26 resultados para Exaustão
em Universidade Federal do Rio Grande do Norte(UFRN)
Resumo:
The vehicles are the main mobile sources of carbon monoxide (CO) and unburned hydrocarbons (HC) released into the atmosphere. In the last years the increment of the fleet of vehicles in the municipal district of Natal-RN it is contributing to the increase of the emissions of those pollutants. The study consisted of a statistical analysis of the emissions of CO and HC of a composed sample for 384 vehicles with mechanization Gasoline/CNG or Alcohol/Gasoline/CNG of the municipal district of Natal-RN. The tests were accomplished in vehicles submitted to Vehicular Safety's Inspection, in the facilities of INSPETRANS, Organism of Vehicular Inspection. An partial gases analyzer allowed to measure, for each vehicle, the levels of CO and HC in two conditions of rotation of the motor (900 and 2500 rpm). The statistical analysis accomplished through the STATISTICA software revealed a sensitive reduction in the efficiency of the converters catalytic after 6 years of use with emission average it is of 0,78% of CO and 156 (ppm) of HC, Which represents approximately 4 (four) times the amount of CO and the double of HC in comparison with the newest vehicles. The result of a Student s t-test, suggests strongly that the average of the emissions of HC (152 ppm), at 900 rpm, is 40% larger than at 2500 rpm, for the motor without load. This result reveals that the efficiency of the catalytic conversion is limited kinetically in low engine speeds. The Study also ends that when comparing the emissions of CO and HC considering the influence of the fuels, it was verified that although the emissions of CO starting from CNG are 62% smaller than arising from the gasoline, there are not significant differences among the emissions of HC originating from of CNG and of the gasoline. In synthesis, the results place the current criteria of vehicular inspection, for exhaust gases, in doubt, leading the creation of emission limits of pollutant more rigorous, because the efficiency of the converters catalytic is sensibly reduced starting from 6 years of use. It is also raised the possibility of modifications in the test conditions adopted by the current norms, specifically in the speed engine, have seen that in the condition without load the largest emission indexes were registered in slow march. That fact that allows to suggest the dismissal of the tests in high speed engine, reducing the time of inspection in half and generating economy of fuel
Resumo:
The advancement of nanotechnology in the synthesis and characterisation of nanoparticles (NP's) has played an important role in the development of new technologies for various applications of nano-scale materials that have unique properties. The scientific development in the last decades in the field of nanotechnology has sought ceaselessly, the discovery of new materials for the most diverse applications, such as biomedical areas, chemical, optical, mechanical and textiles. The high bactericidal efficiency of metallic nanoparticles (Au and Ag), among other metals is well known, due to its ability to act in the DNA of fungi, viruses and bacteria, interrupting the process of cellular respiration, making them important means of study, in addition to its ability to protect UVA and UVB. The present work has as its main objective the implementation of an innovative method in the impregnation of nanoparticles of gold in textile substrate, functionalized with chitosan, by a dyeing process by exhaustion, with the control of temperature, time and velocity, thus obtaining microbial characteristics and UV protection. The exhausted substrates with colloidal solutions of NPAu's presented the colours, lilac and red (soybean knits) due to their surface plasmon peak around 520-540 nm. The NPAu's were synthesized chemically, using sodium citrate as a reducing agent and stabilizer. The material was previously cationised with chitosan, a natural polyelectrolyte, with the purpose of functionalising it to enhance the adsorption of colloid, at concentrations of 5, 7, 10 and 20 % of the bonding agent on the weight of the material (OWM). It was also observed, through an experimental design 23 , with 3 central points, which was the best process of exhaustion of the substrates, using the following factors: Time (min.), temperature (OC) and concentration of the colloid (%), having as a response to variable K/S (ABSORBÂNCIA/ Kubelka-Munk) of the fibres. Furthermore, it was evidenced as the best response, the following parameters: concentration 100%, temperature 70 ºC and time 30 minutes. The substrate with NPAu was characterised by XRD; thermal analysis using TGA; microstructural study using SEM/EDS and STEM, thus showing the NP on the surface of the substrate confirming the presence of the metal. The substrates showed higher washing fastness, antibacterial properties and UV radiation protection.
Resumo:
This paper aims to verify the Burnout´s possibilities of incidence, finding the creating dimensions and comparing with the socio-demographics characteristics of the researched professionals. This quantitative-descriptive search has a population of 197 workers of 23 nourishing companies in Rio Grande do Norte. This population is predominantly male, younger than 28 years old, single, relatively instructed (57,07% with complete high school) and having just started their current job since 79% of the interviewees are in the company less than six years. The AUDITORIA DO SISTEMA HUMANO (ASH) model, utilized for investigation and developed for the Spaniards Quijano and Navarro in 1999, has several dimensions about human resources management and the organizational effectiveness, but only makes part of the research in 19 questions Burnout referring. It was used factorial analyses with extraction method, varimax rotation and Kaiser normalization with the intuition to define the creating dimensions of the syndrome, they were evaluated with Cronbach Alpha coefficient after extraction. The dimensions found through the factorial analyses were: emotional exhaustion, physical exhaustion and vitality. The accumulated explanation value reached 65,30% of total variation. The data socio-demographics don t justify the syndrome appearance, because the T test and ANOVA showed irrelevant values. It has been also observed that the founded dimensions were different of the Maslach sociopsychological perspective (emotional exhaustion, depersonalization and low professional realization) allowing comparison with others researches and the possibility to develop new ones with workers from different assistance areas. These new researches are important, since the syndrome refers to chronic labor stress consequences and any professional is favorable to Burnout, harmful to the company as to the collaborators
Resumo:
This research verifies the influence of the self-efficacy level on burnout syndrome incidence in relation to nursing professionals from private hospitals located in the Municipality of Natal, State of Rio Grande do Norte. The nature of the research was descriptive, and the used data analysis method was quantitative which was developed through SPSS computational package, version 17.0. The used instrument for the investigation was Maslach-Burnout Inventory (MBI), and the General Perceived Self-efficacy Scale (GPSES) was applied to a sample formed from 230 nursing professionals. The statistic techniques to data analysis were: frequency analysis; factor analysis; Cronbach.s alpha; Kaiser-Meyer-Olkin test (KMO); Bartlett efericity test; percentual analysis; Spearman rank correlation analysis; and simple regression. The achieved factors from factor analysis of MBI were the same, taking into account the dimensions which Maslach initially suggested to the instrument (emotional exhaustion, lack of personal realization, and depersonalization). However, one highlights that the low internal consistence of the depersonalization dimension can occur from people.s difficulty (caused by cultural aspects) of assuming this attitude in their work environment. Through GSE, it was achieved a factor which confirmed the unidimensionality showed by the author of the instrument. In relation to the syndrome incidence, it was verified that about 50% of the researched sample presented burnout syndrome evidence. Referring to self-efficacy level, about 65% of the researched sample presented low level of self-efficacy, what can be explained by the work characteristics of these professionals. In relation to the self-efficacy influence on the Burnout syndrome, it was verified that self-efficacy can be one of the aspects which influences occupational stress chronification (burnout), mainly to the personal realization dimension. Therefore, the researched hospital organizations need reflect about their attitudes in respect to their professionals, since the numbers showed a dangerous tendency regarding a predisposition to burnout syndrome of their staff, what implies not only a significant amount of individuals who can present high levels of emotional exhaustion, lack of personal realization, and depersonalization, but also the fact that this group presents low level of self-efficacy
Resumo:
Burnout is a psychological syndrome triggered in response to continuous exposure to interpersonal stressors. It is considered a multifactorial construct, which is commonly characterized by three dimensions: emotional exhaustion, dehumanization, and lack of personal accomplishment.This study aimed to verify if the three characteristics of burnout (exhaustion, lack of dehumanization and personal accomplishment) are present in people working as guides Tourism in Natal - RN. It is a descriptive and quantitative study. 109 subjects were surveyed. Data collection was done through the use of questionnaires, the instrument used was the characterization of the Burnout Scale (ECB) created and validated in Brazil by Trocoli and Tamayo (2000). In order to analyze data we used descriptive statistics, analysis of core measures, exploratory and confirmatory factor analysis, reliability analysis, cluster analysis, multiple discriminant and Spearman correlation. Factor analysis identified four factors that explain 58.3% of the total variance. Those factors were named exhaustion, deception, avoidance, and dehumanization. The reliability of the instrument, as measured by Cronbach's Alpha was 0.918, which is considered excellent reliability. The 109 subjects were grouped into three cluster, which had the deception, avoidance, and dehumanization as discriminant. It is possible to conclude that the characteristics of burnout syndrome are present in the studied population where 19 people are on the high level of burnout, moderate in 32 and 56 in the light. The correlations between socio-demographic variables studied and the dimensions of burnout, were few and weak. The variable leave for health reasons in the study appeared to be related to feelings of exhaustion and avoidance behavior appeared related to younger individuals and who work only in the activity of Receptive Tourism Guide. Verification of the incidence of burnout in individuals surveyed suggest the need to adopt intervention strategies are individual, organizational and / or combined
Resumo:
The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA
Resumo:
Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner
Resumo:
This scientific study deals about the oil and natural gas production participation payment impact in the county of Governador Dix-sept Rosado, Rio Grande do Norte, between 1998 to 2004, applied to family income and property. To do so, this analysis focus on the ricardian´s theory exposition which merges from the concept of the mineral income, in concern to the legal establishment of royalties. This paper also shows the world evolution oil exploration, inserting Brazil in this scene as a oil and natural gas producter. It identifies the productive site of oil and natural gas in Rio Grande do Norte as the Potiguar Oil Area, characterizing its components in the demographic, physical and social aspects, to reflect in the focus point of observation which is the Governador Dix-sept Rosado county. The participation payment on oil and natural gas is demonstrated in a qualitative analysis both in Brazil as in Rio Grande do Norte. The payments given to the land owners in this federative unity are shown in the period of analysis of this essay. The study tells, based in a field research, the benefaction impact of the payment to the land owners over the income and property. The family income were highly impacted, causing economic social classes change to some land owners. The property had less or none impact. It was found negative externalities as the income utilization to other county uses, not causing a multiplier effect in the studied county. The fact of the not utilization of the properties on productive investments in order to supply the finite characteristic of oil and this source of royalties, contradicts one of the reasons of its establishment which is the payment for its productive exhaustion of a land resource
Resumo:
The objective of this study was to investigate the elements that contribute to the state of stress which often affects those who embrace the university teaching career, and also to learn whatever strategies professors use to cope with stressing situations in order to develop resilience and a sound exercise of their profession. To the very nature of university teaching belong a variety of attributions, demands and challenges which, together, may contribute to the development of stress. The epistemological principles which guided this research were those of Complex Thinking, which facilitate a deeper comprehension of the human and social phenomena as viewed through the lens of complexity principles: the dialogical principle, the organizational recursivity principle and the hologramatical principle. Fully acknowledging the many difficulties brought about by any attempt that would try to explain human phenomena based only on one theoretical reference, we have elected multi-referentiality as the support for this study, thus being able to dialogue with a variety of authors about the same phenomenon. This was a qualitative research in which questionnaires and interviews were used as instruments for the empirical work. The data has been articulated into categories and subcategories, allowing for a thematic analysis. Participants of the study were seventeen professors from two different colleges in the city of Natal, state of Rio Grande do Norte. Bad working conditions, demands from the institution, student s lack of commitment, long working hours, low salaries, lack of incentives to university teachers, uncertainty concerning timetable and difficulties in proper time administration are the variables that contribute to the stress of professors. Although this is a problem that affects the group as a whole, strategies to cope with it are individually sought and vary from trying to find different leisure options, opening one s heart to colleagues or relatives, individual planning, prayer, rational facing of the situation, to simply giving in to exhaustion. The study has proposed institutional as well as personal actions that may foster a development among professors which takes into account a resilience development in a collective perspective. Also, it shows some articulations that are already under way so that professors may be attended to.
Resumo:
Experiments were performed to study the effect of surface properties of a vertical channel heated by a source of thermal radiation to induce air flow through convection. Two channels (solar chimney prototype) were built with glass plates, forming a structure of truncated pyramidal geometry. We considered two surface finishes: transparent and opaque. Each stack was mounted on a base of thermal energy absorber with a central opening for passage of air, and subjected to heating by a radiant source comprises a bank of incandescent bulbs and were performed field tests. Thermocouples were fixed on the bases and on the walls of chimneys and then connected to a data acquisition system in computer. The air flow within the chimney, the speed and temperature were measured using a hot wire anemometer. Five experiments were performed for each stack in which convective flows were recorded with values ranging from 17 m³ / h and 22 m³ / h and air flow velocities ranging from 0.38 m / s and 0.56 m / s for the laboratory tests and air velocities between 0.6 m/s and 1.1m/s and convective airflows between 650 m³/h and 1150 m³/h for the field tests. The test data were compared to those obtained by semi-empirical equations, which are valid for air flow induced into channels and simulated data from 1st Thermodynamics equation. It was found that the chimney with transparent walls induced more intense convective flows than the chimney with matte finish. Based on the results obtained can be proposed for the implementation of prototype to exhaust fumes, mists, gases, vapors, mists and dusts in industrial environments, to help promote ventilation and air renewal in built environments and for drying materials, fruits and seeds
Resumo:
Nowadays, Brazil has both the greatest goat herd and the greatest goat milk production of South America. The state of Rio Grande do Norte, located in northeast of Brazil, has an average year production of three thousand cubic meters of goat milk in natura. Part of this milk production is homemade and it comes from small farms, which unite in rural cooperatives created to encourage the production and implementation of industrial processes for preservation and processing of milk. Results presented by literature and obtained from preliminary essays in this thesis show that non conventional dryer of spouted bed with inert particles is able to produce powder milk from in natura milk (cattle or goat), with the same quality of spray dryer, however, operating at low cost. The method of drying in spouted bed consists of injecting milk emulsion on the bed of inert particles gushed by hot air. This emulsion covers the particles with a thin film, which dries and is reduced to powder during the circulation of inerts inside the bed. The powder is dragged by exhaustion air and separated in the cyclone. The friction among particles resulted from the particles circulation, encourages high taxes of shear in the thin film of emulsion, breaking the cohesive forces and making this process possible. Studying the drying process and the powder goat milk production in one unit of spouted bed with inert particles, seeing the development of a low cost technological route for powder milk production is the aim of this thesis. The powder milk produced by this route must attend the local demand of food industries which need an intermediate product to be used as a food ingredient (ice-cream, milk candy). In order to reach this aim, this thesis approaches the aspects related to physical, thermodynamics and physic-chemicals characteristics of goat milk, whose complete data are still inexistent in the literature. The properties of materials are of great importance to the project of any process which involves the operations of transportation of movement, heat and mass quantity, such as the dryers which operate in fluid dynamically active regime, like the spouted bed. It was obtained new data related to the goat milk properties in function of concentration of solids and temperature. It is also important to mention the study developed about the kinetic of solids retention in the bed of inert particles during the drying of goat milk. It was found more adequate processes conditions to the proposed technological route to be implemented in small and micro-industries, with simplifications in the system of milk injection as well as in the form of operation of the dryer. Important data were obtained for a posterior stage of this research which involves the v modeling, simulation, control and optimization of the process. The results obtained in this thesis, in relation to process performance as well as to the quality of produced powder milk validate the proposal of using the spouted bed dryer in the production of powder goat milk
Resumo:
Effluent color resulting from textile dyeing processes has been one of the biggest environmental problems faced by the textile industry. In particular, reactive dyes are highly resistant to conventional wastewater treatment methods. New technologies have been contemplated, some of which have been applied in industrial treatment plants, but color removal has not been efficiently attained. Since microemulsion systems provide good results in heavy metals and proteins extraction processes, their use in dyes extraction has been suggested and investigated. In this work, a real textile wastewater from an exhaustion dyebath has been treated, which contains the following reactive dyes: Procion Yellow H-E4R (CI Reactive Yellow 84), Procion Blue H-ERD (CI Reactive Blue 160) and Procion Red H-E3B (CI Reactive Red 120), in addition to auxiliary compounds normally found in dyeing processes with reactive dyes. The dyes Remazol Blue RR and Remazol Turquoise Blue G (Reactive Blue 21) have also been examined in view of the presence of heavy metals in these molecules. The microemulsion system comprised dodecyl ammonium chloride (as a cationic surfactant), water or wastewater as aqueous phase, kerosene as oil phase, and one of the following alcohols as cosurfactant: isoamyl alcohol, n-butyl alcohol and n-octyl alcohol. The pseudo-ternary diagrams were constructed in order to define Winsor s equilibrium regions. The influence of parameters such as pH, C/S (cosurfactant/surfactant) ratio, distribution coefficient, initial dye concentration, salinity, temperature, phases relative amounts, loading capacity of the microemulsion phase and dye reextraction rate has also been investigated. An experimental planning (Scheffé Net) was used to optimize the extraction process. The removal of color and metals reached levels as high as 99%
Resumo:
Gait speed has been described as a predictive indicator of important adverse outcomes in older populations. Among the criteria to evaluate frailty, gait speed has been identified as the most reliable predictor of fragility, practical and low cost. Objective: This study assesses the discriminating capability of gait speed in determining the presence of fragility in the elderly community in northeast of Brazil. Method: We performed an observational analytic study with a transversal character with a sample of 391 community-living elders, aged 65 years or older, of both sexes, in the city of Santa Cruz-RN. Participants were interviewed using a multidimensional questionnaire to obtain sociodemographic information, physical-related and mental health-related information. The unintentional weight loss, muscle weakness, self-reported exhaustion, slow gait and low-physical activity were considered to evaluate the frailty syndrome. Gait velocity was measured as the time taken to walk the middle 4,6 meters of 8,6 meters (excluding 2 meters to warm-up phase and 2 meters to deceleration phase).We calculate the sensitivity and specificity of gait speed test in different cutoff points for the test run time, from which ROC curve was constructed as a measure of test predictive value to identify frail elders. The prevalence of frailty in Santa Cruz-RN was 17.1%. The gait speed test accuracy was 71%when speed is below 0,91m/s. Among women, the gait speed test accuracy was 80%(gait speed below 0.77m/s) and among men, the test accuracy was 86% (gait spend below 0,82%) (p<0,0001).Conclusion: our findings have clinical relevance when we consider that the detection of frailty presence by the gait speed test can be observed in elderly men and women by a simple, cheap and efficient exam
Resumo:
Introduction: The SPPB provides information about physical function and is a predictor of adverse events in the elderly. Frailty is a multidimensional syndrome that increases susceptibility to diseases and disability. However it may be possible to prevent or postpone frailty if is identified early. Our objective is to analyze SPPB s ability in screening for frailty a community-dwelling young elderly from cities with distinct socioeconomic conditions. Methods: Data were originated from community dwelling adults (65-74 years old) in Canada (Saint Bruno; n = 60) and Brazil (Santa Cruz; n = 64). SPPB was used to assess physical performance. Frailty was defined as the presence of ≥ 3 of these criteria: weight loss, exhaustion, weakness, mobility limitation and low physical activity. One point was given for each criterion met, totalizing a frailty score ranged from 0 to 5. The Linear Regression and Receiver Operating Characteristics analyses were performed to evaluate the SPPB s screening ability. Results: Mean age was 69.48, 10.0% of the Saint Bruno s sample and 28.1% of Santa Cruz s were frail (p = 0.001), the SPPB score means were 9.6 and 8.5 respectively (p = 0.01). SPPB correlated with the frailty score (R2 = 0.33), with better results for Saint Bruno. A cutoff of 9 in SPPB had good sensitivity and specificity in discriminating frail from non frail in Saint Bruno (AUC = 0.81) but showed fair results in Santa Cruz (AUC = 0.61). Conclusion: The SPPB has moderate ability in predicting frailty among older adult s population, and is an useful test to identify people with good functionality and low frailty when SPPB scores are ≥9
Resumo:
Introduction: The frailty in the elderly is the result of a complex interplay between many social and clinical factors involved in its genesis. Although there is an understanding of its association with increased risk of adverse clinical outcomes, still it is unclear whether this syndrome can be aggravated due to lack of social support. So, the objective of this study was to analyze the association between social support and frailty syndrome in elderly community residents. Materials and methods: Observational analytical cross-sectional study, with a sample of 300 elderly living in the city of Natal-RN. Were collected informations about socialdemographic, economics and physical health data. The Social support was assessed by the status of cohabitation; marital status; contact frequency and diversity rate; received and given attendance frequency rate; and Map Minimum Relations of the Elderly. The frailty was assessed using the following criteria: unintentional weight loss, weakness, low physical activity, exhaustion and Slowness. To observe any possible associations, we performed the Pearson chi-square test, the Student t test and multivariate analysis using binary logistic regression, adopting a significance level of 5%. Results: It was observed that there were no associations of frailty with the social support variables, except for housekeeping mode (p = 0.046) of the MMRI. For the sociodemographic, economic, physical health and social support data, only age (p <0.001), sedentary lifestyle (p = 0.002) and poor perceived health (p = 0.001) were the ones that remained in the logistic regression model, with strong association for the presence of frailty. Conclusion: Among the variables related to social support, only to help with housekeeping was significantly associated with frailty. However, more studies need to be developed to characterize the social vulnerability, as well as health services need to recognize the importance of social support as an integral part of care for the elderly