Desidratação de polpas de frutas pelo método foam-mat

This study aimed to investigate the foam mat drying process of pineapple and mango pulp, as well as to evaluate the final product quality. Initially, the selection of fruit and additives was conducted based on density and stability determinations of mango, seriguela, umbu and pineapple foams. After selecting pineapple and mango for further studies, the fruit pulps and fruit foams were characterized in regard to their physicochemical composition. The temperature (60oC or 70oC) and the foam thickness (4 and 11 mm) were evaluated in accordance to the obtained drying curves and after model adjustment. Mango and pineapple powders obtained at the best process conditions were characterized in regard to their physicochemical composition, solubility, reconstitution time. Yoghurts were prepared with the addition of pineapple and mango powders and they were evaluated for their sensory acceptance. Results show that the best drying rates were achieved by using 70o C and layers 4mm thick for both fruits. The Page model successfully fitted the drying experimental data and it can be used as a predictive model. Pineapple and mango powders showed acid pH, high soluble solids content, low water activity (approx. 0.25), lipids between 1.46% and 2.03%, protein around 2.00%, and ascorbic acid content of 17,73 mg/100g and 14.32 mg/100g, for mango and pineapple, respectively. It was observed higher ascorbic acid retention for pineapple and mango powders processed at 70o C, which would be explained by the lower drying time applied. The fruit powders exhibited high solubility and fast reconstitution in water. The sensory acceptance indexes for yoghurts with the addition of both fruit powders were higher than 70%, which reflect the satisfactory product acceptance

Avaliação da aplicação de modelos para a secagem de pastas e suspensões em leito de jorro com alimentação contínua

This work studies the development, implementation and improvement of a macroscopic model to describe the behavior of the spouted bed dryer with continuous feeding for pastes and suspensions drying. This model is based on the CST model (Freire et al., 2009) and the model of Fernandes (2005), whose theoretical foundation is based on macroscopic mass and heat balances for the three phases involved in the process: gas, liquid and solid. Because this technique is quite relevant, the studies of modeling and simulation of spouted bed drying are essential in the analysis of the process as a whole, because through them it is possible to predict and understand the behavior of the process, which contributes significantly to more efficient project and operation. The development and understanding of the phenomena involved in the drying process can be obtained by comparing the experimental data with those from computer simulations. Such knowledge is critical for choosing properly the process conditions in order to obtain a good drying efficiency. Over the past few years, researches and development of works in the field of pastes and suspensions drying in spouted bed has been gaining ground in Brazil. The Particulate Systems Laboratory at Universidade Federal do Rio Grande do Norte, has been developing several researches and generating a huge collection of experimental data concerning the drying of fruit pulps, vegetables pastes, goat milk and suspensions of agro-industrial residues. From this collection, some data of goat milk and residue from acerola (Malpighia glabra L.) drying were collected. For the first time, these data were used for the development and validation of a model that can describe the behavior of spouted bed dryer. Thus, it was possible to model the dryer and to evaluate the influence of process variables (paste feeding, temperature and flow rate of the drying air) in the drying dynamics. We also performed water evaporation experiments in order to understand and to study the behavior of the dryer wall temperature and the evaporation rate. All these analysis will contribute to future works involving the implementation of control strategies in the pastes and suspensions drying. The results obtained in transient analysis were compared with experimental data indicating that this model well represents the process

Secagem de misturas de polpa de frutas tropicais em leito de jorro

Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C

Estudo da funcionalidade de espécies comestíveis do semiárido nordestino e estratégias para sua utilização como ingredientes para fins alimentícios

The Brazilian caatinga is characterized by low annual rainfall and arid soils. Several cactaceae, either native or adapted species, grow in this semi-arid region, including the prickly pear (Opuntia fícus indica) and facheiro ((Philosocereus pachycladus Ritter) which produce underexploited edible fruits. In addition to these species, the algaroba is a leguminous with little studied technological applications and bioactive potential so far. Therefore, this research aims to investigate the physicochemical, bioactive and functional attributes of the prickly pear and facheiro fruit pulps and the algaroba flour. Specifically, this study approaches the physicochemical characterization, total phenolic compounds (TPC) and the betalain identification and quantification by HPLC-DAD-ESI-MS. It is also investigated the DPPH antioxidant capacity and the antienzymatic activities against alpha-amylase and alphaglucosidase of water and ethanolic extracts of these food material. In order to address their potential to be used as food ingredients, juice blends prepared with mixtures of cajá and prickly pear, biofilms with facheiro and cereal bars with algaroba flour were elaborated and analyzed. The prickly pear fruits presented low acidity and high sugar content when compared to facheiro. The Philosocereus pachycladus Ritter fruits had higher protein and ash content, but the algaroba flour was the species with higher protein and sugar content among all. The algaroba flour also presented outstanding food fiber content, which reveals its potentiality to be used as a natural intestinal regulator. The TPC of water and ethanol extracts ranged from 3.87 to 16.21 mg GAE/100g for algaroba flour, 79.24 to 110.20 GAE/ 100g for prickly pear and 412.23 to 539.14 mg GAE/100g for facheiro. The 70% (w/v) ethanol extract reached the highest DPPH antioxidant activity, which was linearly correlated to its high TPC content. In regard to the enzymatic inhibitory activities, the best performance was observed for the prickly pear extracts which presented a moderate inhibition for both investigated enzymes, but interestingly, no alpha-glucosidase inhibition was observed for facheiro extracts. This work shows, for the first time in the literature, the functional attributes of facheiro fruits, as well as the presence of betacianins and isobetanin in the pulp of this exotic fruit. When it comes to the food products developed here, the sensory attributes that better described the juice blend cajá-prickly pear were sweetness, acidity, color yellow-orange, body, turbidity and cajá flavor. The discriminative test applied for cereal bars produced with and without algaroba revealed that the texture was the only sensory attribute that differed (p<0.05) between these two samples. It was also observed that the addition of facheiro extracts did not influence the visual characteristics of the biofilms. Overall, this work unveils the physicochemical and bioactive attributes of these commercial and technologically underexploited species widely found in the Brazilian caatinga and presents alternatives for their rational use

Um estudo da abundância de lítio, rotação, atividade cromosférica e magnetismo das estrelas análogas e gêmeas solares

The study physical process that control the stellar evolution is strength influenced by several stellar parameters, like as rotational velocity, convective envelope mass deepening, and magnetic field intensity. In this study we analyzed the interconnection of some stellar parameters, as Lithium abundance A(Li), chromospheric activity and magnetic field intensity as well as the variation of these parameters as a function of age, rotational velocity, and the convective envelope mass deepening for a selected sample of solar analogs and twins stars. In particular, we analyzed the convective envelope mass deepening and the dispersion of lithium abundance for these stars. We also studied the evolution of rotation in subgiants stars, because its belong to the following evolutionary stage of solar analogs, and twins stars. For this analyze, we compute evolutionary models with the TGEC code to derive the evolutionary stage, as well as the convective envelope mass deepening, and derive more precisely the stellar mass, and age for this 118 stars. Our Investigation shows a considerable dispersion of lithium abundance for the solar analogs stars. We also realize that this dispersion is not by the convective zone deep, in this way we observed which the scattering of A(Li) can not be explained by classical theories of mixing in the convective zone. In conclusion we have that are necessary extra-mixing process to explain this decrease of Lithium abundance in solar analogs and twins stars. We analyzed the subgiant stars because this are the subsequent evolutionary stage after the solar analogs and twins stars. For this analysis, we compute the rotational period for 30 subgiants stars observed by Co- RoT satellite. For this task we apply two different methods: Lomb-Scargle algorithm, and the Plavchan Periodogram. We apply the TGEC code we compute models with internal distribution of angular momentum to confront the predict results with the models, and the observational results. With this analyze, we showed which solid body rotation models are incompatible with the physical interpretation of observational results. As a result of our study we still concluded that the magnetic field, convective envelope mass deepening, and internal redistribution of angular momentum are essential to explain the evolution of low-mass stars, and its observational characteristics. Based on population synthesis simulation, we concluded that the solar neighborhood presents a considerable quantity of solar twins when compared with the discovered set nowadays. Altogether we foresee the existence around 400 solar analogs in the solar neighborhood (distance of 100 pc). We also study the angular momentum of solar analogs and twins, in this study we concluded that added angular momentum from a Jupiter type planet, putted in the Jupiter position, is not enough to explain the angular momentum predicted by Kraft law (Kraft 1970)

Secagem de misturas de polpa de frutas tropicais em leito de jorro

Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C

Análises físico-químicas de polpas de frutas e avaliação dos seus padrões de identidade e qualidade

The pulps are products that add economic value enjoy the fruits of the surplus productions of the same. Have good market acceptance because of its practicality and diversity of flavors available year round. In order to assess the quality of the fruit pulp through the physical and chemical parameters and the characteristics of manufacturing industry, we analyzed 36 samples of frozen fruit pulp of three brands marketed in RIO Grande do Norte, 14 brand A, 12 of 10 brand B and brand C, which corresponded to 14 different flavors, of which 10 have identity Standards and Quality (ISQ S) established by the Ministério da Agricultura, Pecuária e Abastecimento (MAPA), totaling 27 samples with ISQ s. We conducted the following physicalchemical analyzes on samples of fruit pulp: Total solids, total soluble solids, pH, titratable acidity, total sugars and the determination of ascorbic acid. The percentage of failure for each parameter evaluated was 37, 04% in total soluble solids, 22,22% for total solids and titratable acidity, 7,40% in relation to pH. The total sugars were within the requirements demanded by the MAPA and ascorbic acid content, determined only in the pulp of acerola and cashew, presented a non compliance in the pulp of brand B. The percentage of failures of the pulps with ISQ S was 59% with brand A, B and C accounted for 3,70%, 33,33% and 22,22% respectively. The pulps which have no established atandards such as pineapple pulp, showed similar values between brands and literature data unlike the pulp of plum, jackfruit and tamarind which diverged greatly in parameters such as total solids and total soluble solids. The study demonstrates the need for greater quality control by the producers with respect to raw materials, processing, packing, stored and the importance of ISQ S to establish the flavors have not yet covered by existing legislation, but already highly commercialized

Propriedades físicas de planetas extrasolares

ROTATION is one the most important aspects to be observed in stellar astrophysics. Here we investigate that particularly in stars with planets. This physical parameter supplies information about the distribution of angular momentum in the planetary system, as well as its role on the control of dierent phenomena, including coronal and cromospherical emission and on the ones due of tidal effects. In spite of the continuous solid advances made on the study of the characteristics and properties of planet host stars, the main features of their rotational behavior is are not well established yet. In this context, the present work brings an unprecedented study about the rotation and angular momentum of planet-harbouring stars, as well as the correlation between rotation and stellar and planetary physical properties. Our analysis is based on a sample of 232 extrasolar planets, orbiting 196 stars of dierent luminosity classes and spectral types. In addition to the study of their rotational behavior, the behavior of the physical properties of stars and their orbiting planets was also analyzed, including stellar mass and metallicity, as well as the planetary orbital parameters. As main results we can underline that the rotation of stars with planets present two clear features: stars with Tef lower than about 6000 K have slower rotations, while among stars with Tef > 6000 K we and moderate and fast rotations, though there are a few exceptions. We also show that stars with planets follow mostly the Krafts law, namely < J > / v rot. In this same idea we show that the rotation versus age relation of stars with planets follows, at least qualitatively, the Skumanich and Pace & Pasquini laws. The relation rotation versus orbital period also points for a very interesting result, with planet-harbouring stars with shorter orbital periods present rather enhanced rotation

Remoção de metais utilizando o hexadecanoato de sódio

Industrial activities like mining, electroplating and the oil extraction process, are increasing the levels of heavy metals such as Cu, Fe, Mg and Cd in aquatic ecosystems. This increase is related to the discharge of effluents containing trace of this elements above the maximum allowed by law. Methods such as ion exchange, membrane filtration and chemical precipitation have been studied as a means of treatment of these metals contamination. The precipitation of metals using anionic surfactants derived from carboxylic acids emerged as an alternative for the removal of metals from industrial effluents. The reaction between bivalent ions and these types of surfactants in aqueous solution leads to the formation of metal carboxylates, which can precipitate in the form of flakes and are subsequently removed by a process of decantation or simple filtration. In this work the metals extraction is performed by using the surfactant sodium hexadecanoate as extracting agent. The main purpose was to study the effect of temperature, solution pH, and concentration of surfactant in the metal removal process. The statistical design of the process showed that the process is directly dependent to changes in pH and concentration of surfactant, but inversely proportional and somewhat dependent to temperature variation, with the latter effect being considered negligible in most cases. The individual study of the effect of temperature showed a strong dependence of the process with the Kraft point, both for the surfactant used as extracting agent, as for the surfactant obtained after the reaction of this surfactant with the metal. From data of temperatures and concentrations of the surfactant was possible to calculate the equilibrium constant for the reaction between sodium hexadecanoate and copper ions. Later, thermodynamic parameters were determined, showing that the process is exothermic and spontaneous.