Bolton freeware: aplicativo de avaliação de discrepância de massa dentária desenvolvido pelo programa de pós-graduação em odontologia/UFRN

The calculation of tooth mass discrepancy, essential for good planning and a proper orthodontic finishing, when performed manually, besides being laborious, requires considerable time consumption. The aim of this study was to develop and test Bolton Freeware, a software for analysis of the tooth mass discrepancy of Bolton, aiming to minimize the consumption of time in a less onerous way. The digital analysis of the software was done by means of two-dimensional scanning of plaster study models and compared to manual evaluation (gold standard), using 75 pairs of stone plaster study models divided into two groups according to the magnitude of the Curve of Spee (group I from 0 to 2 mm, group II greater than 2 to 3mm). All the models had permanent dentition and were in perfect condition. The manual evaluation was performed with a digital caliper and a calculator, and the time required to perform the analysis for both methods was recorded and compared. In addition, the software was evaluated by orthodontists regarding its use, by means of questionnaires developed specifically for this purpose. Calibration was performed prior to manual analysis, and excellent levels of inter-rater agreement were achieved, with ICC > 0.75 and r > 0.9 for total and anterior proportion. It was observed in the evaluation of error of the digital method that some teeth showed a significant systematic error, being the highest measured at 0.08 mm. The analysis of total tooth mass discrepancy performed by Bolton Freeware, for those cases in which the curve of Spee is mild and moderate, differ from manual analysis, on average, 0.09 mm and 0.07 mm respectively, for each tooth evaluated, with r> 0, 8 for total and anterior proportion. According to the specificity and sensitivity test, Bolton Freeware has an improved ability to detect true negatives, i.e. the presence of discrepancy. The Bolton analysis digitally performed was faster, with an average difference of time consumed to perform the analysis of Bolton between the two methods of approximately 6 minutes. Most experts interviewed (93%) approved the usability of the software

Incidência de cárie dentária em adolescentes em município do Nordeste brasileiro, 2006

NORO, Luiz Roberto Augusto et al. Incidência de cárie dentária em adolescentes em município do Nordeste brasileiro, 2006, Cadernos de Saúde Pública, Rio de Janeiro, v. 25, n. 4, p. 783-790, abr. 2009.

Avaliação da eficácia de selante ionomérico modificado por resina e escovação dentária na preservação de cárie oclusal

The purpose of this study was to evaluate the effectiveness during a twelve-month period, of resin-modified glass ionomer (Vitremer@) used as fissure sealants compared to supervised teeth brushing in the prevention of oclusal caries in permarient molars of pubIlc school children from 5 to 7 years of age. A total of 91 children participated in the study, being randomly divided up into three groups of investigation: group with sealant (n=31), group of supervised brushing (m=30), and control gorup (n=30). After 12 months, a total of 28.5% of tosses in the sample of 26 children was registered, and although there wasn t a significant diference between these losses and the groups studles (p = 0.6355), there was a considerable reduction in the sample. The results showed that none of the independentIy studied variables (present caries experience, biofilm, bleeding, sealant retention, position of the tooth in the arch, and sex) interfered in the final results, and that there was no significant difference between applying the sealant in question, perfornling supervised dental brushing, or not intervening at alI (p=0.542). These results could have been a consequence of the limitations found alI through the study, especially relating to the losses occurred because of school evasion, transfer, or because of the accident in the Marise Paiva Municipal School, Keeping students away for approximately one semester, so tht a new reseach had to be developed sos as to better clarify the effects among the treatments done there

Prevalência e determinantes de oclusopatias nas dentições decídua, mista e permanente na cidade do Natal/RN

This work is intended to bring a contribuition to the verification of the prevalance of malocclusion in the deciduous, permanent and mixed dentition in the student population in the city of Natal, Brazil. In this purpose, a sectional study of infantiles aging 5, 8 and 12 years old was carried out. The average prevalance of malocclusions in the group as a whole was 76,5%. Considering the different dentitions separately, the study showed malocclusion prevalence as follows: Deciduous Dentition 75,5%; Mixed Dentition 84% and Permanent Dentition 70,5%. The most common malocclusion cases found in the deciduous dentition were openbite (20.6%); overbite (16.6%) and maxillary overjet (14,7). Mixed Dentition: the most commonly found occlusional malfunctions in this dentitional phase were maxillary overjet (33,8%); crowding (28,3%), and mandillary discrepancy (19,9%). In the univaried analysis, he application of the Chi square test of independence, (significance 5%), has indicated a meaningful association of the variables social class (p=0,019), primata space (p = 0,036), habits (p= 0,002) and time-and-habit (P=0,03). The same test on the permanent dentition group revealed a significant association for the independent variables, as follows: Social class (p=O,OOO), School (p=O,OOI), Income (p=O,OOO), housing standard (p=0,001), facial pattem (p=0,004), caries record (p=0,031). No significant association was found in the mixed dentition. The Logistic Regression analysis on the deciduous dentition has shown that income, ethnicity, habit and canine relationship constitute factors of risk regardless of the other variables. As for the permanent dentition, only Facial Pattem was pointed as a factor of risk for the formation of malocclusion

Avaliação microscópica dos fragmentos ósseos obtidos por diferentes métodos de osteotomia e de irrigação em aloenxertos irradiados e congelados de coelho

Oral and facial bone defects can undertake appearance, psychosocial well-being and stomathognatic function of its patients. Over the yerars several strategies for bone defect regeneration have arised to treat these pathologies, among them the use of frozen and irradiated bone allograft. Manipulation of bone grafts it s not determined yet, and several osteotomy alternatives can be observed. The present work evaluated with a microscope the bone fragments obtained from different osteotomy methods and irrigation on rings and blocks allografts irradiated and frozen at 80° negative in a rabbit model. The study is experimental in vitro and it sample was an adult male New Zealand rabbit. The animal was sacrificed to obtain long bones, that were submitted to freezing at 80º negative and irradiated with Cobalt- 60. Then the long bones were sectioned into 24 bone pieces, divided into 4 groups: G1 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thickness with high-speed handpiece with manual irrigation; G2 (n=06) osteotomy was performed with bur No. 6 forming rings with 5 mm thick with surgical motor with a manual irrigation rotation 1500 rpm; GA (n=06), osteotomy with trephine using manual irrigation with saline; and GB (n=06), osteotomy with trephine using saline from peristaltic pumps of surgical motor. Five bone pieces of each group were prepared for analysis on light microscopy (LM) and one on electronic scan electronic microscopy (SEM). On the SEM analysis edges surface, presence of microcracks and Smear Layer were evaluated. Analyzing osteotomy technics on SEM was observed: increased presence of microcracks cutting with high speed; increased presence of areas covered by Smear Layer when cutting with motor implant. The irrigation analysis with SEM was observed: that the presence of microcracks does not depend on the type of irrigation; on manual irrigation, there was greater discrepancy between the cutting lines. The descriptive analysis of the osteotomy and irrigation process on LM showed: histological analysis showing the bony margins with clear tissue changed layer, composed of blackened tissue of charred appearance near to the cortical bone; on the edges of the bony part, bone fragments that were displaced during the bone cut and bone irregularities were observed. After analysis of results we can conclude: that there was greater regularity of the bone cut using high-speed handpiece than using motor implant; the cut with trephine using saline irrigated from peristaltic pumps of surgical motor showed greater homogeneity when compared with manual irrigation; charred tissue was found in all obtained bone samples, whit no significant statistically difference on the proportion of carbonization of the two analysed technics

Reflexões metodológicas sobre prevalência da fluorose dentária nos inquéritos de saúde bucal

OBJETIVO: Analizar limitaciones del estudio de fluorosis dentaria en pesquisas transversales. MÉTODOS: Se utilizaron datos de estudios de de Condiciones de Salud Bucal de la Población Brasileña (SBBrasil 2003) y de la Investigación Nacional de la Salud Bucal (SBBrasil 2010). La estimativa de tendencia epidemiológica de la fluorosis en la población de 12 años, aspectos de la confiabilidad de los datos, así como la precisión de las estimativas, fueron evaluadas en estas dos investigaciones. La distribución de la prevalencia de la fluorosis fue hecha de acuerdo con los dominios de estudio (capitales y regiones) y el año estudiado. Se expresaron también los intervalos de confianza (IC95%) para la prevalencia simple (sin considerar las fases de la gravedad). RESULTADOS: La prevalencia de la fluorosis dentaria presentó una variación considerable, de 0 a 61% en 2003 y de 0 a 59% en 2010. Se observaron inconsistencias en los datos en términos individuales (por año y por dominio) y en el comportamiento de la tendencia. Considerando la expectativa de prevalencia y los datos disponibles en las dos investigaciones, el tamaño mínimo de la muestra debería ser de 1.500 individuos para obtener intervalos de 3,4% y 6,6% de confianza, considerando un coeficiente de variación mínimo de 15%. Dada la subjetividad en la naturaleza de su clasificación, exámenes de fluorosis dentaria pueden presentar más variación de los realizados para otras condiciones de salud bucal. El poder para establecer diferencias entre los dominios del estudio con la muestra de SBBrasil 2010 es bastante limitado. CONCLUSIONES: No fue posible analizar la tendencia de la fluorosis dentaria en Brasil con base en los estudios de 2003 y 2010; esos datos son sólo indicadores exploratorios de la prevalencia de la fluorosis. La comparación se hace imposible por el hecho de haber sido utilizado modelos de análisis diferentes en las dos pesquisas. La investigación de la fluorosis dentaria en pesquisas de base poblacional no es viable técnica y económicamente, la realización de estudios epidemiológicos localizados con plan de muestreo es más adecuada.

Projeto SB Brasil 2010 - pesquisa nacional de saúde bucal revela importante redução da cárie dentária no país

O Projeto SB Brasil 2010, planejado e executado por órgãos do SUS, nos âmbitos federal, estadual e municipal, e de universidades brasileiras, por meio de Centros Colaboradores do Ministério da Saúde se constitui em recurso de valor estratégico para aprofundar os conhecimentos sobre os agravos bucais no país, e dá contribuição inestimável para orientar os rumos da PNSB e avançar na construção de um modelo de atenção pautado na Vigilância à Saúde

Projeto SB Brasil 2010 - pesquisa nacional de saúde bucal revela importante redução da cárie dentária no país

O Projeto SB Brasil 2010, planejado e executado por órgãos do SUS, nos âmbitos federal, estadual e municipal, e de universidades brasileiras, por meio de Centros Colaboradores do Ministério da Saúde se constitui em recurso de valor estratégico para aprofundar os conhecimentos sobre os agravos bucais no país, e dá contribuição inestimável para orientar os rumos da PNSB e avançar na construção de um modelo de atenção pautado na Vigilância à Saúde

Incidência de cárie dentária em adolescentes em município do Nordeste brasileiro, 2006

NORO, Luiz Roberto Augusto et al. Incidência de cárie dentária em adolescentes em município do Nordeste brasileiro, 2006, Cadernos de Saúde Pública, Rio de Janeiro, v. 25, n. 4, p. 783-790, abr. 2009.

Influência do número de refundições da liga Ni-Cr-Mo-Ti sobre as propriedades de próteses metalocerâmicas

A frequently encountered difficulty in oral prosthetics is associated with the loss of metallic alloys during the melting stage of the production of metal-ceramic replacement systems. Remelting such materials could impar their use in oral rehabilitation due to loss in esthetics, as well as in the chemical, physical, electrochemical and mechanical properties. Nowadays, the Ni-Cr-Mo-Ti alloy is widely used in metal-ceramic systems. Manufacturers state that this material can be remelted without significant alterations in its behavior, however little has been established as to the changes in the performance of this alloy after successive remelting, which is common practice in oral prosthetics. Therefore, the objective of this study was to evaluate possible changes in the esthetics and associated properties of metalceramic samples consisting of Ni-Cr-Mo-Ti and dental porcelain. Three to five remelting steps were carried out. The results revealed that Ni-Cr-Mo-Ti can be safely used even after three remelting steps. Further remelting significantly affect the characteristics of the alloys and should not be recommended for the manufacture of metal-ceramic systems

Análise mecânica e microestrutural das ligas de cobalto-cromo de uso odontológico após sucessivas refundições

The cobalt-chromium alloy is extensively used in the Odontology for the confection of metallic scaffolding in partial removable denture. During the last few years, it has been reported an increasing number of premature imperfections, with a few months of prosthesis use. The manufacture of these components is made in prosthetic laboratories and normally involves recasting, using parts of casting alloy and parts of virgin alloy. Therefore, the objective of the present study was to analyze the mechanical properties of a commercial cobalt-chromium alloy of odontological use after successive recasting, searching information to guide the dental prosthesis laboratories in the correct manipulation of the cobalt-chromium alloy in the process of casting and the possible limits of recasting in the mechanical properties of this material. Seven sample groups were confectioned, each one containing five test bodies, divided in the following way: G1: casting only with virgin alloy; G2: casting with 50% of the alloy of the G1 + 50% of virgin alloy; G3: casting with 50% of the alloy of the G2 + 50% of virgin alloy; G4: casting with 50% of the alloy of the G3 + 50% of virgin alloy; G5: 50% of alloy of the G4 + 50% of virgin alloy; G6: 50% of alloy of the G5 + 50% of virgin alloy and finally the G7, only with recasting alloy. The modifications in the mechanical behavior of the alloy were evaluated. Moreover, it was carried the micro structural characterization of the material by optic and electronic scanning microscopy, and X ray diffraction.and fluorescence looking into the correlatation of the mechanical alterations with structural modifications of the material caused by successive recasting process. Generally the results showed alterations in the fracture energy of the alloy after successive recasting, resulting mainly of the increasing presence of pores and large voids, characteristic of the casting material. Thus, the interpretation of the results showed that the material did not reveal significant differences with respect to the tensile strength or elastic limit, as a function of successive recasting. The elastic modulus increased from the third recasting cycle on, indicating that the material can be recast only twice. The fracture energy of the material decreased, as the number of recasting cycles increased. With respect to the microhardness, the statistical analyses showedno significant differences. Electronic scanning microscopy revealed the presence of imperfections and defects, resulting of the recasting process. X ray diffraction and fluorescence did not show alterations in the composition of the alloy or the formation of crystalline phases between the analyzed groups. The optical micrographs showed an increasing number of voids and porosity as the material was recast. Therefore, the general conclusion of this study is that the successive recasting of of Co-Cr alloys affects the mechanical properties of the material, consequently leading to the failure of the prosthetic work. Based on the results, the best recommendadition is that the use of the material should be limited to two recasting cycles

Estudo da viabilidade do processo de reciclagem do material descartado do sistema Zirkonzanh® de produção de próteses dentárias

At present, the material of choice for performing aesthetic dental prosthetic work is in the ceramic. Among them, the ceramic base of stabilized zirconia with 3% yttria (3Y - TZP) stand out for having excellent physical and mechanical properties. During the machining of blocks of zirconia in the laboratory to prepare the various types of prostheses, much of the material is given off in the form of powder, which is subsequently discarded. The waste of this material results in financial loss, reflecting higher final cost treatment for patients, as well as damage to the environment, thanks to the processes involved in the manufacture and disposal of the ceramic. This research, pioneered the recycling of zirconium oxide powder obtained during milling of dental crowns and bridges, we highlight the social and environmental aspects and aims to establish a protocol for the reuse of waste (powder of zirconia Zirkonzahn® system) discarded to obtain a new block of compacted zirconia to maintain the same mechanical and microstructural properties of commercial high-cost imported material. To compare with the commercial material, samples were uniaxially (20 MPa) and isostatically (100 MPa), and its mechanical and microstructural characterization was performed through tests of density, porosity, dilatometry, X-ray diffraction (XRD), hardness, fracture toughness, resistance to fracture electron microscopy (SEM) and analysis of grain size. The results observed in the samples were isostatically pressed similiares those obtained with samples from the commercial material demonstrating the viability of the process

Modelagem analítica e experimental da filtração em meios porosos

Deep bed filtration occurs in several industrial and environmental processes like water filtration and soil contamination. In petroleum industry, deep bed filtration occurs near to injection wells during water injection, causing injectivity reduction. It also takes place during well drilling, sand production control, produced water disposal in aquifers, etc. The particle capture in porous media can be caused by different physical mechanisms (size exclusion, electrical forces, bridging, gravity, etc). A statistical model for filtration in porous media is proposed and analytical solutions for suspended and retained particles are derived. The model, which incorporates particle retention probability, is compared with the classical deep bed filtration model allowing a physical interpretation of the filtration coefficients. Comparison of the obtained analytical solutions for the proposed model with the classical model solutions allows concluding that the larger the particle capture probability, the larger the discrepancy between the proposed and the classical models

Ecogenômica de archaea e monitoramento de comunidades de procariotos redutores de sulfato: aplicações na indústria de petróleo e gás

The human activities responsible for the ambient degradation in the modern world are diverse. The industrial activities are preponderant in the question of the impact consequences for brazilian ecosystems. Amongst the human activities, the petroliferous industry in operation in Potiguar Petroliferous Basin (PPB) displays the constant risk of ambient impacts in the integrant cities, not only for the human populations and the environment, but also it reaches the native microorganisms of Caatinga ground and in the mangrove sediment. Not hindering, the elaboration of strategies of bioremediation for impacted areas pass through the knowledge of microbiota and its relations with the environment. Moreover, in the microorganism groups associated to oil, are emphasized the sulfate-reducing prokaryotes (SRP) that, in its anaerobic metabolism, these organisms participate of the sulfate reduction, discharging H2S, causing ambient risks and causing the corrosion of surfaces, as pipelines and tanks, resulting in damages for the industry. Some ancestries of PRS integrate the Archaea domain, group of microorganisms whose sequenced genomes present predominance of extremophilic adaptations, including surrounding with oil presence. This work has two correlated objectives: i) the detection and monitoring of the gene dsrB, gift in sulfate-reducing prokaryotes, through DGGE analysis in samples of mDNA of a mangrove sediment and semiarid soil, both in the BPP; ii) to relate genomic characteristics to the ecological aspects of Archaea through in silico studies, standing out the importance to the oil and gas industry. The results of the first work suggest that the petrodegraders communities of SRP persist after the contamination with oil in mangrove sediment and in semiarid soil. Comparing the populations of both sites, it reveals that there are variations in the size and composition during one year of experiments. In the second work, functional and structural factors are the probable cause to the pressure in maintenance of the conservation of the sequences in the multiple copies of the 16S rDNA gene. Is verified also the discrepancy established between total content GC and content GC of the same gene. Such results relating ribosomal genes and the ambient factors are important for metagenomic evaluations using PCR-DGGE. The knowledge of microbiota associated to the oil can contribute for a better destination of resources by the petroliferous industry and the development of bioremediation strategies. Likewise, search to lead to the best agreement of the performance of native microbiota in biogeochemical cycles in Potiguar Petroliferous Basin ecosystem

Acesso aos serviços odontológicos e incidência de cárie em adolescentes e fatores de risco em município do Nordeste Brasileiro, 2006

The aims of this study were to analyze the access of dental services by child population, to determine the prevalence of dental caries, gingivitis and malocclusion in resident children from the municipal district of Sobral Ceará and to evaluate the incidence of the dental decay in adolescents associated with the factors related to socioeconomic condition, access to health services and self-perception. This study had as main factor the multidisciplinary represented by the participation of health professional (doctors, dentists, nurses) in the development of the survey's initial reference; student from Human Sciences area to apply the structured questionnaire in domiciliary visits; statistics professionals in the orientation of the analysis to be held and family health team (community health agents, dentists and dental clinic assistants) in the scheduling of domiciliary visits and the accomplishment of oral exam. The sample was determined from the domicile record that included children born between 1990 and 1994 to develop the research Children health conditions in the municipal district of Sobral Ceará . The first sample comprised 3425 parents of children from 5 to 9 years old, living in the urban area at the municipal district of Sobral Ceará, aiming at identifying the most important factors associated to the access to dental service. From this sample, 1021 children were selected in a systematic way, for the accomplishment to the epidemiological study of decay, gingivitis and malocclusion. In the study's third phase, in order to arrange the group to be followed, 688 adolescents were examined and interviewed, by means of the active search from the 1021 individuals that had been previously examined. It was observed that 50.9% of the children had access to dental service at least once in a lifetime. Of this total, 65.3% accomplished it during the last year, and 85.4% of these did in public services, what allows to identify the importance of this sector in the access to dental services. It was observed that the factors that most affected the access to dental 129 services were related to socioeconomic condition, such as the access to health plan, the possession of toothbrush, garbage collecting, mother s schooling, sewerage treatment and malnutrition. In relation to oral diseases, an increase in the DMF-T index according the age was observed, from 0.10 in five years old to 1.66 in the nine years old, while with the dmf-t index, the inverse happened, since the index decreased from 3.59 in five years old to 2.69 in nine years old. In relation to gingivitis, an average 32.7% of the children presented gum bleeding. In what concerns malocclusion, it was observed that 60.3% of the children didn't present any problem, 30.17% had light malocclusion and 9.5% severe malocclusion. The average incidence of dental caries was 1.86 teeth per youngster. Among the studied variables, tooth pain in the last six months, mother's income and school snack, adjusted by the perception about the need of treatment, the mother's schooling and the dentist's appointment at least once in a lifetime, were the variables that presented positive relationship with the high incidence of dental caries on this population by logistic regression. Variables of socioeconomic nature, related to the access to health services and behavior and biological variables presented a relationship with the high caries incidence. The study point out to the need of developing health actions in a humanized way, by an oral health team effectively bound to the population's interest, with the great objective to provide, with the public health services managers, adequate conditions to improve oral health