Avaliação da potencialidade dos resíduos de gesso de revestimento incorporados em formulações de massas cerâmicas

In building, during the implementation process of major or even minor works, there is a considerable waste of plaster in the steps of coating, making it is a negative factor because of the loss of these processes constructive remains incorporated into buildings, as component, whose final dimensions are higher than those projected. Another negative factor is the disposal of waste gypsum in inappropriate places, thus contributing to the degradation of environmental quality, due to the leaching of this waste and may trigger the formation of sulfuric acid. Therefore, based on this picture, processing and reuse of waste coating, combined with the ceramics industry, which is a strong potential in the reuse of certain types of waste, promote mutual benefits. Thus the overall objective of this work is to conduct a search with scientific and technological aspects, to determine the effect of the incorporation of the residue of plaster for coating, from the building, the formulation of bodies for red ceramic. The residue of plaster coating was collected and characterized. They were also selected raw materials of two ceramic poles of the state of Rio Grande do Norte and formulations have been made with the intention of obtaining those with the best physical and mechanical properties, the residue was added the percentage of 5%, 10%, 15%, 20%, 25% and 30%, in the best formulation of ceramic industry 1 and, according the properties analyses, 5%, 10% and 15% as the best results of ceramic industry 2. The samples were sintered at temperatures of 850 ºC, 950 °C and 1050 °C, the heating rate of 5 ºC / min with isotherm of two hours. They were submitted to testing technology, such as lineal shrinkage, water absorption, apparent porosity, apparent density and bending resistence. The residue incorporation best results in the formulations of mass in red ceramic, were observed between the temperatures of 850 ºC and 950 ºC, in those formulations that have illite clays and medium plastic in their composition, in the range of 0% to 15% residue incorporated

Efeito da adição de feldspato e/ou resíduo de caulin em formulações à base de argila ilítica

The red pottery industry in Piauí state is well developed and stands out at the national context for the technical quality of its products. The floor and wall tile industry, however, is little developed since the state has only one company that produces red clay-based ceramic tiles. This thesis aims at using the predominantly illitic basic mass of the above mentioned industry, with the addition of feldspar and/or kaolin residue in order to obtain products of higher technical quality. Kaolin residue consists basically of kaolinite, muscovite mica and quartz; the feldspar used was potassic. In this experiment, basic mass (MB) was used for experimental control and fifteen formulations codified as follows: F2, F4, F8, F16, F32, FR2, FR4, FR8, FR16, FR32, R2, R4, R8, R16 and R32. All raw materials were dry-milled, classified, formulated and then humidified to 10% water. Thereafter, test samples were produced by unixial pressing process in a rectangular steel matrix (60.0 x 20.0 x 5.0) mm3 at (25 MPa). They were fired at four temperatures: 1080°C, 1120°C, 1160°C, with a heating rate of 10°C/min during up to 10 min in an electric oven, and the last one in an industrial oven with a peak of 1140°C, aim ing to confirm the results found in laboratory and, finally, technological tests were performed: MEA, RL, AA, PA, TRF and PF. The results revealed that the residue under study can be considered a raw material with large potential in the industry of red clay-based ceramic tiles, since the results found both in laboratory and in the industry have shown that the test samples produced from the formulations with up to 4% feldspar and those produced with up to 8% feldspar and residue permitted a reduction in the water absorption rate and an increase in the mechanical resistance while those samples produced with up to 4% residue had an increase in the mechanical resistance when compared to those produced from the basic mass and that the formulation with 2% feldspar and residue presented the best technological properties, lowering the sintering temperature down to 1120°C

Evolução diagenética e caracterização dos reservatórios da seção devoniana na Bacia do Rio do Peixe-Nordeste do Brasil

The Rio do Peixe Basin represents a main basin of northeastern Brazil and pioneering work positioned the rocks of this basin in the Early Cretaceous. However, a recent study, based on integrated pollen analysis from three wells, found an unprecedented siliciclastic sedimentary section, in the region, of early Devonian age. Therefore, the present study aims a detailed petrographic and petrological analysis of this devonian section, in the Rio do Peixe Basin and proposes a diagenetic evolution, to understand the characteristics of the porous system, identify the main reservoir petrofacies with the main factors impacting on the quality of these rocks as reservoirs and a quick study on the provenance of this section. The petrographic study was based on samples obtained from subsurface and surface. The diagenetic evolution of petrofacies and its identification were based only on subsurface samples and the study of provenance was based on surface samples. The thin sections were prepared from sandstones, pelites and sandstones intercalated with pelites. The original detrital composition for this section is arcosean and the main diagenetic processes that affected these rocks occur in various depths and different conditions, which resulted in extensive diagenetic variety. The following processes were identified: early fracture and healing of grains; albitization of K-feldspar and plagioclase; siderite; precipitation of silica and feldspar; mechanical infiltration of clay and its transformation to illite/esmectite and illite; autigenesis of analcime; dissolution; autigenesis of chlorite; dolomite/ferrous dolomite/anquerite; apatite; calcite; pyrite; titanium minerals and iron oxide-hidroxide. The occurrence of a recently discovered volcanism, in the Rio do Peixe Basin, may have influenced the diagenetic evolution of this section. Three diagenetic stages affected the Devonian section: eo, meso and telodiagenesis. This section is compositionally quite feldspathic, indicating provenance from continental blocks, between transitional continental and uplift of the basement. From this study, we observed a wide heterogeneity in the role of the studied sandstones as reservoirs. Seven petrofacies were identified, taking into account the main diagenetic constituent responsible for the reduction of porosity. It is possible that the loss of original porosity was influenced by intense diagenesis in these rocks, where the main constituent for the loss of porosity are clays minerals, oxides and carbonate cement (calcite and dolomite)

Diagênese e proveniência dos arenitos da tectonossequência Rifte na bacias do Rio do Peixe Araripe, NE do Brasil

This thesis presents diagenetic and provenance studies of sandstones belonging to the Rift Tectonosequence of the Rio do Peixe and Araripe basins. These basins are located in the interior of Northeast Brazil aligned along the Trend-Cariri Potiguar. Their origin is related to the Early Cretaceous rifting event. In terms of lithostratigraphy, the studied section corresponds to the Antenor Navarro, Sousa and Rio Piranhas formations of the Rio do Peixe Basin, and the Missão Velha and Abaiara formations of the Araripe Basin, outcropping in the central-west Cariri Valley. A facies analysis was performed and identified nine distinct sedimentary facies for the Rio de Peixe Basin and ten sedimentary facies for the Araripe Basin, individualized according to the different rock types and their sedimentary structures. These facies associations to led paleoenvironments interpretations and their vertical succession allowed understanding the evolution of the depositional setting during the cronostratigraphic interval studied in these basins. Based on petrographic and diagenetic studies it was possible to characterize the texture and mineralogy of these sandstones, identifying their diagenetic stage and the grain framework provenance. The petrographic study allowed to classify the lithotypes studied in both basins as quartzarenites. Such quartzarenites, in general, are rich in quartz, feldspar and lithic fragment grains, and at accessory levels tourmaline, sphene, zircon, epidote and other mineralogy. The diagenetic history of the studied rocks proved to be very complex, being characterized by a variety mineral of phases that succeeded each other during the eo, meso and telodiagenetic stages. According to the studied formation and the textural and compositional aspects of the rocks, some processes were more or less active, while others were even absent. The eodiagenetic stage is marked by mechanical infiltration of clays and early mechanical compactional processes. The mesodiagenetic phase is characterized by continuity of the mechanical compaction and the beggining of chemical compaction, with quartz and feldspar overgrowths, precipitation of kaolinite, alteration of framework grains to chlorite and illite, and finally, precipitation of opaque minerals. The telodiagenetic stage is represented by the oxidation of some grains, matrix and cements. For the provenance analysis of the studied sandstones were used ternary diagrams whose vertices correspond to the percentage of quartz, feldspar and lithic fragments. This study allowed identifies the source area of these rocks as continental blocks. It was also possible, based on the chemical stability and mineralogical maturity of the rocks, recognize that the Antenor Navarro Formation of the Rio do Peixe Basin, and the upper section of the Missão Velha Formation of Araripe Basin have less maturity and stability when compared with the other studied formations