Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Síntese enzimática de ésteres de açúcar: surfactantes e polímeros como novos materiais ambientalmente seguros

Sugar esters are substances which possess surfactant, antifungical and bactericidal actions and can be obtained through two renewable sources of raw materials: sugars and vegetable oils. Their excellent biodegradability, allied to lhe fact that they are non toxic, insipid, inodorous, biocompatible, no-ionic, digestible and because they can resist to adverse conditions of temperature, pH and salinity, explain lhe crescent use of these substances in several sections of lhe industry. The objective of this thesis was to synthesize and characterize surfactants and polymers containing sugar branched in their structures, through enzymatic transesterification of vinyl esters and sugars, using alkaline protease from Bacillus subtilis as catalyst, in organic medium (DMF).Three types of sugars were used: L-arabinose, D-glucose and sucrose and two types of vinyl esters: vinyl laurate and vinyl adipate. Aiming to reach high conversions from substrates to products for a possible future large scale industrial production, a serie of variables was optimized, through Design of Experiments (DOE), using Response Surface Methodology (RSM).The investigated variables were: (1) enzyme concentration; (2) molar reason of substrates; (3) water/solvent rale; (4) temperature and (5) time. We obtained six distinct sugar esters: 5-0-lauroyl L-arabinose, 6-0-lauroyl D-glucose, 1'-O-lauroyl sucrose, 5-0-vinyladipoyl L-arabinose, 6-0-vinyladipoyl D-glucose and 1 '-O-vinyladipoyl sucrose, being lhe last three polymerizable. The progress of lhe reaction was monitored by HPLC analysis, through lhe decrease of sugar concentration in comparison to lhe blank. Qualitative analysis by TLC confirmed lhe formation of lhe products. In lhe purification step, two methodologies were adopted: (1) chromatographic column and (2) extraction with hot acetone. The acylation position and lhe chemical structure were determined by 13C-RMN. The polymerization of lhe three vinyl sugar esters was possible, through chemical catalysis, using H2O2 and K2S2O8 as initiators, at 60°C, for 24 hours. IR spectra of lhe monomers and respective polymers were compared revealing lhe disappearance of lhe vinyl group in lhe polymer spectra. The molar weights of lhe polymers were determined by GPC and presented lhe following results: poly (5-0-vinyladipoyl L-arabinose): Mw = 7.2 X 104; PD = 2.48; poly (6-0-vinyladipoyl D-glucose): Mw = 2.7 X 103; PD = 1.75 and poly (1'-O-vinyladipoyl sucrose): Mw = 4.2 X 104; PD = 6.57. The six sugar esters were submitted to superficial tension tests for determination of the critical micelle concentrations (CMC), which varied from 122 to 167 ppm. Finally, a study of applicability of these sugar esters, as lubricants for completion fluids of petroleum wells was' accomplished through comparative analysis of lhe efficiency of these sugar esters, in relation to three commercial lubricants. The products synthesized in this thesis presented equivalent or superior action to lhe tested commercial products

Efeitos de peixes zooplanctívoros e onívoros sobre a resposta de comunidades planctônicas à fertilização por nutrientes

The food chain theory predict that presence of omnivory prevent the trophic cascade and could be a strong stabilizing factor over resource and consumer community dynamics, and that the nutrient enrichment destabilize populations dynamics. Most of the freshwater tropical reservoirs are eutrophic, and strategies that seek improve the water quality through the control of phytoplankton biomass and nutrient input, become essential for the improvement and preservation of water quality. The aim of this study was test the zooplanktivory (when larvae) and omnivory (when young and adult) effects of Nile Tilapia over the structure and dynamics of plankton communities, in addition or absence of nutrients enrichment. For this, one field experiment was performed with a factorial design 2x3 resulting in six treatments: control, without fish and nutrient (C); with omnivorous fish (O); with zooplanktivorous fish (Z); without fish and with enrichment of nutrients (NP); with omnivorous fish and nutrients (ONP); and, with zooplanktivorous fish and nutrients (ZNP). The two planktivory types reduced the zooplankton biomass and increased the phytoplankton biomass, but the omnivory of filter-feeding fish attenuated the trophic cascade magnitude. The fertilization by nutrients increases the nutrient concentrations in water and the phytoplankton biomass, but the effect on zooplankton is dependent of the trophic structure. In a general way, the effects of the fish and nutrient addition were addictive, but significant interactions among those factors were observed in the answer of some zooplankton groups. The effects of omnivorous fish over the temporal variability of phytoplankton and zooplankton biomass were very variable, the increase or reduce in variability of the plankton depending of the level of nutrients and of the analyzed variable. With base in this study, we conclude that the planktivory type exercised by the fish and the concentrations of nutrients in the water affects the force of pelagic trophic cascades and probably the success of biomanipulation programs for the handling of water quality in lakes and tropical reservoirs

Desenvolvimento de sorvete probiótico a base de leite de cabra: estudo da formulação, características físico químicas, sensoriais e viabilidade das bactérias probióticas

This work targetet the caprine ice cream production added with probiotic bacteria Bifidobacterium animalis subsp. lactis. It is divided into two parts. In the first one, four caprine ice cream formulations were evaluated, in which it was used hydrogenated fat (F1 and F3) or fat substitute (F2 and F4) in two different flavors (F1 and F2, passion fruit, F3 and F4, guava). Statistical differences (p<0.05) were detected for their physical-chemical properties, mainly for total solids and fat, but no differences were observed for melting test results. When it went to sensory acceptance, all four ice cream formulations reached high acceptance indexes, mostly formulation F4, which was selected for further studies. In the second part, F4 formulation was prepared with the addition of probiotic bacteria Bifidobacterium animalis subsp. lactis. The growth kinetics was studied and it was observed that the cellular concentration peak was reached after four fermentation hours (10.14 log UFC/g). This time was selected for pre-fermentation procedure and posterior addition at ice cream syrup. In this part of the study, two experimental groups were evaluated: group G1, in which the probiotic addition occurred before the maturation step and group G2, which included a pre-fermentation step and probiotic addition after ice cream maturation. The physical-chemical properties of these two ice cream groups were similar, except for pH, which was higher for group G2 (p<0.05). G1 samples had superior melting rate (3.566 mL/min) and both groups presented microbiological and sanitary results in accordance to current Brazilian legislation. Also, G1 and G2 were considered sensory accepted due to their acceptance indexes higher than 70%. G1 and G2 sensory profiles were similar (p>0.05), and both ice cream samples exhibited high creaminess (6.76 to 6.91) and mouth melting sensation (6.53 to 6.67) scores, while low sandiness scores (0.85 to 0.86) were observed, positive characteristics for this kind of food product. During the first 24 hours after ice cream production, the population of B. animalis subsp. lactis decreased, reaching 7.15 e 6.92 log CFU/g for G1 and G2, respectively. Probiotic bacteria counts fluctuated in ice cream samples during the first 108 days at frozen storage, especially for G2 group. Decreased probiotic viability was observed for G1 samples during the first 35 days of frozen storage, mild variation between 35 and 63 days and stabilized counts were observed after this time. After 21 days at frozen storage, ice cream samples of G1 and G2 groups reached 1.2 x 109 and 1.3 x 109 CFU/portion, respectively. After 108 days under these storage conditions, the survival rate of B. animalis subsp. lactis was 94.26% and 81.10% for G1 and G2 samples, respectively. After simulation of gastroenteric conditions, G2 group reached 9.72 x 105 CFU/portion. Considering the current requirements of Brazilian legislation, which stipulates that functional foods must have minimum probiotic count between 108 and 109 CFU/portion and detectable probiotic bacteria after being submitted to gastroenteric conditions, it is concluded that the ice cream with the addition of Bifidobacterium animalis subsp. lactis made as shown in this work, can be considered as a dairy functional food

Euler e os números pentagonais

The present investigation includes a study of Leonhard Euler and the pentagonal numbers is his article Mirabilibus Proprietatibus Numerorum Pentagonalium - E524. After a brief review of the life and work of Euler, we analyze the mathematical concepts covered in that article as well as its historical context. For this purpose, we explain the concept of figurate numbers, showing its mode of generation, as well as its geometric and algebraic representations. Then, we present a brief history of the search for the Eulerian pentagonal number theorem, based on his correspondence on the subject with Daniel Bernoulli, Nikolaus Bernoulli, Christian Goldbach and Jean Le Rond d'Alembert. At first, Euler states the theorem, but admits that he doesn t know to prove it. Finally, in a letter to Goldbach in 1750, he presents a demonstration, which is published in E541, along with an alternative proof. The expansion of the concept of pentagonal number is then explained and justified by compare the geometric and algebraic representations of the new pentagonal numbers pentagonal numbers with those of traditional pentagonal numbers. Then we explain to the pentagonal number theorem, that is, the fact that the infinite product(1 x)(1 xx)(1 x3)(1 x4)(1 x5)(1 x6)(1 x7)... is equal to the infinite series 1 x1 x2+x5+x7 x12 x15+x22+x26 ..., where the exponents are given by the pentagonal numbers (expanded) and the sign is determined by whether as more or less as the exponent is pentagonal number (traditional or expanded). We also mention that Euler relates the pentagonal number theorem to other parts of mathematics, such as the concept of partitions, generating functions, the theory of infinite products and the sum of divisors. We end with an explanation of Euler s demonstration pentagonal number theorem

Efeito de três tecnicas de alongamento muscular sobre o torque e atividade eletromiográfica

PURPOSE: To examine the acute effects caused by three techniques for stretching the hamstrings muscle on the active concentric peak torque (PT), passive PT and electromyographic activity (EMG). METHODS: Sixty volunteers (mean ± SD age, 22.6 ± 3 years), height 1.64 ± 0.07m and body weight of 58 ± 8.6kg, were randomly allocated into 4 groups of 15 subjects: Control Group (CG) - 5 minutes at rest, Static Stretching Group (SG) - 2 x 30s; Hold-Relax Group (HRG) - 3 x 6s of isometric contraction of hamstrings interspersed by 10s of hamstrings stretching and agonist Hold-Relax Group (AHRG) - 3 x 6s of isometric contraction of the quadriceps interspersed by 10s of hamstrings stretching. Evaluation has been conducted preand post-intervention, which verified the active concentric PT, passive PT EMG activity of IT. The statistical inference was performed by testing intra and inter, significance level at 5%. RESULTS: After intervention, there was a reduction in passive PT on CG, accompanied by a reduction of EMG activity, and an increase in passive PT on SG and AHRG. There was no change in the active concentric PT, or change in EMG activity. CG showed an increase in angle of the PT active, while the other groups showed no change. CONCLUSION: The results suggest that the shortterm stretching: 1) causes acute increase in passive torque, since the muscle does not perform sub-maximal contraction, 2) does not change in electromyographic activity and active torque, ind ependent of the technique

Avaliação in vitro da adesão e proliferação de células mesenquimais do ligamento periodontal humano em diferentes superfícies de titânio

In the last years, many scientific researches in implantology have been focused on alternatives that would provide higher speed and quality in the process of osseointegration. Different treatment methods can be used to modify the topographic and chemical properties of titanium surface in order to optimize the tissue-implant reactions by a positive tissue response. This study aimed to evaluate the adhesion and proliferation of mesenchymal cells from human periodontal ligament on two different titanium surfaces, using cell culture techniques. Grade II titanium discs received different surface treatments, forming two distinct groups: polished and cathodic cage plasma nitriding. Human periodontal ligament mesenchymal cells were cultured on titanium discs in 24-well cell culture plates, at a density of 2 x 104 cells per well, including wells with no discs as positive control. Data obtained by counting the cells that adhered to the titanium surfaces (polished group and cathodic cage group) and to the plastic surface (control group), in the 24, 48 and 72-hour periods after plating, were used to analyze cell adhesion and proliferation and to obtain the cell growing curve in the different groups. The data were submitted to nonparametric analysis and the differences between groups were compared by Kruskal-Wallis and Friedman statistical tests. No statistically significant differences were found in the cells counts between the groups (p>0.05). It was concluded that both treatments produced surfaces compatible with the adhesion and proliferation of human periodontal ligament mesenchymal cells

Utilização de bagaço de caju desidratado e complexo enzimático na ração para codornas japonesas em postura

Given the significant share of food costs of poultry production, it is necessary to use strategies and techniques to maximize the utilization and biological value of the components of the diets, keeping constant or improving animal performance. In this context, seeking partial substitution of corn and the best use of the constituents of the diet, the present study aimed to evaluate the effects of inclusion of cashew pomace dehydrated (BCD) and enzyme complex (EC) in the diet on performance and quality eggs of Japanese quails. A total of 200 Japanese quail at 87 days of age, in 25 cages in a completely randomized design in a factorial 2 x 2 + 1 (two levels of cashew bagasse x two levels of enzymes) + control diet without cashew bagasse totaling five treatments with five replicates of eight birds each repetition. The experiment lasted 84 days, divided into four periods of 21 days. The treatments consisted of T1-Ration Control, T2-ration with 7.5% without EC BCD, T3-ration with 7.5% BCD with CE, T4-Ration with 15% BCD without EC and T5-Feed with 15% of BCD with EC. The enzyme complex (EC) is used fermentation product of Aspergillus niger, and cashew bagasse was obtained from the juice industry, passed through drying and crushing process for producing the bran. The performance and egg quality of quails, and performance variables: feed intake (FI), feed conversion ratio per dozen eggs (CAKDZ) and egg mass (CAMO), egg production (OP% bird / day), average egg weight (PMO) and egg mass (MO), and variables were egg quality, specific gravity (SG), Haugh unit (HU), yolk index, and the relationships between components eggs (%albumen,% yolk and %shell). Data were analyzed with the Statistical SAEG (2007). The 7.5 and 15% of cashew bagasse, independent of the enzyme complex decreased feed intake and improved the average egg weight. The two levels with the addition of EC showed significant differences for feed conversion by egg mass. The 7.5 with the addition of enzyme complex obtained the lowest average feed conversion per dozen eggs. The inclusion of up to 15% of cashew bagasse dehydrated with or without addition of enzyme complex in the diet of Japanese quails not interfere in the internal and external quality of eggs. The 7.5 and 15% BCD without added enzyme complex gave better means for specific gravity. Under conditions in which the experiment was conducted, it can be stated that the inclusion of up to 15% of cashew bagasse dehydrated with added enzyme complex feeding quail is economically viable, with the level of 7.5% with the addition of complex enzyme presented the best economic indices