40 resultados para Layer-by-layer technique
em Universidade Federal do Rio Grande do Norte(UFRN)
Resumo:
Micro cracking during service is a critical problem in polymer structures and polymer composite materials. Self-healing materials are able to repair micro cracks, thus their preventing propagation and catastrophic failure of structural components. One of the self-healing approaches presented in the literature involves the use of solvents which react with the polymer. The objective of this research is to investigate a procedure to encapsulate solvents in halloysite nanotubes to promote self-healing ability in epoxy. Healing is triggered by crack propagation through embedded nanotubes in the polymer, which then release the liquid sovent into the crack plane. Two solvents were considered in this work: dimethylsulfoxide (DMSO) and nitrobenzene. The nanotubes were coated using the layer-by-layer technique of oppositely charged polyelectrolytes: cetyltrimethylammonium bromide (CTAB) and sodium polyacrylate. Solvent encapsulation was verified by X-ray diffraction (XRD), Fourier transform infrared (FTIR), analysis thermogravimetry (TGA), adsorption and desorption of nitrogen and scanning electron microscopy (SEM). The introduction of the solvent DMSO into the cavity of the nanotubes was confirmed by the techniques employed. However, was not verified with nitrobenzene only promoted clay aggregation. The results suggest that the CTAB reacted with the halloystite to form a sealing layer on the surface of the nanotubes, thus encapsulating the solvent, while this was not verified using sodium polyacrylate.
Resumo:
This study explores the potential of the simvastatin to ameliorate inflammation and infection in open infected skin wounds of rats. Methods: Fourteen Wistar rats weighing 285±12g were used. The study was done in a group whose open infected skin wounds were treated with topical application of sinvastatina microemulsion (SIM, n=7) and a second group with wounds treated with saline 0.9 % (SAL, n=7). A bacteriological exam of the wounds fluid for gram positive and gram negative bacteria, the tecidual expression of TNFá and IL-1â by imunohistochemical technique, and histological analysis by HE stain were performed. Results: The expression of TNFa could be clearly demonstrated in lower degree in skin wounds treated with simvastatin (668.6 ± 74.7 ìm2) than in saline (2120.0 ± 327.1 ìm2). In comparison, wound tissue from SIM group displayed leukocyte infiltration significantly lower than that observed in SAL group (p<0.05). Culture results of the samples taken from wound fluid on fourth post treatment day revealed wound infection in only one rat of group simvastatin (SIM), where Proteus mirabilis, Escherchia coli and Enterobacter sp were isolated. In the rats whose wounds were treated with saline (SAL), polymicrobial infection with more than 100,000 CFU/g was detected in all the wounds. Conclusion: In addition to its antiinflammatory properties, the protective effects of simvastatin in infected open skin wounds is able to reduce infection and probably has antibacterial action. The potential to treat these wounds with statins to ameliorate inflammation and infection is promising
Resumo:
This dissertation examines the organizational innovation as a nonlinear process, which occurs in a social and political context and, therefore, socially immersed. Examines the case of shrimp in the state of RN, starting from the following problem: although the norteriograndense shrimp occupies the largest producer of farmed shrimp from Brazil, has a series of bottlenecks concerning the generation of industry innovation, concerning the social relationships and policies between the various actors in the network, whether private or public, and its consequences in terms of opportunity and limits generated for the innovative dynamics. The objective of the research is to understand how the social embeddedness of political actors affects norteriograndense shrimp within the context of structural relations, the industry generation of innovation, throughout its technological trajectory . The approach of social embeddedness balances atomised perspectives, undersocialized and oversocialized, of economic action, considering both the human capacity to act as sources of constraint, whose mechanisms are analyzed the structural and political. In methodological terms this is a case study, analyzed from the research literature, documentary and experimental. Primary data were collected through semi-structured interviews and analyzed in depth by the technique of content analysis. Was adopted a longitudinal approach, seeking to understand the phenomenon from the perspective of the subjects, describing it in an inductive process of investigation. After characterizing the sector and defining their technological trajectory, the analysis of the results followed its four stages: (1) Introduction of Technology: 1973-1980, (2) Intensification of Research: 1981-1991, (3) Technological Adaptation, 1992 -2003, (4) Technological Crisis: 2004-2009. A cross-sectional analysis along the evolutionary trajectory revealed the character of structural changes and policies over time, and implications on the generating process of innovation. Note that, the technological limit to which the sector reached requires changes in technology standards, but is more likely that the potiguar shrimp is entering a new phase of his career in technology rather than a new technological paradigm
Resumo:
Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures
Resumo:
The technique of surface coating using magnetron sputtering is one of the most widely used in the surface engineering, for its versatility in obtaining different films as well as in the micro / nanometric thickness control. Among the various process parameters, those related to the active species of the plasma are of the most fundamental importance in the mechanism and kinetics of deposition. In order to identify the active species of the plasma, parameters such as gas flow, pressure and density of electric power were varied during titanium coating on glass substrate. By flowing argon gas of 10, 20, 30, 40 and 50 sccm (cubic centimeters per minute) for each gas flow a sequential scan of the electric current of 0.10, 0.20, 0.30, 0.40 , 0.50 A. The maximum value of 0.50 A was chosen based both on literature data and on limitations of the equipment. The monitoring of plasma species present during the deposition was carried out in situ by the technique of optical emission spectroscopy (OES) through the spectrometer Ocean Optics USB2000 Series. For this purpose, an apparatus was developed to adapt the OES inside the plasma reactor to stay positioned closest to the target. The radiations emitted by the species were detected by an optical fiber placed behind the glass substrate and their intensities as a function of wavelength were, displayed on a monitor screen. The acquisition time for each condition of the plain parameters was related to the minima of spectral lines intensities due to the film formed on the substrate. The intensities of different emission lines of argon and titanium were then analyzed as a function of time, to determine the active species and estimate the thickness of the deposited films. After the deposition, the coated glasses thin films were characterized by optical transmittance through an infrared laser. It was found that the thickness and deposition rate determined by in situ analysis were consistent with the results obtained by laser transmittance
Resumo:
Doped lanthanum chromite ( LaCrO3 ) has been the most common material used as interconnect in solid oxide fuel cells for high temperature ( SOFC-HT ) that enabling the stack of SOFCs. The reduction of the operating temperature, to around 800 º C, of solid oxide fuel cells enabled the use of metallic interconnects as an alternative to ceramic LaCrO3, From the practical point of view, to be a strong candidate for interconnect the material must have good physical and mechanical properties such as resistance to oxidizing and reducing environments, easy manufacture and appropriate thermo-mechanical properties. Thus, a study on the physic-mechanical interconnects La0,8Sr0,2Cr0,92Co0,08O3 ceramics for SOFC -AT obtained by the method of combustion , as well as thermo-mechanical properties of metallic interconnects (AISI 444) covered with La0,8Ca0,2CrO3 by deposition technique by spray-pyrolysis fuel cells for intermediate temperature (IT-SOFCs). The La0,8Sr0,2Cr0,92Co0,08O3 was characterized by X -ray diffraction(XRD) , density and porosity , Vickers hardness (HV) , the flexural strength at room temperature and 900 °C and scanning electron microscopy (SEM). The X -ray diffraction confirmed the phase formation and LaCrO3 and CoCr2O4, in order 6 GPa hardness and mechanical strength at room temperature was 62 MPa ceramic Interconnector. The coated metal interconnects La0,8Ca0,2CrO3 passed the identification by XRD after deposition of the film after the oxidation test. The oxidative behavior showed increased resistance to oxidation of the metal substrate covered by La0,8Ca0,2CrO3 In flexural strength of the coated metal substrate, it was noticed only in the increased room temperature. The a SEM analysis proved the formation of Cr2O3 and (Cr,Mn)3O4 layers on metal substrate and confirmed the stability of the ceramic La0,8 Ca0,2CrO3 film after oxidative test
Resumo:
The oil activity in the Rio Grande do Norte State (RN) is a permanent threat to coastal ecosystems, particularly mangroves, with the possibility of oil spills. In this context, the objective of this study was to evaluate the potential resistance of the mangrove environment of a possible spill. Were selected and isolated microorganisms degrading oil by the technique of enrichment cultures and formation of a bacterial consortium. The kinetic study of the consortium was held in rotary incubator shaken at 150 rpm and 30° C. Samples were taken at intervals of 4 hours for analysis of cell concentration and surface tension. The biodegradation was monitored using two methods of respirometry: manometric (OxiTop-C ®) and conductivimetry, where the biodegradation of oil was estimated indirectly by oxygen consumption and CO2 production, respectively. Furthermore, it was used a full 2² factorial design with triplicate at central point to the runs that used the conductivimetric methodology.. The technique of enrichment cultures allowed to obtain thirteen bacterial strains. Kinetic study of the consortium, we can showed the absence of the lag phase, reaching a maximum cell concentration of 2.55 g / L at 16 h of cultivation and a reduction on surface tension. When we adopted the methodology of OxiTop-C was detected a band indicating biodegradability (1% oil v/v), however when we used the conductivimetry methodology did not observe any band that would indicate effective biodegradation. By monitoring a process of biodegradation is necessary to observe the methodology will be adopted to evaluate the biodegradation process, since for the same conditions adopted different methodologies can produce different results. The oil-degrading isolates from soils of the mangrove estuary Potengi / RN are largely to be used in bioremediation strategies of these places, in the case of a possible oil spill, or it can be used in the treatment of waste oil generated in saline environments, since they are optimized the conditions of the tests so that the efficiency of biodegradation reach the minimum level suggested by the standarts
Resumo:
The increasing use of fossil fuels in line with cities demographic explosion carries out to huge environmental impact in society. For mitigate these social impacts, regulatory requirements have positively influenced the environmental consciousness of society, as well as, the strategic behavior of businesses. Along with this environmental awareness, the regulatory organs have conquered and formulated new laws to control potentially polluting activities, mostly in the gas stations sector. Seeking for increasing market competitiveness, this sector needs to quickly respond to internal and external pressures, adapting to the new standards required in a strategic way to get the Green Badge . Gas stations have incorporated new strategies to attract and retain new customers whom present increasingly social demand. In the social dimension, these projects help the local economy by generating jobs and income distribution. In this survey, the present research aims to align the social, economic and environmental dimensions to set the sustainable performance indicators at Gas Stations sector in the city of Natal/RN. The Sustainable Balanced Scorecard (SBSC) framework was create with a set of indicators for mapping the production process of gas stations. This mapping aimed at identifying operational inefficiencies through multidimensional indicators. To carry out this research, was developed a system for evaluating the sustainability performance with application of Data Envelopment Analysis (DEA) through a quantitative method approach to detect system s efficiency level. In order to understand the systemic complexity, sub organizational processes were analyzed by the technique Network Data Envelopment Analysis (NDEA) figuring their micro activities to identify and diagnose the real causes of overall inefficiency. The sample size comprised 33 Gas stations and the conceptual model included 15 indicators distributed in the three dimensions of sustainability: social, environmental and economic. These three dimensions were measured by means of classical models DEA-CCR input oriented. To unify performance score of individual dimensions, was designed a unique grouping index based upon two means: arithmetic and weighted. After this, another analysis was performed to measure the four perspectives of SBSC: learning and growth, internal processes, customers, and financial, unifying, by averaging the performance scores. NDEA results showed that no company was assessed with excellence in sustainability performance. Some NDEA higher efficiency Gas Stations proved to be inefficient under certain perspectives of SBSC. In the sequence, a comparative sustainable performance and assessment analyzes among the gas station was done, enabling entrepreneurs evaluate their performance in the market competitors. Diagnoses were also obtained to support the decision making of entrepreneurs in improving the management of organizational resources and promote guidelines the regulators. Finally, the average index of sustainable performance was 69.42%, representing the efforts of the environmental suitability of the Gas station. This results point out a significant awareness of this segment, but it still needs further action to enhance sustainability in the long term
Resumo:
This study assessed the level of knowledge, attitude and practice of Pap smear and human papillomavirus (HPV), in addition to analyzing the prevalence of genital HPV infection, Herpes Simplex Type 2 (HSV-2) and Chlamydia trachomatis in teenagers. The study consisted of two approaches, one based only on interviews conducted with adolescents enrolled in public schools or in public health facilities in the city of Natal. The other approach involved only a group of 132 adolescents enrolled among those admitted to two health units in Natal-RN. This second group of participants two specimens were collected for laboratory analysis: one was directed to prepare the blade for the Pap test, and other processed for DNA extraction for molecular analysis, focusing on the detection of HPV, HSV-2 and C . trachomatis. The presence of DNA of the three pathogens was investigated by the technique of polymerase chain reaction (PCR). The presence of each of the three pathogens was analyzed in terms of socio-demographic characteristics, as well as sexual and reproductive activity to identify risk factors for infection and development of lesions of the uterine cervix. The results show that the adolescents in this study had levels of knowledge and attitude very low, both in relation to cytology to HPV as though they have made a reasonable percentage of adequate practice exam and prevention of HPV infection. The overall prevalence of HPV infection was 54.5% and 48.2% in adolescents with normal cytology and 86.4% in those with abnormal cytology. We observed a higher proportion of cases of infection in the age group of 18 to 21. The prevalence of HPV infection was slightly higher among pregnant teenagers. The overall prevalence of HSV-2 infection was 13.6% and 11.8% in women with normal cytology and 22.7% in those with abnormal cytology. A higher proportion of cases of infection was found in the age group from 14 to 17, with a slightly higher prevalence among pregnant women. The C. trachomatis was found with an overall prevalence of 19.7% and 21.8% in adolescents with normal cytology and 9.1% in those with abnormal cytology. The prevailing rate was highest in the age group 18 to 21 years and in nonpregnant
Resumo:
Innumerable studies have focused been reported on the sleep spindles (SS), Sharp Vertex Waves (SVW) and REM, NREM Sleep as indicators interpreting EEG patterns in children. However, Frequency and Amplitud Gradient (FAG) is rarely cited sleep parameter in children,that occurs during NREM Sleep. It was first described by Slater and Torres, in 1979, but has not been routinely evaluated in EEG reports. The aim of this study was to assess the absence of SS, SVW and FAG, as an indication of neurological compromise in children. The sample consisted of 1014 EEGs of children referred to the Clinical Neurophysiology Laboratory, Hospital Universitário de Brasília (HUB), from January 1997 to March 2003, with ages ranging from 3 months to 12 years old, obtained in spontaneous sleep or induced by choral hydrate. The study was transversal and analytical, in which, visual analysis of EEG traces was perfumed individually and independently by two electroencephalographers without prior knowledge of the EEG study or neurological findings. After EEG selection, the investigators analyzed the medical reports in order to define and correlate neurological pattern was classified according to the presence or absence of neurological compromise, as Normal Neurological Pattern (NNP), and Altered Neurological Pattern (ANP) respectively. From the visual analysis of the EEG(s), it was possible to characterize 6 parameters: 1- FAG present (64,1%); 2- FAG absent (35,9%); 3 - normal SS (87,9%); 4 - altered SS s (12,1%); 5 - normal SVW s (95,7%); 6 - altered SVW s (4,3%). The prevalence of well-formed FAG is found in the 3 months to 5 years age group in the children with NNF. FAG was totally absent from the age of 10 years. When comparing the three sleep graphielements, it was observed that SVW and SS were predominant in children with NNF. However, FAG absent was more prevalent in the ANF than in altered SS an SVW. The statistical analysis showed that there is a strong association of FAG absent, with isolated alteration, in ANF patients, in that the prevalence ratio was 6,60. The association becomes stronger when FAG absent + altered SS(s) is considered (RP= 6,68). Chi-square test, corrected by Yates technique, showed a highly significant relation for FAG ρ= 0,00000001, for error X of 5%, or else the 95% confidence interval (ρ<0,05). Thus, the FAG absent were more expressive in ANF patient than altered SS(s) and SVW(s). The association becomes stronger in order to establish a prognostic relation, when the FAG is combined with the SS. The results os this study allow us to affirm that the FAG, when absent at ages ranging from 3 months to 5 years , is an indication of neurological compromise. FAG is an age-dependent EEG parameter and incorporated systematically, in the interpretation criteria of the EEG of children s sleep, not only in the maturational point of view, but also neurological disturbances with encephalic compromise
Desenvolvimento de sistemas magnéticos com potencialidades terapêuticas para vetorização de fármacos
Resumo:
Magnetic targeting is being investigated as a means of local delivery of drugs, combining precision, minimal surgical intervention, and satisfactory concentration of the drug in the target region. In view of these advantages, it is a promising strategy for improving the pharmacological response. Magnetic particles are attracted by a magnetic field gradient, and drugs bound to them can be driven to their site of action by means of the selective application of magnetic field on the desired area. Helicobacter pylori is the commonest chronic bacterial infection. The treatment of choice has commonly been based upon a triple therapy combining two antibiotics and an anti-secretory agent. Furthermore, an extended-release profile is of utmost importance for these formulations. The aim of this work was to develop a magnetic system containing the antibiotic amoxicillin for oral magnetic drug targeting. First, magnetic particles were produced by coprecipitation of iron salts in alkaline medium. The second step was coating the particles and amoxicillin with Eudragit® S-100 by spray-drying technique. The system obtained demonstrated through the characterization studies carried out a possible oral drug delivery system, consisting in magnetite microparticles and amoxicillin, coated with a polymer acid resistant. This system can be used to deliver drugs to the stomach for treatment of infections in this organ. Another important finding in this work is that it opens new prospects to coat magnetic microparticles by the technique of spray-drying.
Resumo:
Known for thousands of years, tuberculosis (TB) is the leading cause of mortality by a single infectious disease due to lack of patient adherence to available treatment regimens, the rising of multidrug resistant strains of TB (MDR-TB) and co-infection with HIV virus. Isoniazid and rifampicin are the most powerful bactericidal agents against M. tuberculosis. Because of that, this couple of drugs becomes unanimity in anti-TB treatment around the world. However, the rifampicin in acidic conditions in the stomach can be degraded rapidly, especially in the presence of isoniazid, which reduces the amount of available drug for absorption, as well as its bioavailability, contributing to the growing resistance to tuberculostatic drugs. Rifampicin is well absorbed in the stomach because of its high solubility between pH 1 and 2 and the gastric absorption of isoniazid is considered poor, therefore it is mostly intestinal. This work has as objective the development of gastro-resistant multiple-systems (granules and pellets) of isoniazid aiming to prevent the contact with rifampicin, with consequent degradation in acid stomach and modulate the release of isoniazid in the intestine. Granules of isoniazid were obtained by wet method using both alcoholic and aqueous solutions of PVP K-30 as aggregating and binder agent, at proportions of 5, 8 and 10%. The influence of the excipients (starch, cellulose or filler default) on the physical and technological properties of the granules was investigated. The pellets were produced by extrusionesferonization technique using isoniazid and microcrystalline cellulose MC 101 (at the proportion of 85:15) and aqueous solution of 1% Methocel as platelet. The pellets presented advantages over granular, such as: higher apparent density, smaller difference between apparent and compaction densities, smoother surface and, especially, smaller friability, and then were coated with an organic solution of Acrycoat L 100 ® in a fluidized bed. Different percentages of coating (15, 25 and 50%) were applied to the pellets which had their behavior evaluated in vitro by dissolution in acidic and basic medium. Rifampicin dissolution in the presence of uncoated and coated isoniazid pellets was evaluated too. The results indicate that the gastro resistance was only achieved with the greatest amount of coating and isoniazid is released successfully in basic step. The amount of rifampicin in the dissolution medium when the isoniazid pellets were not coated was lower than in the presence of enteric release pellets. Therefore, the polymer Acrycoat L 100 ® was efficient for coating with gastro-resistant function and can solve the problem of low bioavailability of rifampicin and help to reduce its dosage
Resumo:
Beta thalassemia arises as a consequence of the reduction (β+, β++, βsilent) or absence (β0) of beta globin chain synthesis and results from a number of mechanisms that lead to genetic defects. The inheritance of beta thalassemia is characterized by the existence of heterozygous individuals, compound heterozygotes, homozygotes and those with coinheritance of beta thalassemia allele and other thalassemias and/or hemoglobin variants. The aim of this study was to perform molecular and laboratory characterization of beta thalassemia in heterozygous and homozygous individuals and in those with coinheritance of S beta thalassemia. A total of 48 individuals were included (35 heterozygotes, 4 homozygotes and 9 S beta thalessemia carriers) referred to the Integrated Laboratory of Clinical Analyses of the Federal University of Rio Grande do Norte (UFRN) and the Hematology Ambulatory Facility of the Dalton Barbosa Cunha Hemocenter (Hemonorte Natal, Brazil). Peripheral blood samples form each patient underwent the following laboratory examinations: erythrogram, hemoglobin electrophoresis at alkaline pH, measurements of Hb A2, Fetal Hb and serum ferritin. DNA was extracted using the illustra blood genomicPrep Mini Spin Kit and molecular characterization was performed by the PCR/RFLP technique, which involves digestion with specific restriction enzymes for IVS-1 nt 1 (G®A), IVS-1 nt 6 (T®C) and codon 39 (CAG®TAG) mutations. Of the 35 heterozygotes, 37.1% showed IVS-1 nt 6 mutation, 42.9% IVS-1 nt 1 and 20% were carriers of other mutations not identified by the technique used. The four homozygous patients presented with the IVS-1 nt 6 mutation, while 66.7% of the individuals with S beta thalassemia had the IVS-1 nt 1 mutation. Codon 39 was not detected in any of the patients investigated. Of the thallasemic alleles found, 40.4% were IVS- 1 nt 1, 40.4% IVS-1 nt 6 and 19.2% were not identified. Laboratory data showed that the heterozygotes exhibited microcytosis and hypochromia, evidenced by MCV ranging from 57 to 75fL and MCH from 15.9 to 23.6 pg. Hemoglobin A2 varied between 3.7 and 7.2%. The homogygotes also showed reduced MCV and MCH and elevated HbA2.. Comparison of laboratory data between heterozygous individuals with IVS-1 nt 1 and IVS-1 nt 6 mutations showed that heterozygotes for the IVS1-1 mutation had significantly lower mean MCV and MCH (p = 0.023 and 0.007, respectively) and significantly higher hemoglobin A2 (p < 0.001) when compared to heterozygotes for the IVS-1 nt 6 mutation. PCR/RFLP was useful in identifying the presence or absence of IVS-1 nt 6, IVS-1 nt 1 and codon 39 mutations in most of the patients investigated here. This is the first study conducted in the state of Rio Grande do Norte, Brazil aimed at identifying beta thalassemia mutations and represents an important contribution to the knowledge regarding the molecular profile of beta thalassemia in our country
Resumo:
Studies report that the pathophysiological mechanism of diabetes complications is associated with increased production of Reactive Oxygen Species (ROS)-induced by hyperglycemia and changes in the capacity the antioxidant defense system. In this sense, the aim of this study was to evaluate changes in the capacity of antioxidant defense system, by evaluating antioxidant status, gene expression and polymorphisms in the genes of GPx1, SOD1 and SOD2 in children, adolescents and young adults with type 1 diabetes. We studied 101 individuals with type 1 diabetes (T1D) and 106 normoglycemic individuals (NG) aged between 6 and 20 years. Individuals with type 1 diabetes were evaluated as a whole group and subdivided according to glycemic control in DM1G good glycemic control and DM1P poor glycemic control. Glycemic and metabolic control was evaluate by serum glucose, glycated hemoglobin, triglycerides, total cholesterol and fractions (HDL and LDL). Renal function was assessed by measurement of serum urea and creatinine and albumin-to-creatinine ratio (ACR) in spot urine. Antioxidant status was evaluate by content of reduced glutathione (GSH) in whole blood and the activity of erythrocyte enzymes glutathione peroxidase (GPx) and superoxide dismutase (SOD). We also analyzed gene expression and gene polymorphisms of GPx1 (rs1050450), SOD1 (rs17881135) and SOD2 (rs4880) by the technique of real-time PCR (Taqman®). Most individuals with DM1 (70.3%) had poor glycemic control (glycated hemoglobin> 8%). Regarding the lipid profile, individuals with type 1 diabetes had significantly elevated total cholesterol (p <0.001) and LDL (p <0.000) compared to NG; for triglycerides only DM1NC group showed significant increase compared to NG. There was an increase in serum urea and RAC of individuals with DM1 compared to NG. Nine individuals with type 1 diabetes showed microalbuminuria (ACR> 30 mg / mg). There was a decrease in GSH content (p = 0.006) and increased erythrocyte GPx activity (p <0.001) and SOD (p <0.001) in DM1 group compared to NG. There was no significant difference in the expression of GPx1 (p = 0.305), SOD1 (.365) and SOD2 (0.385) between NG and DM1. The allele and genotype frequencies of the polymorphisms studied showed no statistically significant difference between the groups DM1 and NG. However, the GPx1 polymorphism showed the influence of erythrocyte enzyme activity. There was a decrease in GPx activity in individuals with type 1 diabetes who had a polymorphic variant T (p = 0.012). DM1 patients with the polymorphic variant G (AG + GG) for polymorphism of SOD2 (rs4880) showed an increase in the RAC (p <0.05). The combined data suggest that glucose control seems to be the predominant factor for the emergence of changes in lipid profile, renal function and antioxidant system, but the presence of the polymorphisms studied may partly contribute to the onset of complications
Resumo:
In recent years, the biosafety has been made possible a new look which are based the conceptions of health and illness process, as well as human needs. This new vision is focused on health vigilance that is referenced specifically in this study to the worker s health. The health of workers is essential for the prevention and control of epidemics and outbreaks of diseases as well as emerging and reemerging diseases. The present study wants to show the importance of biosafety measures for health workers, showing them through the concepts in their daily work. It is also to direct the use of biosafety measures in the care of oncology and hematology patients care, because of its infection susceptibility. OBJECTIVES: To analyze the conceptions of health workers in the biosafety pratice to the patients in oncological and hematological treatment in an oncological institution in Natal / RN, as well as make a socio-demographic profile of these workers and to know their difficulties to adequate biosafety measures. METODOLOGIA: The research is exploratory descriptive with qualitative approach, using the technique of oral history. The use of this technique is justified for the possibility of analyze the conceptions of health workers in the face of biosafety measures. From the definition of analysis categories that have emerged in the study. The categories were: daily work, education, occupational risk and onco-hematological care. The research population was the health workers who provide care to patients in oncological and hematological treatment. The study was conducted in the League against Cancer, in Natal / RN, specifically in the unit Luiz Antonio Hospital. Data collections were conducted from June to August of 2011 and were interviewed sixteen employees who assist in oncology and hematology. Structured interviews were conducted in three shifts, given the prospects of expanding the possibilities of analysis of the biosafety concepts. After data collection, the interviews were analyzed qualitatively by the technique of oral history. This genre, thematic oral history is a modern resource used for preparation of documents, files and studies concerning the social experience of people and groups with the construction of a script prior to the interview moment (MEIHY, 2002). ANALYSIS OF INFORMATION: It was made a reflection about the concepts and practices of professionals who take care of patients in oncology and hematology as well as its relation to biosafety measures. The speech of employees revealed that the adoption has been very supportive of these standards, although some have been highlighted gaps in the understanding of employees in relation to biosafety and the proposed categories. CONCLUSION: The analysis of information showed that biosafety has been cited by employees as an immeasurable benefit to safety and occupational health. And the strengths marks in their understanding were: the excellence of care and safety in occupational diseases risk reduction and infections resulting from their work activities, despite some difficulties in adopting appropriate biosafety standards