of bearings in various segments of the industry, there are a large number of necessary interruptions in industrial processes to perform maintenance on these devices, with the case study wind turbines. The growth of the wind energy sector, encouraged to conduct research that helps to solve this problem. To contribute to predictive maintenance has been carried out a signal analysis using techniques which allow detection and location of the problem in order to prevent accidents caused and losses due to unexpected equipment failures, whereas low system rotation complicates the detection of the failure. To work around this problem, there was the indication of standard signals for defects in the bearings, making diagnosis of possible failures. With this diagnosis can be performed predictive maintenance, identifying the failure of the system that were tested, such as the introduction of grains of sand in the bearing, wear on the outer race of the bearing and bearing rust. By processing signals it is possible to construct graphs developing a mapping of defects by different peaks in the frequency band.

Manutenção da Heterozigosidade em populações de plantas autógamas

Neste trabalho objetivou-se verificar, teoricamente , a possibilidade de manutenção de heterozigotos, em populações de plantas autógamas, na presença e na ausência de seleção dependente de frequência (SDF). Considerou-se apenas um loco com dois alelos. Utilizou-se a dedução algébrica de formulas referentes a alguns modelos de populações e um programa para simular a sucessão das gerações em uma calculadora científica avançada. Comparou-se os resultados do modelo com os dados obtidos experimentalmente por Allard e Workman (1963) e por Harding, Allard e Smeltzer (1966). Os coeficientes de determinação foram 0,9653 e 0,9166 para a primeira e a segunda comparação, respectivamente. Estes coeficientes indicam que o modelo D representa de modo bastante fidedigno as variações observadas em populações experimentais de plantas predominantemente autógamas

Análise da contribuição de fatores genéticos e ambientais na manutenção da hanseniase nos estados do Rio Grande do Norte e Pará

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Atuação e o conhecimento dos profissionais de enfermagem quanto a morte encefálica e manutenção do potencial doador de órgãos e tecidos para transplantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Comparação entre modelos equivalentes de aerogeradores síncronos utilizando o programa ATP

At present, the electricity generation through wind energy has an importance growing in the world, with the existence of very large plans for future wind power installation worldwide. Thus, the increasing the electricity generation through wind power requires, more and more, analysis of studies of interaction between wind parks and electric power systems. This paper has as purposes to implement equivalent models for synchronous wind generators to represent a wind park in ATP program and to check behavior of the models through simulations. Simulations with applications of faults were achieved to evaluate the behavior of voltages of system for each equivalent model, through comparisons between the results of models proposed, to verify if the differences obtained allows the adoption of the simplest model

Simulação do sistema de esgotamento sanitário de Ponta Negra- Natal: mitigação dos riscos ambientais e estratégia de manutenção preditiva

The simulation of SES-Natal Ponta Negra: mitigation of environmental risks and predictive maintenance strategy was developed in the context of several operational irregularities in the pumping stations and sewage systems in the system Ponta Negra. Thus, the environmental risks and complaints against the company due to overflows of sewage into the public thoroughfare became common. This neighborhood has shown in recent years an increase of resident higher than the initial expectation of growth. In this sense presumed the large population growth and generation of sewers higher than expected, associated to the use of corrective maintenance and misuse of the system may be the main causes of operational failures occurring in the SES. This study aimed at analyzing the hydraulic behavior of SES Ponta Negrathrough numerical simulation of its operation associated to future scenarios of occupation. The SES Ponta Negra has a long lengthof collection networks and 6 pumping stations interconnected, being EE 1, 2, 4 coastal way, and beach Shopping interconnected EE3 to receives all sewers pumped from the rest pumping station and pumped to the sewage treatment station of neighborhood which consists of a facultative pond followed by three maturation ponds with disposal of treated effluent into infiltration ditches. Oncethey are connected with each other, the study was conducted considering the days and times of higher inflow for all lifts. Furthermore, with the aim of measuring the gatherer network failures were conducted data survey of on the networks. Thephysical and operational survey data was conducted between January/2011 and janeiro/2012. The simulation of the SES was developed with the aim ofdemonstrating its functioning, eithercurrently and in the coming years, based in population estimates and sewage flow. The collected data represents the current framework of the pumping stations of the SES Ponta Negra and served as input to the model developed in MS Excel ® spreadsheet which allowed simulating the behavior of SES in future scenarios. The results of this study show thatBeach Shopping Pumping Station is actually undersized and presents serious functioning problemsthatmay compromise the environmental quality of surrounding area. The other pumping stations of the system will reach itsmaximum capacity between 2013 and 2015, although the EE1 and EE3 demonstrateoperation capacity, even precariously, until 2017. Moreover, it was observed that the misuse of the network system, due to the input of both garbage and stormwater, are major factors of failures that occur in the SES. Finally, it was found that the corrective maintenance appliance, rather than predictive,has proven to beinefficient because of the serious failuresin the system, causing damage to the environment and health risks to users

Controle profissional de biofilme dentário como estratégia para manutenção da saúde periodontal de pacientes com aparelho ortodôntico fixo: análise comparativa entre diferentes períodos

The presence of fixed orthodontics appliances interfere on sanitation, allowing periodontal diseases to appear, despite the fact patients keep on visiting the dentist every month. This research aims to determine a protocol for the mechanical control of the dental biofilm performed by the professional. A protocol that was able to maintain the periodontal health of the patients under orthodontic treatment with fixed appliances, and in order to do so, it used a non-controlled, randomized and blind clinical essay. The sample involved 40 adolescents who were under the installation of fixed orthodontics appliances and it was divided in three groups, as follows: monthly controlled group (group 1) composed of 11 patients, the quarterly controlled group (group 2) with 16 patients and the semestrial controlled group (group 3) with 13 patients. For data collection, an interview and clinical exams with probing depth measurement, quantity of keratinized mucosa, Gingival Index and the Plaque Index were used. On the initial exam all patients received brushing guidelines as well as the professional control of dental biofilm, with periodontal scaler, Robinson s brush and prophylactic paste. However, Group 1 returned every month for control procedures; Group 2 every three months and Group 3 after six months. The intervention had a six-month duration (for all the three groups), when all the exams were repeated by another examiner who did not know which group each patient was inserted in. Finally, the research concluded that despite the fact there is no statistically significant difference among the three groups, clinically the patients from the monthly group presented a better response to professional control, with less accumulation of dental biofilm and less rate of gingival inflammation. Thus, the mechanical control of the dental biofilm performed by the professional could not avoid gingival increase, characterized by the raise of probing depth measurement, neither the quantity of keratinized mucosa

Análise da influência do efeito esteira de aerogeradores no microclima na superfície do solo: o caso do parque eólico piloto de Macau/RN

This study aimed to evaluate the microclimate changes surrounding the wind farm Macau Pilot / RN, present in the municipality of the same name. To achieve this goal made use of remote sensing techniques using Landsat - 5 TM and 7 ETM +, from which made it possible evaluation of temperature changes on the surface, this around the park in periods prior to its implementation, to the today. For evaluation of the temperature data that has been generated by applying a template was performed its correlation with field data collection and evaluated the degree of correlation, in order to confirm the validity of the data acquired by satellite. Also held was a characterization of the climate of the region based on the data of this climatological station in Macau. Once collected this data made possible the evaluation of climate change policy in the study region. After validation of the temperature models, an analysis of the generated temperature histograms was performed visually could not identify any significant change. However when analyzing the temperature data at a higher level of detail, a data pattern of behavior was detected for both periods evaluated, yet could not see a distinction between the periods of pre-operation of the park, and post-operation . From this result was levantas hypotheses to explain the behavior of the data, the first of which is the presence of moisture in the soil, and the second to the soil composition. In order to validate the hypotheses were applied PDI techniques, involving a combination of different RGB bands of Landsat 5 and the implementation of Reason bands procedure that might show the elements present on the soil surface.

Manutenção da Heterozigosidade em populações de plantas autógamas

Neste trabalho objetivou-se verificar, teoricamente , a possibilidade de manutenção de heterozigotos, em populações de plantas autógamas, na presença e na ausência de seleção dependente de frequência (SDF). Considerou-se apenas um loco com dois alelos. Utilizou-se a dedução algébrica de formulas referentes a alguns modelos de populações e um programa para simular a sucessão das gerações em uma calculadora científica avançada. Comparou-se os resultados do modelo com os dados obtidos experimentalmente por Allard e Workman (1963) e por Harding, Allard e Smeltzer (1966). Os coeficientes de determinação foram 0,9653 e 0,9166 para a primeira e a segunda comparação, respectivamente. Estes coeficientes indicam que o modelo D representa de modo bastante fidedigno as variações observadas em populações experimentais de plantas predominantemente autógamas

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades