Análise de desempenho de um fogão solar construído a partir de sucatas de antena de tv

Given the growing environmental crisis caused by degradation, mainly due to the use of polluting energy sources, increasing the growing use of renewable energies worldwide, with emphasis on solar energy, an abundant supply and available to everyone, which can be harnessed in several ways: electricity generation; dehydration of food; heating, disinfection and distillation and cooking. The latter has as its primary feature the viability of clean, renewable energy for society, combating ecological damage caused by large-scale use of firewood for cooking foods, use in tropical countries with high solar radiation, and has funding NGOs throughout the world with the goal of achieving low-income population. The proposed project consists of a solar cooker for concentration, working from the reflection of sunlight by a hub that they converge to a focal point at the bottom of the pot, getting lots of heat. The solar cooker under study consists of two elliptical reflecting parabolas made from the recycling of scrap TV antenna, having 0.29 m² of surface area for each antenna, which were covered by multiple mirrors of 2 mm thick and mounted on a metal structure, with correction for the mobility of the apparent movement of the sun. This structure was built with the recycling of scrap metal, possessing a relatively low cost compared with other solar cookers, around US$ 50.00. This cost becomes negligible, since that will involve a great benefit to not have fuel costs for each meal, unlike the use of gas or firewood for cooking food. The tests show that the cooker has reached the maximum temperature of 740 ° C, for boiling water in an average time of 28 minutes, cooking various types of foods such as potatoes, rice and pasta in an average time of 45 minutes and still going as a solar oven, making pizza baking and meat. These cooking times do not differ much from the cooking times on a gas stove, it becomes the solar cooker as a good consumer acceptance, and furthermore not to deliver the same gases that can poison the food as with the wood stove. Proves the viability of using the stove to cook or bake in two daily meals for a family, still presenting a position to improve his performance with the addition of new materials, equipment and techniques

Viabilidade térmica de um forno solar fabricado com sucatas de pneus

The proposed design provides a solar furnace alternative, box-like, low-cost operation to be used in cooking, comprising three scrap tires to make the recycling thereof. The tires were coupled to each other, forming an enclosure, which stood on its bottom covered by a parable multiple mirrors made from a urupema (sieve indigenous) and the inner sides of the oven aluminum sheet painted black, obtained from beer cans, thus being made to obtain the increase in the concentration of solar radiation incident on the inside of the prototype studied. Two tires were attached, leaving an air layer between them, with the function of thermal insulation. The third tire aimed to support the other two and thermally insulate the bottom of the oven. Externally was placed a metal frame with flat mirrors to reflect the incident rays into the oven, having a mobility to correct the apparent motion of the sun. Its primary feature is the viability of clean, renewable energy to society by tackling the ecological damage caused by the large-scale use of wood for cooking food. The tests show that the furnace reached the maximum temperature of 123.8 °C and baking various foods such as pizza, bun, and other lasagne in an average time 50 minutes. Proves the feasibility of using the oven. Presenting still able to improve their performance with the addition of new materials, equipment and techniques

Estudo da circulação hidrodinâmica e da dispersão de óleo na zona costeira entre Macau e Galinhos RN

This paper presents a study on coastal hydrodynamics and the spread of an oil spill in waters off Macau and Galinhos, on the east coast of the state of Rio Grande do Norte in Northeast Brazil. This area has a very marked coastal dynamic owing to the complexity of its geomorphological features, developed in a regime of semidiurnal mesotides involving reefs, spits, estuaries, mangroves, lakes and dunes. The region also plays an important role in the socioeconomic development of the state, given that the production of oil, natural gas, salt and shrimp is concentrated there. The series of oil platforms is interconnected by a pipeline system that carries oil to the local terminal. This pipeline could leak at any moment, causing immense ecological damage. To gauge the risks of an oil leak and resulting contamination of the coastal region, two hydrodynamic scenarios were simulated. The results obtained were used to implement a contaminant transport model with the creation of various oil leak scenarios modeled at different volumes (from small to large) and intensities (sporadic and continuous), at points considered critical for the model (on two platforms and at two pipeline intersections), under different wind (summer and winter) and tidal (high and low at new, full and quarter moon phases) conditions. The use of hydrodynamic circulation computer models as a tool for representing a real project design has been increasingly frequent in recent years, given that they enable the realistic simulation of the hydrodynamic circulation pattern in bodies of water and an analysis of the impacts caused by contaminants released into the water. This study used the computer models contained in SisBAHIA®, in continuous development in the area of Coastal Engineering and Oceanography at COPPE/UFRJ